hit counter script
Panasonic UF-585 Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Fax Machine
  5. Panafax UF-585
  6. Service manual
Panasonic UF-585 Service Manual

Panasonic UF-585 Service Manual

Hide thumbs Also See for UF-585:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , User Manual
Order Number : MGCS990301C1
H13
Facsimile
UF-585 / 595
© 1999 Matsushita Graphic Communication Systems, Inc.
All rights reserved. Unauthorized copying and distribution is
a violation of law.

Advertisement

Table of Contents
loading

Related Manuals for Panasonic UF-585

Summary of Contents for Panasonic UF-585

  • Page 1 Order Number : MGCS990301C1 Facsimile UF-585 / 595 © 1999 Matsushita Graphic Communication Systems, Inc. All rights reserved. Unauthorized copying and distribution is a violation of law.

  • Page 2: Table Of Contents

    Printer Unit Test ........56 Front Cover (104), Speaker (117), Separation Rubber (207) ......22 General Circuit Diagram......57 Control Panel Unit, SCA / SCB PCB (UF-595, UF-585)..59 PNL1 PC Board (231), LPC PCB ..........77 LCD Unit (233)........24 3.10 LCU PCB..........84 Transmit Guide (301) Assembly, 3.11 SRU PCB (Optional) ......
  • Page 3 Table of Contents Service Modes ........146 Options and Supplies ......262 Service Mode Table......146 Options and Supplies ......262 Service Mode 1 Installing Optional 250 Sheet Paper (Function Parameter Setting)....147 Cassette (UE-409070) ......263 Service Mode 3 (Printout of Lists, Installing Handset Kit (UE-403117) ..

  • Page 4: General Description

    1 General Description Overview This section covers the features and specifications of the plain paper facsimile transceiver "Panasonic UF-585/595". This fax machine can transmit and receive on the Public Switched Telephone Network (PSTN) in modes conforming to ITU-T Group 3 recommendations.
  • Page 5 General Description 12. Deferred Communication The 10 built-in 24-hour timers allow the operator to set deferred transmissions or deferred polling. Using the document memory, documents can also be transmitted to multiple stations. 13. Substitute Reception The contents of a document will be received into the document memory if the recording paper or toner runs out, or a recording paper jam occurs during reception.

  • Page 6: General Specifications

    Panasonic UF-585 / 595 26. Receive to Memory Users can set the unit to store incoming documents into its available memory. Later, using a 4-digit password, stored documents can be printed when the user is present. This function helps ensure that important documents are not read or lost while they are sitting unattended in the fax tray.

  • Page 7: General Description

    (using ITU-T Image No.1 in Standard Resolution) 12. Transmission Speed UF-585 : 6 Seconds using ITU-T Image No. 1 in Standard Resolution, memory to memory communication. UF-595 : 3 Seconds using ITU-T Image No. 1 in Standard Resolution, memory to memory communication.

  • Page 8: Scanner Specifications

    Panasonic UF-585 / 595 13. Automatic Dialing Dialing Signal 10 PPS/DTMF Dialing Method One-Touch Dialing Up to 28 keys (including 4 programmable keys) Abbreviated Dialing Up to 72 stations Manual Number Dialing Up to 12 stations (Direct Dialing) (Up to 36 digits including pauses)

  • Page 9: Printer Specifications

    203 dpi x 98 lpi (8 pels/mm 3.85 lines/mm) Fine 203 dpi x 196 lpi (8 pels/mm 7.7 lines/mm) S-Fine [UF-585] 203 dpi x 391 lpi (8 pels/mm x 15.4 lines/mm) [UF-595] 406 dpi x 391 lpi (16 pels/mm x 15.4 lines/mm) (Interpolated) 6.

  • Page 10: Power

    Panasonic UF-585 / 595 6. Printing Speed 5 ppm (12 seconds/page) 7. Fuser Warm Up Time Within 30 seconds after turning the power on. [Room Temperature: 68 to 95°F (20 to 35°C)] [Power Voltage: Minimum 115 VAC] 8. Document Tray Capacity...
  • Page 11 General Description 1.8.1 External View...
  • Page 12 Panasonic UF-585 / 595 1.8.2 Control Panel 6.9 inch...

  • Page 13: Specification Table

    General Description Specification Table Item UF-585 UF-595 Main Specification ← Compatibility ← PSTN Line Port Modem Speed (kbps) 14.4 - 2.4 33.6 - 2.4 ← Coding Scheme MH/MR/MMR ← ECM (Conforms to ITU-T) Yes(MMR) Short Protocol Yes (B) Yes (B,D) Transmission Speed Approx.
  • Page 14 Panasonic UF-585 / 595 Item UF-585 UF-595 Options ← Leased Line Port ← V.24 Line Port Cassette with Feeder Unit (250 sheets) ← Document Memory Yes (Flash Memory Card) (1MB/2MB/4MB) ← Page Memory ← Battery Backup 72 hours ← G3 Optional Communication Port ←...

  • Page 15: Function Table

    General Description 1.10 Function Table Item UF-585 UF-595 Dual Operation ← Multi-Task Operation ← Direct XMT Reserve ← Memory XMT Reserve ← Max. Number of Memory Job Files 10 files Dialing/Telephone Features ← One-Touch keys ← One-Touch/Program keys ← One-Touch Auto Dialers ←...
  • Page 16 Panasonic UF-585 / 595 Item UF-585 UF-595 ← Single Copy ← Multiple Copy ← Reduction Copy Certainty ← Verification Stamp ← Header/Total Page Print ← Transaction Journal Yes (32 transactions) ← Comm. Journal ← Last Ind. XMT Journal ← Power Failure Report List Printouts ←...
  • Page 17 Lithium Battery Paper Cassette (234) Recording Paper Tray SNS2 PC Board Assy (1007) (534) 2.21 Left Cover Right Cover (103) (102) Open Printer Cover Open Control Printer Cover Rear Cover Front Cover High Voltage PSU (104) Panel Unit (XXX) (XXX) (106) (424) LPC PC Board...

