Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HP 6000
Summary of Contents for HP 6000
- Page 1 Hardware Reference Guide HP Compaq 6000 Pro Microtower Business PC...
- Page 2 Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. This document contains proprietary information that is protected by copyright.
-
Page 3: About This Book
About This Book This guide provides basic information for upgrading this computer model. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. - Page 4 About This Book ENWW...
-
Page 5: Table Of Contents
Table of contents 1 Product Features Standard Configuration Features ... 1 Front Panel Components ... 2 Media Card Reader Components ... 3 Rear Panel Components ... 4 Keyboard ... 5 Using the Windows Logo Key ... 6 Serial Number Location ... 7 2 Hardware Upgrades Serviceability Features ... - Page 6 Appendix C External Security Devices Installing a Security Lock ... 46 Cable Lock ... 46 Padlock ... 47 HP Business PC Security Lock ... 47 Front Bezel Security ... 49 Appendix D Electrostatic Discharge Preventing Electrostatic Damage ... 51 Grounding Methods ... 51 Appendix E Computer Operating Guidelines, Routine Care and Shipping Preparation Computer Operating Guidelines and Routine Care ...
-
Page 7: Product Features
Product Features Standard Configuration Features The HP Compaq Microtower features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Instructions for using the utility are provided in the Troubleshooting Guide. -
Page 8: Front Panel Components
Front Panel Components Drive configuration may vary by model. Table 1-1 Front Panel Components 5.25-inch Optical Drives Optical Drive Activity Lights Hard Drive Activity Light Microphone/Headphone Connector USB (Universal Serial Bus) 2.0 Ports NOTE: When a device is plugged into the Microphone/Headphone Connector, a dialog box will pop up asking if you want to use the connector for a microphone line Line-In device or a headphone. -
Page 9: Media Card Reader Components
Media Card Reader Components The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components. Figure 1-2 Media Card Reader Components Table 1-2 Media Card Reader Components Slot MicroSD Media Card Reader... -
Page 10: Rear Panel Components
Arrangement and number of connectors may vary by model. An optional second serial port and an optional parallel port are available from HP. When a device is plugged into the blue Line-In Audio Connector, a dialog box will pop up asking if you want to use the connector for a line-in device or a microphone. -
Page 11: Keyboard
Keyboard Table 1-4 Keyboard Components Function Keys Editing Keys Status Lights Numeric Keys Arrow Keys Ctrl Keys Application Key Windows Logo Keys Alt Keys Keys available in select geographic regions. ENWW Perform special functions depending on the software application being used. Includes the following: Insert, Home, Page Up, Delete, End, and Page Down. -
Page 12: Using The Windows Logo Key
Using the Windows Logo Key Use the Windows Logo key in combination with other keys to perform certain functions available in the Windows operating system. Refer to the Table 1-5 Windows Logo Key Functions The following Windows Logo Key functions are available in Microsoft Windows XP and Microsoft Windows Vista. Windows Logo Key Windows Logo Key + Windows Logo Key +... -
Page 13: Serial Number Location
Serial Number Location Each computer has a unique serial number and product ID number that are located on the top cover of the computer. Keep these numbers available for use when contacting customer service for assistance. Figure 1-3 Serial Number and Product ID Location ENWW Serial Number Location... -
Page 14: Hardware Upgrades
To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation, setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo. WARNING! Energized and moving parts inside. -
Page 15: Removing The Computer Access Panel
Removing the Computer Access Panel Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices. -
Page 16: Replacing The Computer Access Panel
Replacing the Computer Access Panel Slide the lip on the front end of the access panel under the lip on the front of the chassis (1) then press the back end of the access panel onto the unit (2). Figure 2-2 Replacing the Computer Access Panel Ensure that the panel is completely closed (1) and tighten the two thumbscrews that secure the access panel to the chassis (2). -
Page 17: Removing The Front Bezel
Removing the Front Bezel Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices. -
Page 18: Removing Bezel Blanks
