TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, THESE COMPONENTS WITH SONY PARTS WHOSE PART NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT SUPPLEMENTS PUBLISHED BY SONY.
Page 3
. s l . s l . s l . s l n i l e i l n i l i n i y t i - 3 -...
21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio output B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left) Output impedence : Less than 1kohm*...
FE-2 SELF DIAGNOSTIC SOFTWARE The identification of errors within the FE-2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal <= => <= => => Release the mains power cable from its securing posts. Remove the rear cover fixing screws indicated. Pull the rear cover away from the front beznet. 2-2. Chassis Removal and Refitting When refitting the chassis ensure that the main bracket is located in the beznet guide slots before sliding the chassis forwards.
2-3. A Board PWB Removal [ Step 1 ] 2-4. A Board PWB Removal [ Step 2 ] Clip. Screw. Remove the screw securing the PWB to the main bracket. Release the 5 securing clips located at the side and front of the chassis and slide the PWB clear of the bracket.
2-7. Picture Tube Removal WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.
SECTION 3 SET-UP ADJUSTMENTS • Carry out the adjustments in the following order : When complete readjustment is necessary or a new picture 3-1. Beam Landing. tube is installed, carry out the following adjustments. 3-2. Convergence. • Unless there are specific instructions to the contrary, carry 3-3.
If the V.STAT magnet is moved in the direction of the (a) 3-2. Convergence and (b) arrows, the Red, Green and Blue points move as indicated below. Preparation: • Before starting this adjustment, adjust the focus, horizontal size and vertical size. •...
Page 17
Geometry Adjustment. YCH Adjustment Preparation: YCH VR Before starting this adjustment, adjust the horizontal and Deflection Yoke vertical static convergence. Remove the deflection yoke spacer. Tilt the deflection yoke as indicated in the figure below and TLV Adjustment optimise the geometry. Tilting the DY Up and Down will balance the upper and lower pin adjustment.
Layout of each control 3-4. Screen (G2), White Balance [Adjustment in the service mode using the remote commander] G2 adjustment Input a dot signal from the pattern generator. Enter the ‘Service Mode’ by pressing ‘TEST’, ‘TEST’ and ‘38’ (TT-38) on the remote commander, to set up the G2 V.STAT service adjustment mode.
SECTION 4 CIRCUIT ADJUSTMENTS 4-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied remote Commander RM-947. How to enter into the Service Mode Turn on the main power switch and enter into the stand-by mode. Press the following sequence of buttons on the Remote Commander.
Page 20
Sub Colour Adjustment Deflection System Adjustment Enter into the ‘Geometry’ service menu. Receive a PAL colour bar signal. Select and adjust each item in order to obtain the optimum image. Connect an oscilloscope to Pin 5 of CN003 [A Board]. Enter into the ‘Service’...
4-2. TEST MODE 1: Test Mode 1 is available by pressing the ‘TEST’ button once, OSD ‘T’ appears. The functions described below are available by selecting the indicated keys. The ‘T’ is released automatically after each < > command is executed. y t i s i l i n i...
5-1. BLOCK DIAGRAMS (1) CN1201 CN605 IC001 R AUDIO MICRO, L AUDIO SPEAKERS VIDEO PROCESSOR, IC604 ROM, AUDIO, DUAL DC CN1200 VIDEO SWITCH REGULATOR +5V CN001 CN606 L IN AC IN XTAL IN MAIN RECT LINE FILTER R IN F2 BOARD PH601 X001 H2 BOARD...
5-1. BLOCK DIAGRAMS (2) 5-2. CIRCUIT BOARD LOCATION Reference Information CN707 TO A BOARD CN508 J701 IC701 RESISTOR : METAL FILM VIDEO AMP CN703 : SOLID R IN R IN G IN C Board FPRD : NON FLAMMABLE CARBON PICTURE TUBE G IN B IN TO A BOARD...
Page 25
A.-29LS40 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL JR505 A 4/4 A 3/4 STV9379 A 4/4 IC501 C516 L504 SMART PH2LF A 4/4 R045 H.DY- 1/10W CN512 1200V C582 JR508 150p CHIP A 4/4 R589 1200V R588 D502 CHIP R564...
Page 28
IC Voltage Table Semiconductor Voltage Table Semiconductor Location Table NOTE: Portions of the circuit marked as shown are high voltage areas. Use care to prevent electric shock during inspection or repair. ~ A Printed Wiring Board Conductor Side ~ - 28 -...
~ C Board Schematic Diagram [ RGB Out ] ~ ~ C Board Waveforms ~ C..-29LS40 CN704 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL 20us/div 20us/div 10us/div R,G,B OUT R728 R704 +200V 15MM 1/4W CN707 D704 D705 EL1Z 1.77 Vp-p (H) 1.88 Vp-p (H)
Page 30
~ C Printed Wiring Board Conductor Side ~ ~ H2 Printed Wiring Board Conductor Side ~ ~ VM Printed Wiring Board Conductor Side ~ ~ F2 Printed Wiring Board Conductor Side ~ - 30 -...
SECTION 6 EXPLODED VIEWS NOTE : Items with no part number and no description are not Items marked “*” are not stocked stocked because they are seldom required for routine since they are seldom required for service. routine service. Some delay should The construction parts of an assembled part are indicated be anticipated when ordering these items.
SECTION 7 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page A BOARD COMMON Parts List : Parts common to all models listed in this manual ...... 38 A BOARD VARIANT Parts List : PParts that belong only to the model specified Model KV-29LS40B ....................
Page 38
REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK * A-1052-332-A A Board Complete (KV-29LS40B) C215 1-163-084-00 CERAMIC CHIP 1.5PF 0.25PF 50V * A-1052-327-A A Board Complete (KV-29LS40E/K) C216 1-163-117-00 CERAMIC CHIP 100PF 5.00% 50V C217 1-163-084-00 CERAMIC CHIP 1.5PF 0.25PF 50V A Board Common Parts C218 1-216-295-91...
Page 49
• User programmable Functional Check through Infrared • Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.