  • Page 18: Disassembly Instruction

    Disassembly Instruction Power Cord (1008), Telephone Line Cable (1009), Lithium Battery (234), Recording Paper Tray Assembly (1007), Paper Cassette (1) Remove the Battery Holder (230). (2) Release 2 Latch Hooks. (3) Remove the Lithium Battery (234). (4) Replace with a new Battery. Caution: Dispose of the Lithium Battery properly and keep it away from small children.

  • Page 19: Left Cover (103), Right Cover (102), Front Cover (104), Speaker (117

    Panasonic UF-585 / 595 Left Cover (103), Right Cover (102), Front Cover (104), Speaker (117), Separation Rubber (207) (1) Open the Printer Cover (106). (2) Open the Control Panel Unit. (3) Remove the Memory Card Cover (110). (Remove the Memory Card, if installed.) (4) 2 Screws (B1).
  • Page 20 Disassembly Instruction (11) Release 3 Latch Hooks. (12) Remove the Front Cover (104). (11) (12) Replacing & Cleaning Separation Rubber (1) Open the Control Panel Unit. (2) Open the Printer Cover (106). (3) Remove the Separation Rubber Holder Assy (202). (4) Replace with a new Separation Rubber (207).

  • Page 21: Control Panel Unit, Pnl1 Pc Board (231), Lcd Unit (233)

    Panasonic UF-585 / 595 Control Panel Unit, PNL1 PC Board (231), LCD Unit (233) (1) Open the Printer Cover (106) (2) Slightly open the Control Panel Unit. (3) Remove the Left Cover (103) and the Right Cover (102). (Refer to 2.3) (4) Disconnect Connector CN4 on the SCA/SCB PC Board.

  • Page 22: Lcd Unit (233)

    Disassembly Instruction (13) Disconnect the Flat Cable from the Connector CN41 on (15) (13) the PNL1 PC Board. (14) Release 3 Latch Hooks. (15) Remove the LCD Holder (223). (14) (16) Release 2 Latch Hooks. (17) Remove the LCD Unit (233). (16) (17)

  • Page 23: Transmit Guide (301) Assembly, Scanning Glass (308)

    Panasonic UF-585 / 595 Transmit Guide (301) Assembly, Scanning Glass (308) (1) Remove the Left Cover (103), Right Cover (102), and (4)x4 Front Cover (104) (Refer to 2.3). (2) Remove the Control Panel Unit (Refer to 2.4). (3) Release the Harnesses from the clamps.

  • Page 24: Stamp Assembly, Stamp Solenoid (327)

    Disassembly Instruction Stamp Assembly, Stamp Solenoid (327) (1) Remove the Transmit Guide (301) Assembly (Refer to 2.5). (2) Remove the Stamp Assembly (325, 326). (3) 1 Screw (19). (4) Remove the Stamp Solenoid (327).

  • Page 25: Eject Roller (303)

    Panasonic UF-585 / 595 Eject Roller (303) (1) Remove the Transmit Guide (301) Assembly (Refer to 2.5). (2) Remove the Stamp Assembly (325, 326) (Refer to 2.6). (3) Release 2 Latch Hooks. (4) Remove the Ground Plate (317). (5) Release the Latch Hook by using a small Blade-tip Screwdriver.
  • Page 26 Disassembly Instruction (10) Remove 2 P6A Bushings (316). (10) (11) Remove the Eject Roller (303). (11)

  • Page 27: Transmit Motor (324)

    Panasonic UF-585 / 595 Transmit Motor (324) (1) Remove the Transmit Guide (301) Assembly (Refer to 2.5). (2) Remove the Stamp Assembly (325, 326) (Refer to 2.6). (3) Disconnect the Harness (340) from the Transmit Motor. (4) Remove the ADF Gear (305) and ADF Angular Shaft (338).

  • Page 28: Scanner Block (321), Mirror 1 (334), Mirror 2 (335), Mirror 3 (336), Adf Roller (331)

    Disassembly Instruction Scanner Block (321), Mirror 1 (334), Mirror 2 (335), Mirror 3 (336), ADF Roller (331) (1) Remove the Transmit Guide (301) Assembly (Refer to 2.5). (2) Remove the Stamp Assembly (325, 326) (Refer to 2.6). (3) 1 Screw (19). (4) Remove the Harnesses from the hook.

  • Page 29: A4 Led Array (329), Feed Roller (302)

    Panasonic UF-585 / 595 2.10 A4 LED Array (329), Feed Roller (302) (1) Remove the Scanner Block (321) (Refer to 2.9). (2) Remove the Ground Plate (317). (3) 3 Screws (19). (4) Release the Harness from the hook. (5) Remove the LED Bracket (306) Assembly.

  • Page 30: Lpc Pc Board

    Disassembly Instruction 2.11 LPC PC Board (401), SCA/SCB PC Board (422), ILS PC Board (425), SNS4 PC Board (729) (1) Remove the Left Cover (Refer to 2.3). (2) Disconnect all Connectors on LPC PC Board (401). (3) Release Connectors CN50 and CN67 with your finger as shown in the illustration.

  • Page 31: High Voltage Power Supply Unit (424)

    Panasonic UF-585 / 595 2.12 High Voltage Power Supply Unit (424), Paper Feed Solenoid (531), Clutch Gear Assembly (530), Paper Feed Roller (518) (1) Remove the Right Cover (102) (Refer to 2.3). (2) Remove the HVPS Sheet (408). (3) 4 Screws (19).
  • Page 32 Disassembly Instruction Clean the Paper Feed Rollers (518) with a soft cloth, soaked with isopropyl alcohol. (15) 2 Screws (4N). (15) (16) Remove the Paper Feed Rollers (518). (16)

  • Page 33: Printer Cover (106), Rear Cover (105), Printer Motor (626)

    Panasonic UF-585 / 595 2.13 Printer Cover (106), Rear Cover (105), Printer Motor (626) (1) Remove the Left Cover and the Right Cover (Refer to 2.3). (2) Release the hooks and remove the Printer Cover (106). (3) 2 Screws (B1).

