200hz lcd tv signature series in full hd, premium series in full hd, true cinematic series, modern classic series, sleek & stylish series, home theatre systems, portable dvd players (2 pages)
OPERATION. REPLACE THESE COMPONENTS WITH 6) Check the line cords for cracks and abrasion. SONY PARTS WHOSE PART NUMBERS APPEAR AS Recommend the replacement of any such line cord to the SHOWN IN THIS MANUAL OR IN SUPPLEMENTS customer.
This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com (2) Press position (NG for red marking portion) 1-6. Attachment & Detachment of MDF61 Connector...
Page 5
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 b) Detachment c) Confirmation of Lock Condition (1) Hold between the lock part and harness of socket. (1) Confirm the lock conditions. When lock is completed, Release the lock and pull out connector within 20 base and socket must be same line as shown in Figure degree.
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 1-8. REMOVAL AND INSTALLATION OF REAR COVER PROCEDURE a) REMOVAL Note: Please refer to Section 4 : Disassembly for screws informations . PULL PUSH POINT PUSH a. PHOTO SHOW THE POSITION c.
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 1-9. Removal of Switch Unit Procedure a) REMOVAL Push this position to remove Push and slant towards inner side of set. Switch Unit more easily Push and slant towards inner side of set to remove Switch Unit correctly. –...
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 SECTION 2 SELF DIAGNOSTIC FUNCTION 2-1. Overview of Control Buttons 2-4. LED Pattern When safety shutdown occurs, Standby LED display reports the cause by using the lightning patterns as indicated below. Power PROG +/-/ 2.0 sec...
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 2-5. Standby LED Error Display Perform below countermeasures according to Standby LED blinking times. Blinking times Error Countermeasure DC_DET Replace either/all z Power board - Power Unit(32" & 52") - IP1 (40") - IP2 (46") z BA Board DC_ALERT...
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 SECTION 3 TROUBLESHOOTING 3.1 Flowchart 3-1-1. Flowchart A(i) Flowchart A(ii) No Power/Shut down/No Picture Try On/Off at Main SW and with Remote Commander Check Harness holder, Header pin Is it LED(STBY) Is it correct and Wire harness.
Page 12
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 3-1-2. Flowchart B 3-1-3. Flowchart C – 12 –...
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 3-1-4. Flowchart D Panel Problem Is it LED(STBY) Backlight indicator turn on turn on? or blinked? Count blink and replace board to Re-connect LVDS wire at T-Con Is it correct obey with 2-6 triage chart. and at BA board.
Page 14
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 3-2-2. In case of most doubtful part is BA Board 3-2-3. In case of most doubtful part is Panel module, T-con Board – 14 –...
Page 15
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 3-2-4. In case of most doubtful part is BA Board – 15 –...
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 SECTION 4 DISASSEMBLY Note: 1) The illustrations provided in this section might have slight difference from actual sets. 2) Refer to Removal & Installation of Rear Cover and Switch Unit Procedure in Section 1 Safety Notes. 4-1.
Page 17
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 4-1-8. Panel Removal 4-1-7. Speaker, HSN and HL1A boards Removal 1 Harness with connector 1 Speaker (4.2 X 15.5cm) 3 Remove connector 2 One screw 4 HSN board (+BVTP 3 X 12) 2 LCD panel 5 Guide, IR (C) 6 Remove connector...
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 4-4. KLV-52V550A 4-4-1. Rear Cover Removal 4-4-2. Stand Assy Removal 1 Four screws (+PSW M5 X 16) Four screws (+PSW M4 X 12) 2 Stand assy One screw (+BVTP 3 X 12) Twenty screws 3 One screw (+BVTP2 4 X 16)
Page 21
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 4-4-7. BA Board Removal 4-4-8. Frame Removal 1 Bracket Side Jack 1 Frame Vesa Top (52) 2 One screw (+BVST 3 X 8) 2 Nine screws (+BVST 3 X 8) 3 Frame, G 5 Frame, Center 4 Two screws 4 BA board...
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 SECTION 5 CAUTION : WIRE DRESSING 1. Do not overpull the wires during dressing --> avoid disconnection of wires. 2. Make sure wires are kept away from sharp edges, heatsinks & other high-temperature parts.
Page 23
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-1-3. P.3 Area SHEET(CORE)C 1-910-053-97 Make sure wire and Sheet Core(C) are not at clear panel area. Pull wire to this direction. HL1A Board Process the harness through the slit. 5-1-4. P.4 Area SHEET(CORE)C 1-910-053-97 HSN Board...