Removing Bezel Blanks On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that need to be removed before installing a drive. To remove a bezel blank: Remove the access panel and front bezel. To remove a bezel blank, push the two retaining tabs that hold the bezel blank in place towards the outer right edge of the bezel (1) and slide the bezel blank back and to the right to remove it (2). -
Page 19: Installing Additional Memory
Installing Additional Memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3- SDRAM) dual inline memory modules (DIMMs). DIMMs The memory sockets on the system board can be populated with up to four industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM. -
Page 20: Populating Dimm Sockets
Populating DIMM Sockets There are four DIMM sockets on the system board, with two sockets per channel. The sockets are labeled DIMM1, DIMM2, DIMM3, and DIMM4. Sockets DIMM1 and DIMM2 operate in memory channel A. Sockets DIMM3 and DIMM4 operate in memory channel B. Figure 2-7 DIMM Socket Locations Table 2-1... -
Page 21: Installing Dimms
will have more memory than the other, the larger amount should be assigned to Channel A. For example, if you are populating the sockets with one 1-GB DIMM, and three 512-MB DIMMs, Channel A should be populated with the 1-GB DIMM and one 512-MB DIMM, and Channel B should be populated with the two 512-MB DIMMs. - Page 22 Open both latches of the memory module socket (1), and insert the memory module into the socket (2). Figure 2-8 Installing a DIMM NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket.
-
Page 23: Removing Or Installing An Expansion Card
Removing or Installing an Expansion Card The computer has one PCI expansion slot, two PCI Express x1 expansion slots, and one PCI Express x16 expansion slot. Figure 2-9 Expansion Slot Locations Table 2-2 Expansion Slot Locations Item Description PCI expansion slot PCI Express x16 expansion slot PCI Express x1 expansion slot PCI Express x1 expansion slot... - Page 24 Release the slot cover retention latch that secures the PCI slot covers by lifting the green tab on the latch and rotating the latch to the open position. Figure 2-10 Opening the Expansion Slot Retainer Before installing an expansion card, remove the expansion slot cover or the existing expansion card.
- Page 25 If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end, and carefully rock it back and forth until the connectors pull free from the socket. Pull the expansion card straight up from the socket then away from the inside of the chassis to release it from the chassis frame.
- Page 26 Store the removed card in anti-static packaging. If you are not installing a new expansion card, install an expansion slot cover to close the open slot. CAUTION: After removing an expansion card, you must replace it with a new card or expansion slot cover for proper cooling of internal components during operation.
-
Page 27: Drive Positions
Connect external cables to the installed card, if needed. Connect internal cables to the system board, if needed. Replace the access panel. Reconnect the power cord and turn on the computer. Lock any security devices that were disengaged when the access panel was removed. Reconfigure the computer, if necessary. -
Page 28: Installing And Removing Drives
You must install guide screws to ensure the drive will line up correctly in the drive cage and lock in place. HP has provided extra guide screws for the external drive bays (four 6-32 isolation mounting guide screws and eight M3 metric guide screws), installed on the side of the drive bays. - Page 29 CAUTION: To prevent loss of work and damage to the computer or drive: If you are inserting or removing a drive, shut down the operating system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby mode. Before handling a drive, ensure that you are discharged of static electricity.
-
Page 30: System Board Drive Connections
System Board Drive Connections Refer to the following illustration and table to identify the system board drive connectors. Figure 2-18 System Board Drive Connections Table 2-4 System Board Drive Connections System Board Connector SATA0 SATA1 SATA2 SATA3 Media Card Reader NOTE: The orange SATA3 connector can be reconfigured as eSATA in the Computer Setup utility if you are installing an eSATA adapter. -
Page 31: Removing An External 5.25-Inch Or 3.5-Inch Drive
Removing an External 5.25-inch or 3.5-inch Drive CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. - Page 32 If you are removing a media card reader, disconnect the USB cable from the system board. If the media card reader has a 1394 port, disconnect the 1394 cable from the PCI card. Figure 2-20 Figure 2-21 Chapter 2 Hardware Upgrades Disconnecting the Media Card Reader USB Cable Disconnecting the Media Card Reader 1394 Cable ENWW...