  • Page 34: Lcu Pc Board (402), Low Voltage Power Supply Unit (423)

    Disassembly Instruction 2.14 LCU PC Board (402), Low Voltage Power Supply Unit (423) (1) Remove the Rear Cover (105) (Refer to 2.13). (2) Remove the Flat Cable from the Connector CN25 on the LCU PC Board. (3) 3 Screws (B5). (4) Remove the LCU PC Board (402).

  • Page 35: Fuser Unit (701), Thermistor Assembly (728)

    Panasonic UF-585 / 595 2.15 Fuser Unit (701), Thermistor Assembly (728) CAUTION: To prevent getting burned, do not install, remove, clean or adjust when the Fuser Unit is hot. (1) Remove the Rear Cover (Refer to 2.13). (2) 1 Screw (19).

  • Page 36: Fuser Lamp (732), Exit Roller

    Disassembly Instruction 2.16 Fuser Lamp (732), Exit Roller (719), Fuser Roller (709), Pressure Roller (706) (1) Remove the Rear Cover (Refer to 2.13) and the Fuser Unit (Refer to 2.15). (2) 1 Screw (4N). (3) Remove the LVPS-Fuser Harness (727) and Fuser Lamp Terminal B (731).
  • Page 37 Panasonic UF-585 / 595 (10) Remove 2 Pressure Springs (708). (10) (11) Remove the E14 Gear (714). Caution: You may need to use force to pull out the Gear. (12) Remove the 2 E18 Gears (713). (14) (13) Remove 2 C-Rings (712).
  • Page 38 Disassembly Instruction (19) Remove 2 P6L5.5 Bushings (707). (20) Remove the Pressure Roller (706). Caution: Do not scratch the surface of the Pressure Roller when removing or reinstalling it. (20) (19)

  • Page 39: Rear Chassis (505), Prta Pc Board (536), Sns1 Pc Board (615)

    Panasonic UF-585 / 595 2.17 Rear Chassis (505), PRTA PC Board (536), SNS1 PC Board (615) (1) Remove the Fuser Unit (701) (Refer to 2.15). (2) 1 Screw (19). (3) Remove the Memory Card Ground Plate (516). (4) Remove the Parallel Port I/F Cover (113), Left and Right Printer I/F Brackets (405, 406) (Refer to 2.14).
  • Page 40 Disassembly Instruction (13) Disconnect Connectors CN80 and CN81on the SNS1 PC Board (615). (14) 1 Screw (19). (15) Remove the SNS1 PC Board (615). (13) (14) (15)

  • Page 41: Transfer Guide (601) Assembly, Feed Roller (526)

    Panasonic UF-585 / 595 2.18 Transfer Guide (601) Assembly, Feed Roller (526) (1) Remove the Rear Chassis (Refer to 2.17). (2) 2 Screws ( C8). (3) 1 Screw (19). (4) Disconnect Connector CN80 on the SNS1 PC Board (615). (5) Remove the Transfer Guide (601) Assembly.

  • Page 42: Toner Sensor (513), Laser Unit [Lsu] (512), Sns3 Pc Board (535)

    Disassembly Instruction 2.19 Toner Sensor (513), Laser Unit [LSU] (512), SNS3 PC Board (535) (1) Remove the Transmit Guide Assembly (Refer to 2.5). (2) 2 Screws (19). (3) Remove Ground Wire (542). (4) Remove the CCD Shield Plate (533). (5) 1 Screw (19). (6) Disconnect Connector CN84 on the SNS3 PC Board.
  • Page 43 Panasonic UF-585 / 595 (10) Disconnect 2 Connectors on the Laser Unit (512). (11)x4 (11) 4 Screws (1Y). (11) (11) (12) (12) Remove the Laser Unit (512). (10) (13) Disconnect Connectors CN83 and CN84 on the SNS3 PC Board (535).

  • Page 44: Bias Transfer Roller (604)

    Disassembly Instruction 2.20 Bias Transfer Roller (604) (1) Remove the CCD Shield Plate (Refer to 2.19). (2) 2 Screws (19). (3) Remove the BTR Guide (602). (4) Release the Latch Hook on the Transfer Guide (601) Black Assembly as illustrated and remove the Bias Transfer Roller (604).

  • Page 45: Sns2 Pc Board (534)

    Panasonic UF-585 / 595 2.21 SNS2 PC Board (534) (1) Place the machine on its rear side. (2) 1 Screw (19). (3) Remove the Plate A (507). (4) 1 Screw (19). (5) Remove the SNS2 PC Board (534). (6) Disconnect Connector CN82 (538) on the SNS2 PC Board.

  • Page 46: Printer Grease Points

    Disassembly Instruction 2.22 Printer Grease Points Before reassembling, apply EM-50L Grease to the parts shown in the illustration. (1) Gear G, B83D22 (622) : Gear surface (2) Gear B, D60D20 (621) : Rib surface (3) Gear F, D55 (619) : Gear surface (4) Gear F, D55 (619) : Gear Side surface...

  • Page 47: Screw Identification Template

    Panasonic UF-585 / 595 2.23 Screw Identification Template...

  • Page 48: Maintenance, Adjustments And Check Points

    Panasonic UF-585 / 595 3 Maintenance, Adjustments and Check Points Required Tools Tool Tool Soft Cloth Tweezer Isopropyl Alcohol Pliers Phillips Screwdriver (#2) Cotton Swab Stubby Phillips Screwdriver (#2) Brush Blade-tip Screwdriver (3/32 in) Molykote EM-50L Grease (Dow Corning) Periodic Maintenance Points...

  • Page 49: Periodic Maintenance Check List

    Maintenance, Adjustments and Check Points Periodic Maintenance Check List The chart outlined below is a general guideline for maintenance. The example list is for an average usage of 50 transmitted and received documents per day. Needless to say, the environmental conditions and actual use will vary these factors. The chart below is for reference only.

