hit counter script
HP Compaq 6000 Pro SFF Hardware Reference Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Desktop
  5. Compaq 6000 Pro SFF
  6. Hardware reference manual

HP Compaq 6000 Pro SFF Hardware Reference Manual

Small form factor business pc
Hide thumbs Also See for Compaq 6000 Pro SFF:
Table of Contents

Advertisement

Quick Links

See also: Troubleshooting Manual , Maintenance and Service Manual
Hardware Reference Guide
HP Compaq 6000 Pro Small Form Factor Business PC

Advertisement

Table of Contents
loading

Related Manuals for HP Compaq 6000 Pro SFF

Summary of Contents for HP Compaq 6000 Pro SFF

  • Page 1 Hardware Reference Guide HP Compaq 6000 Pro Small Form Factor Business PC...
  • Page 2 Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. This document contains proprietary information that is protected by copyright.

  • Page 3: About This Book

    About This Book This guide provides basic information for upgrading this computer model. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
  • Page 4 About This Book ENWW...

  • Page 5: Table Of Contents

    Table of contents 1 Product Features Standard Configuration Features ... 1 Front Panel Components ... 2 Media Card Reader Components ... 3 Rear Panel Components ... 4 Keyboard ... 5 Using the Windows Logo Key ... 6 Serial Number Location ... 7 2 Hardware Upgrades Serviceability Features ...
  • Page 6 Appendix C External Security Devices Installing a Security Lock ... 52 Cable Lock ... 52 Padlock ... 53 HP Business PC Security Lock ... 53 Front Bezel Security ... 55 Appendix D Electrostatic Discharge Preventing Electrostatic Damage ... 57 Grounding Methods ... 57 Appendix E Computer Operating Guidelines, Routine Care and Shipping Preparation Computer Operating Guidelines and Routine Care ...

  • Page 7: Product Features

    Product Features Standard Configuration Features The HP Compaq Small Form Factor features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Instructions for using the utility are provided in the Troubleshooting Guide.

  • Page 8: Front Panel Components

    Front Panel Components Drive configuration may vary by model. Figure 1-2 Front Panel Components Table 1-1 Front Panel Components 5.25-inch Optical Drive Optical Drive Activity Light Optical Drive Eject Button Dual-State Power Button Power On Light NOTE: When a device is plugged into the Microphone/Headphone Connector, a dialog box will pop up asking if you want to use the connector for a microphone line Line-In device or a headphone.

  • Page 9: Media Card Reader Components

    Media Card Reader Components The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components. Figure 1-3 Media Card Reader Components Table 1-2 Media Card Reader Components Slot MicroSD Media Card Reader...

  • Page 10: Rear Panel Components

    Arrangement and number of connectors may vary by model. An optional second serial port and an optional parallel port are available from HP. When a device is plugged into the blue Line-In Audio Connector, a dialog box will pop up asking if you want to use the connector for a line-in device or a microphone.

  • Page 11: Keyboard

    Keyboard Figure 1-5 Keyboard Components Table 1-4 Keyboard Components Function Keys Editing Keys Status Lights Numeric Keys Arrow Keys Ctrl Keys Application Key Windows Logo Keys Alt Keys Keys available in select geographic regions. ENWW Perform special functions depending on the software application being used. Includes the following: Insert, Home, Page Up, Delete, End, and Page Down.

  • Page 12: Using The Windows Logo Key

    Windows Logo Key + any number key Chapter 1 Product Features Keyboard on page 5 Displays or hides the Start menu Displays the Desktop Minimizes all open applications Undoes Minimize All Launches My Computer Launches Find Document Launches Find Computer...

  • Page 13: Serial Number Location

    Serial Number Location Each computer has a unique serial number and product ID number in the location shown below. Keep these numbers available for use when contacting customer service for assistance. Figure 1-6 Serial Number and Product ID Location ENWW Serial Number Location...

  • Page 14: Hardware Upgrades

    To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation, setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo. WARNING! Energized and moving parts inside.

  • Page 15: Removing The Computer Access Panel

    Removing the Computer Access Panel Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.

  • Page 16: Replacing The Computer Access Panel

    Replacing the Computer Access Panel Slide the lip on the front end of the access panel under the lip on the front of the chassis (1) then press the back end of the access panel onto the unit so that it locks into place (2). Figure 2-2 Replacing the Access Panel Chapter 2 Hardware Upgrades...

  • Page 17: Removing The Front Bezel

    Removing the Front Bezel Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.

  • Page 18: Removing Bezel Blanks

    Removing Bezel Blanks On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that need to be removed before installing a drive. To remove a bezel blank: Remove the access panel and front bezel. To remove a bezel blank, push the two retaining tabs that hold the bezel blank in place towards the outer right edge of the bezel (1) and slide the bezel blank back and to the right to remove it (2).