Page 24
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-1-5. P.5 Area CLAMP SHEET(CORE)C 1-910-053-97 CLAMP Pull wire to this direction Make sure speaker wire away from screw boss. To prevent sandwiched by Rear Cover during installation. 5-1-6. P.6 Area 1-910-053-97 Push in the direction of the arrow.
Page 25
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-1-7. P.7 Area CLAMP Power Unit SHEET(CORE)C 1-910-053-99 5-1-8. P.8 Area Apply Sheet Core(C) at first slit from LVDS. 1-910-053-99 CLAMP SHEET(CORE)C Don't let wire loose – 25 –...
Page 26
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-1-9. P.9 Area T-CON Salient under T-con The fourth position from the right LVDS SHEET(CORE)C CLAMP Tape, Electric Conduction(QT2) CLAMP Cover Tape, Electric Conduction with Sheet(core)C more than the half. 5-1-10. P.10 Area Power Unit Install SHEET(CORE)A to CORE ForTaiwan only...
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-2. KLV-40 V530A, V550A, V550A/R, V550A/W 5-2-1. Wire Dressing Overview ◊ Note: For details of each area dressing, refer to area information 5-2-2. P.2 Area Please fix the harness Balancer at a position of UL TAPE HSW3 Board About the harness processing to H1SW Board...
Page 28
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-2-3. P.3 Area 1-910-053-94 SHEET(CORE)C Make sure wire and Sheet Core(C) are not at clear panel area. SHEET(CORE)C Prevention of insertion of the harness by rear cabinet. Pull speaker wire away from speaker screw boss.
Page 29
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-2-5. P.5 Area 1-910-053-94 Push in the direction of the arrow. Put the habit on the lead. Make sure H wire is beneath the power wire. Please install Cushion D to H lead. (Side:30xLength:40) BA Board CLAMP...
Page 30
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-2-7. P.7 Area SHEET(CORE)A MV HARNESS Make sure wire is straight. Make sure wire is straight. Balancer CLAMP IP1 Board 1-910-053-96 SHEET(CORE)C 5-2-8. P.8 Area T-CON Install LVDS clamp to panel as shown. Otherwise, LVDS CLAMP LVDS cable suffers stress to connector.
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-3. KLV-46V550A 5-3-1. Wire Dressing Overview ◊ Note: For details of each area dressing, refer to area information 5-3-2. P.2 Area Please fix the harness at a position of UL TAPE Balancer HSW3 Board About harness processing to H1SW...
Page 33
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-3-3. P.3 Area 1-910-053-91 Please Wire harness and SHEET(CORE)C avoid a clear panel area. SHEET(CORE)C Prevention of insertion of the harness by rear cabinet. Pull wire to this direction. HL1A Board Process the harness through the slit.
Page 34
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-3-5. P.5 Area 1-910-053-91 BA Borad CLAMP 5-3-6. P.6 Area Push in the direction of the arrow. Put the habit on the lead. 1-910-053-91 IP2 Board 1-910-053-92 BA Board Make sure H wire is beneath the power wire.
Page 35
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-3-7. P.7 Area Balancer Make sure wire is straight Make sure wire is straight HV HARNESS SHEET(CORE)A IP2 Board 1-910-054-12 SHEET(CORE)C 5-3-8. P.8 Area T-CON LVDS CLAMP SHEET(CORE)C CLAMP BA Board –...
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-4. KLV-52V550A 5-4-1. Wire Dressing Overview P.11 P.10 P.7 P.8 P.12 Note: For details of each area dressing, refer to area information 5-4-2. P.2 Area Please fix the harness at a Balancer position of UL TAPE HSW3 Board...
Page 38
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-4-3. P.3 Area 1-910-054-00 Please avoid a clear panel area. Pull wire to this direction. SHEET(CORE)C HL1A Board Dress wire at slit (3x) 5-4-4. P.4 Area SHEET(CORE)C 1-910-054-00 CLAMP Please avoid frame area to hit the screw later HSN Board Pull speaker wire away from speaker screw boss.
Page 39
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-4-5. P.5 Area Push in the direction of the arrow. Put the habit on the lead. 1-910-054-00 1-910-054-01 Power Unit Make sure H wire is beneath the power wire. Please install Cushion D to H lead. (Side: 30mm x Length:40mm) BA Board CLAMP...
Page 40
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-4-7. P.7 Area Make sure electric harness is on top of other wires. CLAMP 1-835-715-11 1-836-138-11 1-910-054-02 Make sure electric harness is on top of other wires and avoid touching coil. Power Unit D5N Board 1-910-054-02...