  • Page 50: Updating The Firmware

    1. Unplug the Power Cord to turn the machine OFF. 2. Install a Flash Memory Card (2 MB or higher) into the machine with the Panasonic Logo facing outwards. 3. Plug in the Power Cord to turn the machine ON.
  • Page 51 Maintenance, Adjustments and Check Points 3.4.4 Firmware Version UF-585 V10000 Country Code AU : USA AC : Canada Firmware Version Language A: US English, C-French & Spanish Firmware Type A : Standard B : Optional Model Number...

  • Page 52: Adf Pressure

    Panasonic UF-585 / 595 ADF Pressure • When documents multi-feed, move the pressure Adjusting Lever to the 3 (H) position. • When documents do not feed properly, move the Pressure Adjusting Lever to the 1 (L) position. Position Pressure of separator...

  • Page 53: General Circuit Diagram

    Maintenance, Adjustments and Check Points General Circuit Diagram 3.7.1 Fax Circuit...
  • Page 54 (422) (512) (424) (423) (401) FUSER LAMP (732) THERMOSTAT THERMAL FUSE THERMISTOR (728) PRINTER MOTOR FUSER UNIT (626) (701) (729) PAPER FEED SOLENOID (531) (615) (534) (535) (513) * OPTIONAL 2ND CASSETTE PAPER FEED SOLENOID (921) (908) (923)

  • Page 55: Sca / Scb Pcb (Uf-595, Uf-585)

    Maintenance, Adjustments and Check Points SCA / SCB PCB (UF-595, UF-585) CN10 CN11 F-ROM Pin No. Signal Name Destination Signal Waveform Function CN1-1 +24V LED Array +24 VDC Power Supply +24V CN1-2 nLEDON LED Array LED Enable Signal Approx.+13V(H) LED Off...
  • Page 56 Panasonic UF-585 / 595 Pin No. Signal Name Destination Signal Waveform Function CN2-4 nSBSY LPC PCB CN 50-4 Serial Interface Enable Signal +5V(H) 0V(L) CN2-5 nCMD LPC PCB CN 50-5 Serial Interface Command Data Signal +5V(H) 0V(H) CN2-6 nCBSY LPC PCB CN 50-6...
  • Page 57 Maintenance, Adjustments and Check Points Pin No. Signal Name Destination Signal Waveform Function CN3-1 +24V Stamp Solenoid +24 VDC Power Supply +24V CN3-2 Not Used CN3-3 nSTAMPON Stamp Solenoid Stamp Driver Signal +24V Stamp Off Stamp On Pin No. Signal Name Destination Signal Waveform Function...
  • Page 58 Panasonic UF-585 / 595 Pin No. Signal Name Destination Signal Waveform Function CN4-10 pBZCLK PNL PCB CN40-10 Buzzer Clock CN4-11 nWAKUP PNL PCB CN40-11 Power Saver Reset Signal CN4-12 nPWSAVE PNL PCB CN40-12 Power Saver Enable +5V(H) 0V(L) CN4-13 nBPNT...
  • Page 59 Maintenance, Adjustments and Check Points Pin No. Signal Name Destination Signal Waveform Function CN6-1 +24V LVPS CN33-1 +24 VDC Power Supply +24V CN6-2 +24V LVPS CN33-2 +24 VDC Power Supply +24V CN6-3 LVPS CN33-3 Ground CN6-4 LVPS CN33-4 Ground CN6-5 -12V LVPS CN33-5 -12 VDC Power Supply...
  • Page 60 Panasonic UF-585 / 595 Pin No. Signal Name Destination Signal Waveform Function CN7-1 FR CCD PCB CN30-1 Reset Signal +5V(H) 0V(L) CN7-2 FCK1 CCD PCB CN30-2 Shift Register Clock 1 1 s 1 s +5V(H) 0V(H) CN7-3 FCK2 CCD PCB CN30-3...
  • Page 61 Maintenance, Adjustments and Check Points Pin No. Signal Name Destination Signal Waveform Function CN8-4 pHKOF LCU PCB CN25-4 External Phone Off-Hook Detection Signal OFF Hook +5V (H) (Phone Line must be connected) H : Off Hook 0V (L) ON Hook L : On Hook CN8-5 pPLSD...
  • Page 62 Panasonic UF-585 / 595 Pin No. Signal Name Destination Signal Waveform Function CN9-1 pSPKOT Speaker Line Signal, Key Tone, Ringer CN9-2 GND Speaker Ground CN10 Note: CN212 is available when the Optional Parallel I/F is installed. Pin No. Signal Name...
  • Page 63 Maintenance, Adjustments and Check Points Pin No. Signal Name Destination Signal Waveform Function PRTA PRTA CN200 CN202 CN212 CN10-9 D9 Data Signal (9) +5V(H) 0V(L) CN10-10 D8 Data Signal (8) +5V(H) 0V(L) CN10-11 D7 Data Signal (7) +5V(H) 0V(L) CN10-12 D6 Data Signal (6) +5V(H) 0V(L)
  • Page 64 Panasonic UF-585 / 595 CN11 Note: CN212 is available when the Optional Parallel I/F is installed. Pin No. Signal Name Destination Signal Waveform Function PRTA PRTA CN201 CN202 CN212 CN11-1 GND Ground CN11-2 nWRH Write H Signal - Low Enable...
  • Page 65 Maintenance, Adjustments and Check Points Pin No. Signal Name Destination Signal Waveform Function PRTA PRTA CN201 CN202 CN212 CN11-12 nINT1 Data Transfer Interrupt Signal +5V(H) 0V(L) CN11-13 nINT0 Signal Detect Interrupt Signal +5V(H) 0V(L) CN11-14 pDRACK Not Used CN11-15 nDREQ Not Used CN11-16 pDACK Not Used...
  • Page 66 Panasonic UF-585 / 595 CN12 Pin No. Signal Name Destination Signal Waveform Function CN12-1 GND Flash Memory Card Ground CN12-2 D3 Flash Memory Card Data Signal (3) 5V(H) 0V(L) CN12-3 D4 Flash Memory Card Data Signal (4) 5V(H) 0V(L) CN12-4 D5...
  • Page 67 Maintenance, Adjustments and Check Points Pin No. Signal Name Destination Signal Waveform Function CN12-13 A14 Flash Memory Card Address Signal (14) 5V(H) 0V(L) CN12-14 A15 Flash Memory Card Address Signal (15) 5V(H) 0V(L) CN12-15 nWRL Flash Memory Card Write L Signal - Low Enable 5V(H) 0V(L) CN12-16 RDY / *BSY...
  • Page 68 Panasonic UF-585 / 595 Pin No. Signal Name Destination Signal Waveform Function CN12-25 A5 Flash Memory Card Address Signal (5) 5V(H) 0V(L) CN12-26 A4 Flash Memory Card Address Signal (4) 5V(H) 0V(L) CN12-27 A3 Flash Memory Card Address Signal (3)
  • Page 69 Maintenance, Adjustments and Check Points Pin No. Signal Name Destination Signal Waveform Function CN12-37 D11 Flash Memory Card Data Signal (11) 5V(H) 0V(L) CN12-38 D12 Flash Memory Card Data Signal (12) 5V(H) 0V(L) CN12-39 D13 Flash Memory Card Data Signal (13) 5V(H) 0V(L) CN12-40 D14...
  • Page 70 Panasonic UF-585 / 595 Pin No. Signal Name Destination Signal Waveform Function CN12-49 A21 Flash Memory Card Address Signal (21) 5V(H) 0V(L) CN12-50 GND Flash Memory Card Ground CN12-51 +5V Flash Memory Card +5 VDC Power Supply CN12-52 NC Flash Memory Card...
  • Page 71 Maintenance, Adjustments and Check Points Pin No. Signal Name Destination Signal Waveform Function CN12-63 ID1 Flash Memory Card Flash Memory Card ID CN12-64 D8 Flash Memory Card Data Signal (8) 5V(H) 0V(L) CN12-65 D9 Flash Memory Card Data Signal (9) 5V(H) 0V(L) CN12-66 D10...
  • Page 72 Panasonic UF-585 / 595 CN15 Pin No. Signal Name Destination Signal Waveform Function CN15-1 +24V LPC PCB CN15-1 +24 VDC Power Supply +24V CN15-2 +24V LPC PCB CN15-2 +24 VDC Power Supply +24V CN15-3 +24V LPC PCB CN15-3 +24 VDC Power Supply...