  • Page 19: Replacing The Front Bezel

    Replacing the Front Bezel Insert the three hooks on the bottom side of the bezel into the rectangular holes on the chassis (1) then rotate the top side of the bezel onto the chassis (2) and snap it into place. Figure 2-5 Replacing the Front Bezel ENWW...

  • Page 20: Using The Small Form Factor Computer In A Tower Orientation

    Figure 2-6 Changing from Desktop to Tower Orientation NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the optional tower stand. Reconnect the power cord and any external devices, then turn on the computer. NOTE: Ensure at least 10.2 centimeters (4 inches) of space on all sides of the computer remains clear...

  • Page 21: Installing Additional Memory

    Installing Additional Memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3- SDRAM) dual inline memory modules (DIMMs). DIMMs The memory sockets on the system board can be populated with up to four industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM.

  • Page 22: Populating Dimm Sockets

    Populating DIMM Sockets There are four DIMM sockets on the system board, with two sockets per channel. The sockets are labeled DIMM1, DIMM2, DIMM3, and DIMM4. Sockets DIMM1 and DIMM2 operate in memory channel A. Sockets DIMM3 and DIMM4 operate in memory channel B. Figure 2-7 DIMM Socket Locations Table 2-1...

  • Page 23: Installing Dimms

    will have more memory than the other, the larger amount should be assigned to Channel A. For example, if you are populating the sockets with one 1-GB DIMM, and three 512-MB DIMMs, Channel A should be populated with the 1-GB DIMM and one 512-MB DIMM, and Channel B should be populated with the two 512-MB DIMMs.
  • Page 24 Rotate up the external drive bay housing to access the memory module sockets on the system board. Figure 2-8 Rotating the Drive Cage Up Chapter 2 Hardware Upgrades ENWW...
  • Page 25 Open both latches of the memory module socket (1), and insert the memory module into the socket (2). Figure 2-9 Installing a DIMM NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket.

  • Page 26: Removing Or Installing An Expansion Card

    Removing or Installing an Expansion Card The computer has one PCI expansion slot, two PCI Express x1 expansion slots, and one PCI Express x16 expansion slot. NOTE: The PCI and PCI Express slots support only low profile cards. Figure 2-10 Expansion Slot Locations Table 2-2 Expansion Slot Locations...
  • Page 27 Locate the correct vacant expansion socket on the system board and the corresponding expansion slot on the back of the computer chassis. Release the slot cover retention latch that secures the PCI slot covers by lifting the green tab on the latch and rotating the latch to the open position.
  • Page 28 If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end, and carefully rock it back and forth until the connectors pull free from the socket. Pull the expansion card straight up from the socket then away from the inside of the chassis to release it from the chassis frame.
  • Page 29 If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the card and carefully rock the card back and forth until the connectors pull free from the socket. Pull the expansion card straight up from the socket then away from the inside of the chassis to release it from the chassis frame.
  • Page 30 To install a new expansion card, hold the card just above the expansion socket on the system board then move the card toward the rear of the chassis so that the bracket on the card is aligned with the open slot on the rear of the chassis. Press the card straight down into the expansion socket on the system board.
  • Page 31 If the computer was on a stand, replace the stand. Reconnect the power cord and turn on the computer. Lock any security devices that were disengaged when the access panel was removed. Reconfigure the computer, if necessary. Refer to the Computer Setup (F10) Utility Guide for instructions on using Computer Setup.

  • Page 32: Drive Positions

    Drive Positions Figure 2-17 Drive Positions Table 2-3 Drive Positions 3.5-inch internal hard drive bay 3.5-inch external drive bay for optional drives (media card reader shown) 5.25-inch external drive bay for optional drives (optical drive shown) NOTE: The drive configuration on your computer may be different than the drive configuration shown above.

  • Page 33: Installing And Removing Drives

    You must install guide screws to ensure the drive will line up correctly in the drive cage and lock in place. HP has provided extra guide screws for the external drive bays (five 6-32 standard screws and four M3 metric screws), installed in the front of the chassis, under the front bezel. The 6-32 standard screws are required for a secondary hard drive.
  • Page 34 CAUTION: To prevent loss of work and damage to the computer or drive: If you are inserting or removing a drive, shut down the operating system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby mode. Before handling a drive, ensure that you are discharged of static electricity.

  • Page 35: System Board Drive Connections

    System Board Drive Connections Refer to the following illustration and table to identify the system board drive connectors. Figure 2-19 System Board Drive Connections Table 2-4 System Board Drive Connections System Board Connector SATA0 SATA1 SATA2 SATA3 Media Card Reader NOTE: The orange SATA3 connector can be reconfigured as eSATA in the Computer Setup utility if you are installing an eSATA adapter.