Page 41
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-3-9. P.9 Area D6N Board CLAMP 1-836-138-11 1-910-054-13 CLAMP 5-3-10. P.10 Area Balancer HV HARNESS Make sure wire is straight SHEET(CORE)C D6N Board process the harness straight – 41 –...
Page 42
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 5-4-11. P.11 Area T-CON Install LVDS clamp to panel as shown. Otherwise, LVDS LVDS cable suffers stress to connector. Don't add a stress to the connector of the LVDS cable. CLAMP SHEET(CORE)C SHEET(CORE)C Do not enter Board.
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 SECTION 6 SERVICE ADJUSTMENTS 6-1. Viewing Service Adjustment Data 6-3. Accessing Diagnostic Menu There are no adjustments necessary for these models. 1. While TV on standby, press the following sequence on the All data have been set for optical viewing for customers.
KLV-32, 40 V530A, 32, 40, 46, 52 V550A RM-GA015 7-4. SCHEMATIC DIAGRAM 7-5. PRINTED WIRING BOARDS Board Function Note HDMI(EQ SW), VIDEO SW, SUB CHROMA, POWER(EMMA), CLK/ PERIPHERAL, ROM-IF/ STRAPS, DDR2, ETHERNET/USB, VIDEO IN/OUT, HDMI/PANEL OUT, AUDIO IN/OUT, STANDBY_MICRO Due to complexity of the board, performing component (MIMAS), POWER, level field repairs are not recommended.
Page 53
1-487-234-11 SWITCH UNIT A-1660-720-A IP1 COMPL 64 ! 1-822-147-11 AC INLET ! 1-822-617-11 AC INLET FILTER 4-103-642-21 EMBLEM, SONY NO.8 (Except KLV-40V550A/W) 2-661-171-01 SPRING, PANEL (KLV-40V550A(Tunisia, Russia)) 2-682-457-01 SPRING, PANEL(26) Note: The components identified by mark contain (KLV-40V550A(Tunisia, Russia)) confidential information. Strictly follow the instructions whenever the components are repaired and /or replaced.
Page 55
* A-1660-728-A IP2 COMPL 64 ! 1-822-147-11 AC INLET ! 1-822-617-11 AC INLET FILTER 2-635-749-11 EMBLEM, SONY NO.9 Note: The components identified by mark contain confidential information. Strictly follow the instructions whenever the components are repaired and /or replaced. – 55 –...
Page 57
AC INLET FILTER(KLV-52V550A(Russia, Tunisia)) * A-1663-196-A D5N COMPL * A-1663-200-A D6N COMPL 4-129-446-01 FRAME, VESA TOP(52) 2-635-749-11 EMBLEM, SONY NO.9 2-661-200-01 SPRING, PANEL(KLV-52V550A(Russia)) Note: The components identified by mark contain confidential information. Strictly follow the instructions whenever the components are repaired and /or replaced.
Page 63
Introduction Trademark information Thank you for choosing this Sony product. HDMI, the HDMI logo and High- Before operating the TV, please read this Definition Multimedia Interface are manual thoroughly and retain it for future trademarks or registered trademarks of reference.
Page 64
Table of Contents Usin Start-up Guide Safety Information ..........................8 Precautions ............................9 Remote and TV Controls/Indicators ....................10 Watching TV Watching TV ............................15 Using the Favourite List ........................17 Usin Using Optional Equipment Connecting Optional Equipment ....................18 Viewing Pictures from Connected Equipment ................20 Playing back Photo/Music/Video via USB ..................21 Using BRAVIA Sync with Control for HDMI..................22 Usin...
Start-up Guide Before Use 1: Attaching the stand (For KLV-46/40/32V550A/ To check the accessories KLV-40/32V530A) AC power cord (For KLV-52/46/40V550A/ KLV-40V530A) Cable holder (1) (For KLV-52/46/40V550A/ KLV-40V530A) Stand (1) and screws (4) (For KLV-46/40/32V550A/ KLV-40/32V530A) Remote RM-GA015 (1) Size AA batteries (R6 type) (2) To insert batteries into the remote Push and lift the cover to open.
Page 66
(not screw with a strong cord (not supplied). supplied) • An optional Sony support belt kit is used to secure S-Video the TV. Contact your nearest Sony service centre cable to purchase a kit. Have your TV model name (not ready for reference.
Page 67
4: Bundling the cables 5: Performing the initial set-up KLV-52V550A/46V550A/ 40V550A/KLV-40V530A * The shapes of mains plug/AC power plug and mains socket/AC power outlet differ depending on the region. Follow the instructions on the screen. • Do not bundle the mains lead/AC power cord Location: Select “Home”...
