EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPOR- TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.
Page 4
y t i WARNING (UK Models only) The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 5 AMP rating. Should the fuse need to be replaced, use a 5 AMP FUSE approved by ASTA to BS 1362, ie one that carries the mark.
21 pin connector Rear Connection Panel Pin No Signal Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio output B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left) Output impedence : Less than 1kohm*...
The identification of errors within the FE-2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
2-1. Rear Cover Removal => => => Release the mains power cable from its securing posts. Remove the rear cover fixing screws indicated. Pull the rear cover away from the front beznet. Take care when removing the rear cover not to damage the speaker cables as speakers are fitted inside the rear cover.
2-4. A Board PWB Removal [ Step 1 ] Screw. Remove the screw securing the PWB to the main bracket. 2-6. Service Position Place the A Board PWB in the position indicated to carry out servicing. 2-5. A Board PWB Removal [ Step 2 ] Release the 5 securing clips located at the side and front of the chassis and slide the PWB clear of the bracket.
2-8. Picture Tube Removal WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.
• When complete readjustment is necessary or a new picture tube is installed, carry out the following adjustments. • Unless there are specific instructions to the contrary, carry out these adjustments with the rated power supply. • Unless there are specific instructions to the contrary, set the controls and switches to the following settings : Contrast 80% [or remote control normal]...
3-2. Convergence Preparation: Before starting this adjustment, adjust the focus, horizontal size and vertical size. Minimize the Brightness setting. Input a dot pattern from the pattern generator. Horizontal and Vertical Static Convergence Center dot V.STAT Vertical Static Magnet H STAT convergence control Fig.3-5...
Page 17
Geometry Adjustment. Preparation: Before starting this adjustment, adjust the horizontal and vertical static convergence. Remove the deflection yoke spacer. Tilt the deflection yoke as indicated in the figure below and optimise the geometry. Tilting the DY Up and Down will balance the upper and lower pin adjustment.
Layout of each control V.STAT Purity BMC (Hexapole) 3-3. Focus Adjustment Receive a television broadcast signal. Normalize the picture setting. Adjust the focus control located on the flyback transformer to obtain the best focus at the centre of the screen. Bring only the centre area of the screen into focus, the magenta-ring appears on the screen.
4-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied remote Commander RM-887 (KV-29LS30) or RM-932 (KV-29LS35). How to enter into the Service Mode Turn on the main power switch and enter into the stand-by mode. Press the following sequence of buttons on the Remote Commander.
Page 20
Sub Colour Adjustment Receive a PAL colour bar signal. Connect an oscilloscope to Pin 5 of CN003 [A Board]. Enter into the ‘Service’ service menu. Adjust the ‘Sub Colour’ data so that the Cyan, Magenta and Blue colour bars are of equal levels as indicated below. B-Out Waveform Tuner AGC Adjustment Note:...
4-2. TEST MODE 1: Test Mode 1 is available by pressing the ‘TEST’ button once, OSD ‘T’ appears. The functions described below are available by selecting the indicated keys. The ‘T’ is released automatically after each command is executed. i n i i n i i n i i n i...
5-1. BLOCK DIAGRAMS (2) CN703 R IN G IN TO A BOARD B IN CN504 IC701 CN1801 ROT - ROTATION ROT + NS CORRECT IC1801 ROTATION AMP RGB OUT J900 CN908 WOOFER MUTE AUDIO L OUT TO A BOARD CN208 AUDIO L IN J900 AUDIO R IN...
Page 25
C Board Waveforms C board Waveforms 20us/div 20us/div 10us/div 1.77 Vp-p (H) 1.88 Vp-p (H) 1.88 Vp-p (H) 20us/div 20us/div 20us/div 74 Vp-p (H) 74 Vp-p (H) 74 Vp-p (H) 20us/div 1.76 Vp-p (H) IC Voltage Table [ R,G,B OUT ]...
Page 28
NOTE: Portions of the circuit marked as shown are high voltage areas. Use care to prevent electric shock during inspection or repair. [ PRINTED WIRING BOARD ] Semiconductor Location Table Semiconductor Voltage Table IC Voltage Table...
Some delay should be anticipated when ordering these items. REMARK REF.NO. PART.NO *A-1632-925-A A BOARD, COMPLETE (KV-29LS30E/29LS30K) *A-1632-933-A A BOARD, COMPLETE (KV-29LS30U) *A-1632-932-A A BOARD, COMPLETE (KV-29LS35B) *A-1632-922-A A BOARD, COMPLETE (KV-29LS35E/29LS35K) 4-205-945-11 REAR COVER (KV-29LS30) 4-205-945-01 REAR COVER (KV-29LS35)
F2 BOARD COMPLETE Parts List : A BOARD COMMON Parts List : A BOARD VARIANT Parts List : Model KV-29LS30 KV-29LS35 C BOARD COMPLETE Parts List : VM BOARD COMPLETE Parts List : H2 BOARD COMPLETE Parts List : MISCELLANEOUS : ACCESSORIES AND PACKAGING MATERIALS : ...
Page 37
S2601 £ 1-571-433-31 SWITCH, PUSH (AC POWER) < VARISTOR > VDR2601 1-803-830-31 VARISTOR (ERZV14D621) *A-1632-925-A A Board, Complete (KV-29LS30E/ *A-1632-933-A A Board, Complete (KV-29LS30U) *A-1632-932-A A Board, Complete (KV-29LS35B) *A-1632-922-A A Board, Complete (KV-29LS35E/ A Board Common Parts 1-900-903-72 LEAD ASSY, FOCUS...
Page 41
REF.NO. PART.NO DESCRIPTION < IC > IC001 8-759-837-20 IC TDA9394H/N1/4/0310 IC004 8-759-575-72 IC M24C08-WMN6T IC401 8-759-665-11 IC LM393DT IC501 8-759-192-71 IC STV9379 IC531 8-759-665-11 IC LM393DT IC601 8-759-670-30 IC MCZ3001D IC602 8-749-016-19 IC SE135N-LF4 IC604 8-759-668-87 IC BA41W12ST-V5 IC608 8-759-591-02 IC L78L33ABZ-AP IC609 8-759-468-89 IC TOP209P IC1201...
Page 42
REF.NO. PART.NO DESCRIPTION JR21 1-216-295-91 SHORT JR24 1-216-295-91 SHORT JR25 1-216-295-91 SHORT JR26 1-216-295-91 SHORT JR101 1-216-295-91 SHORT JR419 1-216-295-91 SHORT JR423 1-216-296-91 SHORT JR508 1-216-295-91 SHORT JR601 1-216-295-91 SHORT JR609 1-216-295-91 SHORT JR610 1-216-295-91 SHORT JR1209 1-216-295-91 SHORT R003 1-216-065-91 RES-CHIP 4.7K 5% R004...
Page 49
With the optional IR Add-on kit, the following features can be added: Remote Commander emulation User programmable Functional Check through Infrared Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.