  • Page 36: Removing An External 5.25-Inch Drive

    Removing an External 5.25-inch Drive CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. To remove a 5.25-inch external drive: Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices.
  • Page 37 If removing an optical drive, disconnect the power cable (1) and data cable (2) from the rear of the optical drive. Figure 2-21 Disconnecting the Power and Data Cables Rotate the drive cage back down to its normal position. CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down.

  • Page 38: Installing An Optical Drive Into The 5.25-Inch Drive Bay

    Press down on the green drive retainer button located on the left side of the drive to disengage the drive from the drive cage (1). While pressing the drive retainer button, slide the drive back until it stops, then lift it up and out of the drive cage (2). Figure 2-23 Removing the 5.25-inch Drive NOTE:...
  • Page 39 Install four M3 metric guide screws in the lower holes on each side of the drive. HP has provided four extra M3 metric guide screws on the front of the chassis, under the front bezel. The M3 metric guide screws are black. Refer to the extra M3 metric guide screws location.
  • Page 40 Rotate the drive cage to its upright position. Figure 2-26 Rotating the Drive Cage Up Connect the SATA data cable to the white system board connector labeled SATA1. Route the data cable through the cable guides. CAUTION: There are two cable guides that keep the data cable from being pinched by the drive cage when raising or lowering it.

  • Page 41: Removing An External 3.5-Inch Drive

    Rotate the drive cage back down to its normal position. CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down. Figure 2-28 Rotating the Drive Cage Down Replace the access panel. If the computer was on a stand, replace the stand. Reconnect the power cord and turn on the computer.
  • Page 42 Disconnect the drive cables from the rear of the drive, or, if you are removing a media card reader, disconnect the USB and 1394 cables from the system board as indicated in the following illustrations. NOTE: On some models, the media card reader does not include a 1394 port or cable. Figure 2-29 Disconnecting the Media Card Reader USB Cable Figure 2-30...

  • Page 43: Installing A Drive Into The 3.5-Inch External Drive Bay

    Install guide screws to ensure the drive will line up correctly in the drive cage and lock in place. HP has provided extra guide screws for the external drive bays (four 6-32 standard screws and four M3 metric screws), installed in the front of the chassis, under the front bezel. A secondary hard drive uses 6-32 standard screws.
  • Page 44 Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive toward the front of the computer until it locks into place. Figure 2-32 Installing a Drive into the 3.5-inch Drive Bay (Media Card Reader Shown) Connect the appropriate drive cables: If installing a second hard drive, connect the power and data cables to the rear of the drive and connect the other end of the data cable to the next available (unpopulated) SATA...

  • Page 45: Removing And Replacing The Primary 3.5-Inch Internal Sata Hard Drive

    Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive NOTE: The system does not support Parallel ATA (PATA) hard drives. Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive.
  • Page 46 Rotate the power supply to its upright position. The hard drive is located beneath the power supply. Figure 2-34 Raising the Power Supply Disconnect the power cable (1) and data cable (2) from the back of the hard drive. Figure 2-35 Disconnecting the Hard Drive Power Cable and Data Cable Chapter 2 Hardware Upgrades ENWW...
  • Page 47 Press down on the green release latch next to the hard drive (1). While holding the latch down, slide the drive forward until it stops, then lift the drive up and out of the bay (2). Figure 2-36 Removing the Hard Drive To install a hard drive, you must transfer the silver and blue isolation mounting guide screws from the old hard drive to the new hard drive.
  • Page 48 Align the guide screws with the slots on the chassis drive cage, press the hard drive down into the bay, then slide it back until it stops and locks in place. Figure 2-38 Installing the Hard Drive Connect the power and data cables to the back of the hard drive. NOTE: When replacing the primary hard drive, be sure to route the SATA and power cables through the cable guide on the bottom of the chassis frame behind the hard drive.

  • Page 49: Removing And Replacing A Removable 3.5-Inch Sata Hard Drive

    Removing and Replacing a Removable 3.5-inch SATA Hard Drive Some models are equipped with a Removable SATA Hard Drive Enclosure in the 5.25-inch external drive bay. The hard drive is housed in a carrier that can be quickly and easily removed from the drive bay.
  • Page 50 Remove the four screws from the bottom of the hard drive carrier. Figure 2-41 Removing the Security Screws Slide the hard drive back to disconnect it from the carrier then lift it up and out of the carrier. Figure 2-42 Removing the Hard Drive Chapter 2 Hardware Upgrades ENWW...
  • Page 51 Place the new hard drive in the carrier then slide the hard drive back so that it seats in the SATA connector on the carrier's circuit board. Be sure the connector on the hard drive is pressed all the way into the connector on the carrier's circuit board. Figure 2-43 Replacing the Hard Drive Replace the four screws in the bottom of the carrier to hold the drive securely in place.
  • Page 52 Place the thermal sensor on top of the hard drive in a position that does not cover the label (1) and attach the thermal sensor to the top of the hard drive with the adhesive strip (2). Figure 2-45 Replacing the Thermal Sensor Slide the cover on the carrier (1) and replace the screw on the rear of the carrier to secure the cover in place (2).