Page 68
Adjusting the viewing angle Detaching the Table-Top of the TV Stand from the TV This TV can be adjusted within the angles shown below. • Remove the screws guided by the arrow marks of the TV. Adjust the angle left and right (swivel) •...
– Keep the AC power cord away from • It is strongly recommended that you use carry out wall installations. a Sony wall-mount bracket in order to heat sources. • For safety reasons, it is strongly provide adequate air-circulation. recommended that you use Sony –...
Mercury is sometimes contained depending on the kind of following problems occur. fluorescent tubes. Follow your local Ask your dealer or Sony service centre to ordinances and regulations for disposal. have it checked by qualified service Handling and cleaning the personnel.
Remote and TV Controls/Indicators Remote and TV controls Buttons on the TV will work the same as those on the remote. * In the TV menu, these buttons will work as • The number 5, N, PROG + and AUDIO buttons on the remote have a tactile dot.
Page 72
6 RETURN Press to return to the previous screen of the displayed menu. When playing a photo/music/video file: Press to stop the playback (the display returns to the file or folder list). 7 PROG +/–/ In TV mode: Press to select the next (+) or previous (–) channel.
Page 73
qg Coloured In Text mode: When the coloured buttons are buttons available, an operation guide appears on the screen. qh Number In TV mode: Press to select channels. For buttons channel numbers 10 and above, press the next digit quickly. In Text mode: Press to enter a page number.
Page 74
• When you change the “Scene Select” setting, Theatre Mode turns off automatically. • “Control for HDMI” (BRAVIA Sync) is only available with the connected Sony equipment that has the BRAVIA Sync or BRAVIA Theatre Sync logo or is compatible with control for HDMI.
Page 75
Indicators Indicator Description 1 Light sensor Do not put anything over the sensor, doing so may affect its function. (page 24) 2 Remote control Receives signals from the remote. sensor Do not put anything over the sensor. The sensor may not work properly. (Picture Off / Lights up in green when you select “Picture Off”...
Watching TV To access Text Watching TV Press /. Each time you press /, the display changes cyclically as follows: Text and TV picture t Text t No Text (exit the Text service) To select a page, press the number buttons or To hold a page, press To reveal hidden information, press •...
Page 77
To change the Wide Mode manually Press repeatedly to select the desired Wide Mode. Wide Zoom* Enlarges the centre portion of the picture. The left and right edges of the picture are stretched to fill the 16:9 screen. Normal Displays the 4:3 picture in its original size.
Using the Favourite List Favourites The Favourite feature lets you select programmes from a list of up to 16 favourite channels that you specify. Press Perform the desired operation as shown in the following table or displayed on the screen. Favourite List Do this Watch a channel...
Using Optional Equipment Connecting Optional Equipment You can connect a wide range of optional equipment to your TV. Digital still camera Not available for KLV-40/ Camcorder 32V530A USB storage media Hi-Fi audio equipment Camcorder Headphones Home theatre system DVD player with Audio system component output Video game...
Page 80
PC/HDMI 1 AUDIO IN socket/jack in the PC IN sockets/jacks. • Be sure to use only an authorized HDMI cable bearing the HDMI logo. We recommend that you use a Sony HDMI cable (high speed type). 1 or 2...
The picture from the connected PC or Viewing Pictures from equipment is displayed in full size and the TV programme is displayed in the bottom Connected Equipment right corner. Turn on the connected equipment, then The sub screen picture is framed in gray perform the following operation.
Frame Image” and press The data on the USB device may be damaged. • Sony will not be held liable for any damage to, or Press RETURN repeatedly to return to loss of, data on the recording media due to a the Home Menu.
• Adjusts the volume (2 +/–) and mutes the sound (%) of a connected audio system. • You can operate the connected Sony equipment that has the BRAVIA Sync logo by the TV remote by pressing: – N/x/X/m/M to operate the connected equipment directly.
Using Menu Functions Navigating through TV Home Menu on XMB™ The XMB™ (XrossMediaBar) is a menu of BRAVIA features and input sources displayed on the TV screen. The XMB™ is an easy way to select programmes and adjust settings on your BRAVIA TV. Press HOME to display the XMB™.
TV Settings Menu System Update Used to update the TV’s system software in the future. Clock/Timers Sleep Timer Sets the TV to automatically switch to standby mode after a certain amount of time. When “Sleep Timer” is activated, the (Timer) indicator on the TV front panel lights up in orange.