  • Page 73: Lpc Pcb

    Maintenance, Adjustments and Check Points LPC PCB CN58 CN59 CN57 CN66 CN53...
  • Page 74 Panasonic UF-585 / 595 CN50 Refer to SCA / SCB PCB CN2. CN53 Pin No. Signal Name Destination Signal Waveform Function CN53-1 +24VM HVPS +24 VDC Power Supply +24V CN39-1 CN53-2 nCR0 HVPS Charge Control AC Output +24V (H) CN39-2...
  • Page 75 Maintenance, Adjustments and Check Points CN54 Pin No. Signal Name Destination Signal Waveform Function CN54-1 nMMP0a Printer Motor Printer Motor Phase 1 Output Signal CN118-1 +24V(H) 0V(H) CN54-2 +24VM Printer Motor +24 VDC Power Supply +24V CN118-2 CN54-3 pMMP0a Printer Motor Printer Motor Phase 0 Output Signal CN118-3 +24V(H)
  • Page 76 Panasonic UF-585 / 595 CN57 Pin No. Signal Name Destination Signal Waveform Function CN57-1 +24V ILS PCB +24 VDC Power Supply +24V CN73-1 CN57-2 NC CN57-3 +24VD ILS PCB Printer Cover Detection Signal +24V (H) CN73-3 Cover Closed Cover Open...
  • Page 77 Maintenance, Adjustments and Check Points CN59 Pin No. Signal Name Destination Signal Waveform Function CN59-1 nPCHK1 SNS1 No Paper Sensor Detection Signal CN83-1 +5V (H) No Paper Paper 0V (L) CN59-2 LDSP1 SNS1 No Paper Sensor LED Drive Current CN83-2 Approx.
  • Page 78 Panasonic UF-585 / 595 Pin No. Signal Name Destination Signal Waveform Function CN66-7 nOP CST2 2nd Feeder Unit Detection Signal CN70-7 +5V (H) No Feeder Unit 0V (L) CN67 Refer to SCA / SCB CN15. CN68 Pin No. Signal Name...
  • Page 79 Maintenance, Adjustments and Check Points CN69 Pin No. Signal Name Destination Signal Waveform Function CN69-1 nPMCK Tetragon Motor Clock CN15-1 0.702 kHz (400 dpi) +5V(H) 1.076 kHz (600 dpi) 0V(H) CN69-2 nPMRY Tetragon Motor Ready Signal +5V (H) CN15-2 Not Ready Ready 0V (L) CN69-3 nPMON...

  • Page 80: Lcu Pcb

    Panasonic UF-585 / 595 3.10 LCU PCB CN25 LINE CN21 CN20...
  • Page 81 Maintenance, Adjustments and Check Points CN20 Pin No. Signal Name Destination Signal Waveform Function CN20-3 LT2(T) Telephone Line Line Signal CN20-4 LT1(R) Telephone Line Line Signal CN21 Pin No. Signal Name Destination Signal Waveform Function CN21-3 T1 External Telephone External Telephone Line Signal CN21-4 T2 External Telephone External Telephone Line Signal...

  • Page 82: Sru Pcb (Optional)

    Panasonic UF-585 / 595 3.11 SRU PCB (Optional) Handset CN91 TEL Cradle Cord CN90 Refer to LCU PCB CN23. CN91 Pin No. Signal Name Destination Signal Waveform Function CN91-1 NC Not Used CN91-2 MIC (+) Telephone Handset CN Handset Microphone...

