Panasonic DP-C305 Service Manual page 675
Hide thumbs
Also See for DP-C305:
- Operating instructions manual (112 pages) ,
- Scan/email manual (62 pages) ,
- Service handbook (808 pages)
Table of Contents
Advertisement
9.6.3.
Paper Size Setting (System Console)
1. Press the "Function", "Copy", and the "3" keys simultaneously on the Control Panel.
2. Input the password, and select the "OK" button to enter the Service Mode (default password is
00000000, except for DP-C322 Series which do not require a password).
3. Press the "5" key on the Control Panel, and then press the "Start" key to enter the F5 Service Mode.
4. Select "16 Paper Size Tray 3" on the Touch Panel display.
5. Select a desired Paper Size, and then select the "OK" button on the Touch Panel display.
6. Select a Media Type, and then select the "OK" button on the Touch Panel display.
Note:
For System Console 1 (DA-DS320), skip to step 10..
For System Console 2 (DA-DS321), follow the steps below.
7. Select "17 Paper Size Tray 4" on the Touch Panel display.
8. Select a desired Paper Size, and then select the "OK" button on the Touch Panel display.
9. Select a Media Type, and then select the "OK" button on the Touch Panel display.
10. Press the "Reset" key on the Control Panel to exit to the initial screen of the F5 Service Mode.
11. Press the "Function", and the "C (Clear)" keys simultaneously on the Control Panel to exit the
Service Mode.
12. Confirm that System Console (Tray 3 and/or Tray 4) is displayed on the Touch Panel Display.
9.6.4.
Adjusting the Printer Registration, LSU Image Side to Side
After installing the System Console option, the following LSU Image Side to Side adjustment must be
performed. The Printer registration is adjusted at the factory. If copy image is abnormal, adjust it by the
following procedure.
9.6.4.1.
Printer Registration
1. Insert Ledger, or A3 size paper into Tray 2, and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the Sheet Bypass tray) to disable them.
2. Press the "Function", "Copy", and the "3" keys simultaneously on the Control Panel.
3. Input the password, and select the "OK" button to enter the Service Mode (default password is
00000000, except for DP-C322 Series which do not require a password).
4. Press the "8" key on the Control Panel, and then press the "Start" key to enter the F8 Service
Mode.
5. Perform the Service Modes F8-28 (Belt Length Control).
6. Press the "Reset" key on the Control Panel to exit to the initial screen of the F8 Service Mode.
7. Press the "1" key on the Control Panel, and then press the "Start" key to enter the F1 Service
Mode.
8. Perform the Service Modes F1-03 to F1-07 (Print Test Pattern 1 to 5).
9. Check the gap of the print pattern from the paper edge, refer to the Figure below.
10. Press the "Reset" key on the Control Panel to exit to the initial screen of the F1 Service Mode.
11. Press the "6" key on the Control Panel, and then press the "Start" key to enter the F6 Service
Mode.
12. Perform the Service Mode F6-000 to F6-007 (F6-002, F6-003, and F6-004 are not used), to adjust
the gap to 5 mm.
13. If the gap is less than 5 mm, input a (-) value. If more than 5 mm, input a (+) value.
14. Press the "Reset" key first on the Control Panel, and then press the "Function", and the "C
(Clear)" keys simultaneously to exit the Service Mode.
Ver. 1.1
675
DP-C405/C305/C265
FEB 2008
- Quick Links:
- Error Codes (for Copier)
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