Page 86
Picture Mode Sets a picture mode. The options that can be selected differ depending on the scene select settings. Vivid Enhances picture contrast and sharpness. Standard For standard pictures. Recommended for home entertainment. Custom Allows you to store your preferred settings. Cinema For viewing film-based content.
Page 87
Advanced Settings Allows you to set “Picture” settings in more detail. These settings are not available when “Picture Mode” is set to “Vivid” (or “Photo-Vivid”). Reset Resets all the advanced settings to the factory settings. Black Corrector Enhances black areas of the picture for stronger contrast. Adv.
Page 88
Surround Allows you to select the suitable surround effects depending on the genre of TV programme (movie, sport, music, etc.) or video game. The options that can be selected differ depending on the “Scene Select” settings. S-FORCE Front Delivers surround effects that help you enjoy the virtual Surround multi-ch surround audio with just the two internal TV speakers.
Page 89
4:3 Default Sets the default Wide Mode for 4:3 broadcasts. Wide Zoom Enlarges the 4:3 picture to fill the 16:9 screen, keeping the original image as much as possible. Normal Displays conventional 4:3 broadcasts in the correct proportion. Uses the setting that you specified in “Wide Mode”. Display Area Adjusts the picture display area.
Page 90
Audio Settings Speaker TV Speaker Turns on and outputs the TV’s sound from the TV speakers. Audio System Turns off the TV speakers and outputs the TV’s sound from external audio equipment connected to the audio output sockets/jacks on the TV. You can also turn on the connected equipment that is compatible with control for HDMI, after making the appropriate settings of control for HDMI.
Page 91
HDMI. When set to “On”, the following functions are available. If the specific Sony equipment that is compatible with control for HDMI is connected, this setting is applied to the connected equipment automatically when the “Control for HDMI”...
Page 92
Favourite Set-up Allows you to set your favourite channels by assigning the desired channel numbers. To reset the favourite channels, select “– – –”. Auto Tuning Tunes in all the available channels. You can retune the TV after moving house, or to search for newly launched channels.
Page 93
Allows you to fine-tune the selected channel manually if you feel that a slight tuning adjustment may improve picture quality. When “On” is selected, fine tuning adjustments are made automatically. Audio Filter Improves the sound of individual channels when distortion occurs in mono broadcasts in TV system “B/G”, “I”...
Installing the Accessories (Wall-Mount Bracket) To Customers: For product protection and safety reasons, Sony strongly recommends that installing of your TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself. To Sony Dealers and Contractors: Provide full attention to safety during the installation, periodic maintenance and examination of this product.
Page 95
KLV-40V550A/ KLV-40V530A KLV-32V550A/ KLV-32V530A Figures in the above table may differ slightly depending on the installation. WARNING The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of...
Page 96
SU-WL500 SU-WL50B SU-WL500 SU-WL50B KLV-52V550A/KLV-46V550A/KLV-40V550A/ d, g d, i KLV-40V530A KLV-32V550A/KLV-32V530A e, g e, h SU-WL500: Screw location Hook location When installing the Mounting Hook on the TV. When installing the TV onto the Base Bracket. * Hook location “a” cannot be used for the models in the table above.
Specifications Model name KLV-32V550A KLV-40V550A KLV-46V550A KLV-52V550A KLV-32V530A KLV-40V530A System Panel system LCD (Liquid Crystal Display) Panel TV system B/G, I, D/K, M Colour/video system PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video input) Channel coverage B/G: VHF: E2 to E12 / UHF: E21 to E69 /CATV: S01 to S03, S1 to S41...
Page 98
PC input signal reference chart for PC and HDMI IN 1, 2, 3, 4 (HDMI IN 4: KLV-52/46/40/ 32V550A only) Resolution Horizontal Vertical Standard Signals Horizontal × Vertical frequency (kHz) frequency (Hz) (Pixel) (Line) × 31.5 VESA × 37.5 VESA ×...
For example, the indicator may flash three times, go off for two seconds, then flash again three times. Press 1 on the TV to turn it off, disconnect the mains lead, and inform your dealer or Sony service centre of how the indicator flashes (number of flashes).
Page 100
HDMI, you cannot select “Off” in this menu. If you want to change the audio output to the TV speaker, select “TV Speaker” in the “Speaker” menu (page 29). Not all channels are tuned for • Check the support website for cable provide information. cable. http://www.sony-asia.com/bravia/flash.html...
Page 101
Instructions on “Installing the Wall-Mount Bracket” are not supplied in the form of a separate leaflet with this TV. These installation instructions are included within this TV’s instructions manual. Customer support Printed in Malaysia...