  • Page 83: Low Voltage Power Supply Pcb (Pow)

    Maintenance, Adjustments and Check Points 3.12 Low Voltage Power Supply PCB (POW) CN33 CN31 L102 CN31 Pin No. Signal Name Destination Signal Waveform Function CN31-1 HEAT 1 Fuser Unit CN116 Fuser Lamp AC (Black-Live) CN31-2 HEAT 2 Fuser Unit CN116 Fuser Lamp AC (White-Neutral) CN33 Refer to SCA / SCB PCB CN6.

  • Page 84: High Voltage Power Supply Pcb (Hvps)88

    Panasonic UF-585 / 595 3.13 High Voltage Power Supply PCB (HVPS) T401 T301 T101 T201 High Voltage Output Pin No. Signal Name Destination Signal Waveform Function (1) Transfer Current: (+2.5 µA) Transfer Bias Transfer Roller (2) Cleaning Voltage: (-1500 V) Charge Current: 220 µA...

  • Page 85: Sns3

    Maintenance, Adjustments and Check Points 3.14 SNS3 CN84 CN83 CN83 Refer to LPC PCB CN59. CN84 Pin No. Signal Name Destination Signal Waveform Function CN84-1 GND Toner Sensor Ground CN84-2 TONER Toner Sensor Remaining Toner Level Signal Approx. +2 VDC CN84-3 +5V Toner Sensor +5 VDC Power Supply...

  • Page 86: Sns4

    Panasonic UF-585 / 595 3.15 SNS4 CN86 CN85 Pin No. Signal Name Destination Signal Waveform Function CN85-1 nCCHK1 SNS1 No Cassette Detection Signal CN81-1 CN85-2 GND SNS1 Ground CN81-2 CN85-3 nRSEN SNS1 Timing Sensor Detection Signal CN81-3 +5V (H) Detect Paper...

  • Page 87: Sns1

    Maintenance, Adjustments and Check Points 3.16 SNS1 CN80 CN81 CN80 Pin No. Signal Name Destination Signal Waveform Function CN80-1 nCCHK1 SNS2 No Cassette Detection Signal CN82-1 CN80-2 GND SNS2 Ground CN82-2 CN80-3 LDSC1 SNS2 No Cassette Sensor LED Drive Current CN82-3 Approx.

  • Page 88: Ccd Alignment

    Panasonic UF-585 / 595 3.18 CCD Alignment The CCD PC Board (337) is factory adjusted using special precision equipment and normally should not be replaced in the field. It is recommended that the entire Scanner Block (321) be replaced. This will insure that the CCD PC Board (337) is aligned properly.
  • Page 89 Maintenance, Adjustments and Check Points 5. Adjusting the CCD PC Board a. Enter Service Mode No. 5-1 (see Section 5.5.1 [CCD Test]). b. Monitoring the Oscilloscope, carefully adjust the position of the CCD Board until the output is obtained as shown below.
  • Page 90 Panasonic UF-585 / 595 APPENDIX CCD TEST PATTERN...

  • Page 91: Troubleshooting

    Panasonic UF-585 / 595 4 Troubleshooting Initial Troubleshooting Flowchart START Plug the Power Cord in to turn ON the unit. Does the unit power up normally? Does the LCD display function correctly? Troubleshoot Improper LCD Display (Sect. 4.2). Troubleshoot any 3-digit INFO.

  • Page 92: Improper Lcd Display

    Troubleshooting Improper LCD Display START Check connectors: CN4 (SCA/SCB PCB) and CN40 (PNL1 PCB). When pressing any key, do you hear the 'Pi-' sound from the Speaker? Does CN4, pin 2 and pin 3 on the SCA/SCB PCB measure +5VDC? Replace the PNL1 PCB.

  • Page 93: Information Codes (Info. Codes)

    Panasonic UF-585 / 595 Information Codes (INFO. CODES) The 3-digit information codes display to show the unit’s status. These codes also print on the journal. The following table indicates appropriate sections for troubleshooting. Code Explanation Phase Section Recording paper jam 4.3.8...
  • Page 94 Troubleshooting 4.3.1 Information Codes: 400, 420 START START Enable the monitor speaker. Is reception from a reference (Refer to Sect. 5.2 Parameter unit successful? No. 008) Check the line connection from the wall jack to the "Line" on the LCU PCB. Perform a transmission test to the remote unit in question.
  • Page 95 Panasonic UF-585 / 595 4.3.2 Information Codes: 401, 402, 422...
  • Page 96 Troubleshooting 4.3.3 Information Codes: 404, 405, 407 START Is communication with reference unit successful? 1. Replace the LCU PCB. 2. Replace the SCA/SCB PCB. Change Function Parameter #010: Reduce Tx Attenuation Level Does the problem still occur? Does the problem still occur? Check the telephone line condition.
  • Page 97 Panasonic UF-585 / 595 4.3.4 Information Code: 416 START Is communication with the reference unit successful? 1. Replace the LCU PCB. 2. Replace the SCA/SCB PCB. Change Function Parameter #011: Reduce Rx Sensitivity Level Does the problem still occur? Does the problem still occur? Check the telephone line condition.
  • Page 98 Troubleshooting 4.3.5 Information Codes: 408, 409, 417, 418, 490...
  • Page 99 Panasonic UF-585 / 595 4.3.6 Information Code: 434 START Is communication with the reference unit successful? Replace the SCA/SCB PCB. Does the trouble occur regardless of the remote unit? Can the transmitter in question Check the remote unit in question.
  • Page 100 Troubleshooting 4.3.7 Information Codes: 459, 494, 495 START Check the line connection between the telephone jack on the wall and the LCU PCB. Is communication with the reference unit successful? 1. Replace the LCU PCB. 2. Replace the SCA/SCB PCB. Does the problem still occur? Check the telephone line condition.
  • Page 101 Panasonic UF-585 / 595 4.3.8 Information Codes: 001, 002, 007 (Recording Paper Jam) START Is the recording paper size and thickness within specification? Replace with correct paper. Is the recording paper loaded in the Cassette properly? Load the paper correctly.
  • Page 102 Troubleshooting 4.3.9 Information Code: 010 (No Recording Paper) START Is the Paper Cassette seated properly Reseat the cassette. Is the recording paper loaded in the cassette? Load the paper. Is the No Paper Actuator operational? Replace the Actuator. Is the No Paper Sensor operational? Replace the No Paper Sensor.
  • Page 103 Panasonic UF-585 / 595 4.3.10 Information Codes: 030, 031 (Document Jam)
  • Page 104 Troubleshooting 4.3.11 Information Code: 630 (Dialing Error) START Is there a dial tone when MONITOR button is pressed? 1. Connect the telephone line correctly. 2. Check the telephone line. Is the remote machine busy? Can the unit dial the reference unit? 1.
  • Page 105 Panasonic UF-585 / 595 4.3.12 Information Codes: 403, 411, 414, 415 (Polling Operator Trouble)