  • Page 53: Specifications

    Desktop Dimensions (in the desktop position) Height Width Depth Approximate Weight Weight Supported (maximum distributed load in desktop position) Temperature Range Operating Nonoperating NOTE: Operating temperature is derated 1.0° C per 300 m (1000 ft) to 3000 m (10,000 ft) above sea level; no direct sustained sunlight.

  • Page 54: Appendix A Specifications

    Table A-1 Specifications (continued) Rated Line Frequency Power Output Rated Input Current (maximum) STD PS EPA 87/89/85% @ 20/50/100% load PS This system utilizes an active power factor corrected power supply. This allows the system to pass the CE mark requirements for use in the countries of the European Union.

  • Page 55: Battery Replacement

    The lifetime of the lithium battery can be extended by plugging the computer into a live AC wall socket. The lithium battery is only used when the computer is NOT connected to AC power. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to recycle.
  • Page 56 NOTE: On some computer models, it may be necessary to remove an internal component to gain access to the battery. Depending on the type of battery holder on the system board, complete the following instructions to replace the battery. Type 1 Lift the battery out of its holder.
  • Page 57 Insert the new battery and position the clip back into place. Figure B-3 NOTE: After the battery has been replaced, use the following steps to complete this procedure. Replace the access panel. If the computer was on a stand, replace the stand. Plug in the computer and turn on power to the computer.

  • Page 58: Appendix C External Security Devices

    External Security Devices NOTE: For information on data security features, refer to the Computer Setup (F10) Utility Guide, the Desktop Management Guide, and the HP ProtectTools Security Manager Guide (some models) at http://www.hp.com. Installing a Security Lock The security locks displayed below and on the following pages can be used to secure the computer.

  • Page 59: Padlock

    Padlock Figure C-2 Installing a Padlock HP Business PC Security Lock Fasten the security cable by looping it around a stationary object. Figure C-3 Securing the Cable to a Fixed Object ENWW Installing a Security Lock...
  • Page 60 Thread the keyboard and mouse cables through the lock. Figure C-4 Threading the Keyboard and Mouse Cables Screw the lock to the chassis using the screw provided. Figure C-5 Attaching the Lock to the Chassis Appendix C External Security Devices ENWW...

  • Page 61: Front Bezel Security

    Figure C-6 Engaging the Lock Front Bezel Security The front bezel can be locked in place by installing a security screw provided by HP. To install the security screw: Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer.
  • Page 62 Remove one of the five silver 6-32 standard screws located on the front of the chassis behind the bezel. Figure C-7 Retrieving the Front Bezel Security Screw Replace the front bezel. Install the security screw next to the middle front bezel release tab to secure the front bezel in place.

  • Page 63: Appendix D Electrostatic Discharge

    Use conductive field service tools. ● Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of the suggested equipment for proper grounding, contact an HP authorized dealer, reseller, or service provider. NOTE: For more information on static electricity, contact an HP authorized dealer, reseller, or service provider.

  • Page 64: Appendix E Computer Operating Guidelines, Routine Care And Shipping Preparation

    ● Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place the keyboard, with the keyboard feet down, directly against the front of the desktop unit as this also restricts airflow. ●...

  • Page 65: Optical Drive Precautions

    Avoid using any type of solvent, such as alcohol or benzene, which may damage the finish. Safety If any object or liquid falls into the drive, immediately unplug the computer and have it checked by an authorized HP service provider. Shipping Preparation Follow these suggestions when preparing to ship the computer: Back up the hard drive files on PD discs, tape cartridges, CDs, or USB flash drives.

  • Page 66: Index

    52 keyboard components 5 connector 4 line-in connector 4 line-out connector 4 locks cable lock 52 front bezel 55 HP Business PC Security Lock 53 padlock 53 media card reader features 3 installing 37 removing 35 memory installing 15...
  • Page 67 35 optical drive 30 PCI card 22 PCI Express card 23 security cable lock 52 front bezel 55 HP Business PC Security Lock 53 padlock 53 serial connector 4 serial number location 7 shipping preparation 59 specifications...

This manual is also suitable for:

Compaq 6000 pro small form factorXz874utVs825ut

Table of Contents