- Page 33 A latch drive bracket with release tabs secures the drives in the drive bay. Lift the release tab on the latch drive bracket (1) for the drive you want to remove, then slide the drive from its drive bay (2). Figure 2-22 Removing the External Drives Remove the four guide screws (two on each side) from the old drive.
-
Page 34: Installing An External 5.25-Inch Or 3.5-Inch Drive
Remove the access panel and front bezel. Install four M3 metric guide screws in the lower holes on each side of the drive. HP has provided eight extra M3 metric guide screws on the front of the chassis, under the front bezel. The M3 metric guide screws are black. - Page 35 Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until the drive snaps into place. Figure 2-24 Sliding the External Drives into the Drive Cage Connect the power and data cables to the drive as indicated in the following illustrations. If you are installing an optical drive, connect the power cable (1) and data cable (2) to the back of the drive.
- Page 36 If you are installing a media card reader, connect the USB cable to the system board. If the media card reader has a 1394 port, connect the 1394 cable to the PCI card. Figure 2-26 Figure 2-27 If installing a new drive, connect the opposite end of the data cable to the appropriate system board connector.
- Page 37 Reconnect the power cord and any external devices, then turn on the computer. Lock any security devices that were disengaged when the access panel was removed. ENWW Installing and Removing Drives...
-
Page 38: Removing An Internal 3.5-Inch Hard Drive
Removing an Internal 3.5-inch Hard Drive NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. - Page 39 Release the drive by pulling the release tab away from the drive (1) and sliding the drive out of the bay (2). Figure 2-29 Removing a Hard Drive Remove the four guide screws (two on each side) from the old drive. You will need these screws to install a new drive.
-
Page 40: Installing An Internal 3.5-Inch Hard Drive
NOTE: The hard drive uses 6-32 isolation mounting guide screws. Four extra guide screws are installed on the exterior of the hard drive bays. The HP-supplied isolation mounting guide screws are silver and blue. Refer to extra 6-32 isolation mounting guide screws location. - Page 41 Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until the drive snaps into place. The bottom bay is for the primary hard drive. The upper bay is for an optional secondary hard drive. Figure 2-31 Sliding a Hard Drive into the Drive Bay Connect the power cable (1) and data cable (2) to the back of the hard drive.
-
Page 42: Removing And Replacing A Removable 3.5-Inch Sata Hard Drive
Reconnect the power cord and any external devices, then turn on the computer. Lock any security devices that were disengaged when the access panel was removed. Removing and Replacing a Removable 3.5-inch SATA Hard Drive Some models are equipped with a Removable SATA Hard Drive Enclosure in the 5.25-inch external drive bay. - Page 43 Remove the adhesive strip that secures the thermal sensor to the top of the hard drive (1) and move the thermal sensor away from the carrier (2). Figure 2-34 Removing the Thermal Sensor Remove the four screws from the bottom of the hard drive carrier. Figure 2-35 Removing the Security Screws ENWW...
- Page 44 Slide the hard drive back to disconnect it from the carrier then lift it up and out of the carrier. Figure 2-36 Removing the Hard Drive Place the new hard drive in the carrier then slide the hard drive back so that it seats in the SATA connector on the carrier's circuit board.
- Page 45 Replace the four screws in the bottom of the carrier to hold the drive securely in place. Figure 2-38 Replacing the Security Screws Place the thermal sensor on top of the hard drive in a position that does not cover the label (1) and attach the thermal sensor to the top of the hard drive with the adhesive strip (2).
- Page 46 Slide the cover on the carrier (1) and replace the screw on the rear of the carrier to secure the cover in place (2). Figure 2-40 Replacing the Carrier Cover Slide the hard drive carrier into the enclosure on the computer and lock it with the key provided. NOTE: The carrier must be locked for power to be supplied to the hard drive.