  • Page 106: Printed Copy Quality Problems

    Troubleshooting Printed Copy Quality Problems 4.4.1 Black Copy START Is the printout in Service Mode 3 normal? Check the Scanner mechanism. Is the Toner Cartridge operational? Replace the Toner Cartridge. Is the HVPS normal? 1. Check all connectors and voltages on the HVPS. 2.

  • Page 107: Blank Copy

    Panasonic UF-585 / 595 4.4.2 Blank Copy START Is the printout in Test Mode 3 normal? Check the Scanner mechanism. Is the Toner Cartridge operational? Replace the Toner Cartridge. Are there any foreign particles or stains on the BTR? 1. Clean the BTR with a soft, dry cloth.

  • Page 108: Vertical White Lines

    Troubleshooting 4.4.3 Vertical White Lines START Is the printout in Service Mode 3 normal? Check the Scanner mechanism. Is the recording paper damp? Replace the paper. Is the Toner Cartridge operational? Replace the Toner Cartridge. Are there any foreign particles or stains blocking the Laser Beam path? 1.

  • Page 109: Ghost Images

    Panasonic UF-585 / 595 4.4.4 Ghost Images A A A START Is the printout in Service Mode 3 normal? Check the Scanner mechanism. Is the recording paper damp? Replace the paper. Is the Toner Cartridge operational? Replace the Toner Cartridge.

  • Page 110: Vertical Dark Lines

    Troubleshooting 4.4.5 Vertical Dark Lines START Is the printout in Service Mode 3 normal? Check the Scanner mechanism. Is the Toner Cartridge operational? Replace the Toner Cartridge. Are there any foreign particles or stains on the BTR? 1. Clean the BTR with a soft, dry cloth.

  • Page 111: Horizontal Dark Lines

    Panasonic UF-585 / 595 4.4.6 Horizontal Dark Lines START Is the printout in Service Mode 3 normal? Check the Scanner mechanism. Is the Toner Cartridge operational? Replace the Toner Cartridge. Are there any foreign particles or stains on the BTR? 1.

  • Page 112: Dark Background

    Troubleshooting 4.4.7 Dark Background START Is the printout in Service Mode 3 normal? Check the Scanner mechanism. Is the recording paper damp? Replace the paper. Is the Toner Cartridge operational? Replace the Toner Cartridge. Is the LSU normal? Replace the LSU. Is the HVPS normal? 1.
  • Page 113 Panasonic UF-585 / 595 4.4.8 Light Print...

  • Page 114: Horizontal White Lines

    Troubleshooting 4.4.9 Horizontal White Lines START Is the printout in Service Mode 3 normal? Check the Scanner mechanism. Is the recording paper damp? Replace the paper. Is the Toner Cartridge operational? Replace the Toner Cartridge. Are there any foreign particles or stains on the BTR? 1.
  • Page 115 Panasonic UF-585 / 595 4.4.10 Improper Fusing (Printed image does not bond to the paper) START Is the recording paper damp? Replace the paper. Is the Fuser Unit normal? Replace the Fuser Unit. (See Note) Note Replace the entire Unit when the Thermostat or the Thermal Fuse becomes open-circuit.

  • Page 116: Voids In Solid Areas

    Troubleshooting 4.4.11 Voids in Solid Areas START Is the recording paper damp? Replace the recording paper. Is the Toner Cartridge operational? Replace the Toner Cartridge. Are the Fuser and Pressure Roller surfaces clean? Clean or replace the rollers.

  • Page 117: Black Dots

    Panasonic UF-585 / 595 4.4.12 Black Dots START Is the Toner Cartridge operational? Replace the Toner Cartridge. Are the Fuser and Pressure Roller surfaces clean? Clean or replace the rollers.

  • Page 118: Recording Paper Creases

    Troubleshooting 4.4.13 Recording Paper Creases START Is the recording paper damp? Replace the recording paper. Are there any foreign particles or stains in the paper path? Remove any obstructions and clean the paper path. Is the recording paper skewing? Ensure the paper is set under the Paper Separation Clips in the cassette.

  • Page 119: Poor Printed Copy Quality

    Panasonic UF-585 / 595 4.4.14 Poor Printed Copy Quality START Is the printout in Service Mode 3 normal? 1. Replace the LPC PCB. 2. Replace the LSU. 3. Replace the HVPS. 4. Replace the Toner Cartridge. Make a local copy.

  • Page 120: Abnormal Printing

    Is the recording paper size and thickness within specification? Replace with correct paper (Sect. 1.5). Is the Panasonic Toner Cartridge being used? Replace with the Panasonic Toner Cartridge. Are all switches and sensors operating properly? Adjust, clean or replace. Are there any foreign particles or...

  • Page 121: Scanned Copy Quality Problems

    Panasonic UF-585 / 595 4.4.16 Scanned Copy Quality Problems START Is the LED Array abnormal? Replace the LED Array. Are there any foreign particles or paper pieces in the scanning area? Remove the foreign particles or paper pieces from the scanning area.

  • Page 122: Document Feeder (Adf)

    Troubleshooting Document Feeder (ADF) 4.5.1 No Document Feed START Is the document set properly? Set the document properly. Is the document thickness or size within specification? Make a copy or cut the document to the specification size. Is the "Pi.." tone generated when the document is set? Does the ADF Sensor actuator move smoothly?