-
Page 47: Appendix A Specifications
Specifications Table A-1 Specifications Desktop Dimensions Height Width Depth Approximate Weight Temperature Range Operating Nonoperating Relative Humidity (noncondensing) Operating Nonoperating (38.7°C max wet bulb) Maximum Altitude (unpressurized) Operating Nonoperating NOTE: Operating temperature is derated 1.0° C per 300 m (1000 ft) to 3000 m (10,000 ft) above sea level; no direct sustained sunlight. - Page 48 Table A-1 Specifications (continued) Power Output Rated Input Current (maximum) STD PS EPA 87/89/85% @ 20/50/100% load PS This system utilizes an active power factor corrected power supply. This allows the system to pass the CE mark requirements for use in the countries of the European Union. The active power factor corrected power supply also has the added benefit of not requiring an input voltage range select switch.
-
Page 49: Battery Replacement
The lifetime of the lithium battery can be extended by plugging the computer into a live AC wall socket. The lithium battery is only used when the computer is NOT connected to AC power. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to recycle. - Page 50 NOTE: On some computer models, it may be necessary to remove an internal component to gain access to the battery. Depending on the type of battery holder on the system board, complete the following instructions to replace the battery. Type 1 Lift the battery out of its holder.
- Page 51 Insert the new battery and position the clip back into place. Figure B-3 NOTE: After the battery has been replaced, use the following steps to complete this procedure. Replace the computer access panel. Plug in the computer and turn on power to the computer. Reset the date and time, your passwords, and any special system setups using Computer Setup.
-
Page 52: Appendix C External Security Devices
External Security Devices NOTE: For information on data security features, refer to the Computer Setup (F10) Utility Guide, the Desktop Management Guide, and the HP ProtectTools Security Manager Guide (some models) at http://www.hp.com. Installing a Security Lock The security locks displayed below and on the following pages can be used to secure the computer. -
Page 53: Padlock
Padlock Figure C-2 Installing a Padlock HP Business PC Security Lock Fasten the security cable by looping it around a stationary object. Figure C-3 Securing the Cable to a Fixed Object ENWW Installing a Security Lock... - Page 54 Thread the keyboard and mouse cables through the lock. Figure C-4 Threading the Keyboard and Mouse Cables Screw the lock to the chassis using the screw provided. Figure C-5 Attaching the Lock to the Chassis Appendix C External Security Devices ENWW...
-
Page 55: Front Bezel Security
Figure C-6 Engaging the Lock Front Bezel Security The front bezel can be locked in place by installing a security screw provided by HP. To install the security screw: Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. - Page 56 Remove the security screw from the inside of the front bezel. Figure C-7 Retrieving the Front Bezel Security Screw Replace the front bezel. Install the screw through the interior of the front of the chassis into the front bezel. The screw hole is located toward the middle of the right edge of the chassis between the hard drive bay and speaker.
-
Page 57: Appendix D Electrostatic Discharge
Use conductive field service tools. ● Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of the suggested equipment for proper grounding, contact an HP authorized dealer, reseller, or service provider. NOTE: For more information on static electricity, contact an HP authorized dealer, reseller, or service provider. -
Page 58: Appendix E Computer Operating Guidelines, Routine Care And Shipping Preparation
Computer Operating Guidelines, Routine Care and Shipping Preparation Computer Operating Guidelines and Routine Care Follow these guidelines to properly set up and care for the computer and monitor: ● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ●... -
Page 59: Optical Drive Precautions
Avoid using any type of solvent, such as alcohol or benzene, which may damage the finish. Safety If any object or liquid falls into the drive, immediately unplug the computer and have it checked by an authorized HP service provider. Shipping Preparation Follow these suggestions when preparing to ship the computer: Back up the hard drive files on PD discs, tape cartridges, CDs, or USB flash drives. -
Page 60: Index
46 keyboard components 5 connector 4 line-in connector 4 line-out connector 4 locks cable lock 46 front bezel 49 HP Business PC Security Lock 47 padlock 47 media card reader features 3 installing 28 removing 25 memory installing 13... - Page 61 25 optical drive 25 PCI card 19 PCI Express card 19 security cable lock 46 front bezel 49 HP Business PC Security Lock 47 padlock 47 serial connector 4 serial number location 7 shipping preparation 53 specifications...