  • Page 123: Document Does Not Feed Or Multiple Feeds

    Panasonic UF-585 / 595 4.5.2 Document does not feed or Multiple feeds START Is the Control Panel Unit locked? Close the Control Panel Unit firmly. Is the adjustment of the Separation Rubber normal? Is the Separation Rubber worn out? Clean or adjust the Separation Rubber Pressure (Sect.
  • Page 124 Troubleshooting 4.5.3 Document Jam (030) or Skewing START Is the Control Panel Unit closed? Close the Control Panel Unit firmly. Do all sensors on the PNL1 PCB operate normally? Clean or replace the PNL1 PCB. Does the Feed Roller have drive and sufficient friction? Clean the surface of the roller with isopropyl alcohol (Sect.

  • Page 125: Communications

    Panasonic UF-585 / 595 Communications This section explains general troubleshooting procedures for the 400 series of Information Codes. These errors are primarily caused by poor telephone line quality (loss, noise, echo, etc.). This unit is furnished with Service Mode 1 to assist in troubleshooting line quality problems.

  • Page 126: Poor Transmitted Copy Quality

    Troubleshooting 4.6.2 Poor Transmitted Copy Quality START Make a copy. Is the printed copy normal? Is the LED Array lit? Does CN1, pin 1 on the SCA/SCB PCB measure +24 VDC? Replace the LVPS. Does nLEDON go Low when the scan starts? Replace the SCA/SCB PCB.

  • Page 127: Dialing Problems

    Panasonic UF-585 / 595 4.6.3 Dialing Problems START Does the unit proceed to Phase B? 1. Set documents on the ADF correctly. 2. Check the telephone line connection. 3. The called party is busy. 4. Refer to Sect. 4.6. Are you using One-Touch dialing or ABBR.

  • Page 128: Transmission Problems

    Troubleshooting 4.6.4 Transmission Problems START Does the ID display? 1. No ID function at the remote unit. 2. The ID is not set for the remote unit. Does the Verification Stamp operate? 1. Set "STAMP=ON" 2. Check CN3 (SCA/SCB PCB). 3.

  • Page 129: Reception Problems

    Panasonic UF-585 / 595 4.6.5 Reception Problems START Does the machine answer the Ringing signal? 1. Set "RCV = AUTO". 2. Check that all covers are closed firmly. 3. Check the telephone line connection. 4. Check the Ringer Timing or DRD setting.

  • Page 130: Polling Problems

    Troubleshooting 4.6.6 Polling Problems START Is Polling reception OK? 1. Set the same polling password as the other party is using. 2. Check the password of the remote unit. Is Polling transmission OK? 1. Set the polling password or no - check mode.* 2.

  • Page 131: Information Code Table

    Panasonic UF-585 / 595 Information Code Table Information Codes Code Mode Phase Description of Problem Cause Leading edge of the recording paper fails to Recording paper jam. COPY reach the Timing Sensor. (1st cassette) Timing Sensor abnormal. Leading edge of the recording paper fails to Recording paper jam.
  • Page 132 Troubleshooting Information Codes Code Mode Phase Description of Problem Cause DCN was returned from receiver while Receiver working in non-CCITT mode only. transmitter is waiting for NSF/DIS. (Possible incompatibility) RCV(Polling) Transmitter had no polling function. "POLLED=ON" (polling XMT ready) is not set at the transmitter.
  • Page 133 Panasonic UF-585 / 595 Information Codes Code Mode Phase Description of Problem Cause XMT or RCV CD (response from Modem) did not turn OFF Remote unit is defective. within 180 sec. after receiver detected FLAG SCA/SCB PCB or LCU PCB is defective.
  • Page 134 Troubleshooting Information Codes Code Mode Phase Description of Problem Cause Redial count over with no response from the called station or busy tone was not detected. Note: If busy tone is not detected, the machine will only redial once. Power turned off with applicable data in memory Power cord unplugged.

  • Page 135: Diagnostic Codes

    Panasonic UF-585 / 595 Diagnostic Codes The 13-digit Diagnostic Code is provided for the service engineer to analyze how the communication was performed. The code is recorded on the Journal. Journal Example ************* -JOURNAL- ************************* DATE MAR-12-1999 ***** TIME 09:39******** NO.
  • Page 136 Troubleshooting 3rd Digit -: Not used/defined Data Definition Resolution Paper Width S-Fine 400 x 400 300 x 300 4th Digit -: Not used/defined Data Definition Scanning Rate Resolution 20 ms/line 5 ms/line 10 ms/line 40 ms/line 0 ms/line 20 ms/line Fine 5 ms/line Fine...
  • Page 137 Panasonic UF-585 / 595 6th Digit -: Not used/defined Data Definition Polling XMT/RCV Selective Comm. Password Comm. 7th Digit -: Not used/defined Data Definition Sub-address Comm. Confidential Comm. Relayed Comm. Turnaround Polling 8th Digit -: Not used/defined Data Definition Advanced Comm.
  • Page 138 Troubleshooting 9th Digit -: Not used/defined Data Definition Short Protocol Standard / Non-Standard Standard Standard Standard Standard Standard Standard Standard Standard Non-Standard Non-Standard Non-Standard Non-Standard Non-Standard Non-Standard Non-Standard Non-Standard 10th Digit -: Not used/defined Data Definition Coding 11th Digit -: Not used/defined Data Definition Symbol Rate (V.34)
  • Page 139 Panasonic UF-585 / 595 12th Digit -: Not used/defined Data Definition Modem Speed Modem Speed (V.34) 2400 bps 4800 bps 2400 bps 7200 bps 4800 bps 9600 bps 7200 bps TC 7200 bps 9600 bps TC 9600 bps 12000 bps...

  • Page 140: Service Modes

    Panasonic UF-585 / 595 5 Service Modes Service Mode Table The following Service Modes are provided to assist you in setting operational functions of the unit and determining the condition of the unit. Service Mode Description Function Parameter Setting Allows changes to the function parameters (the home position, etc...).

  • Page 141: Service Mode 1 (Function Parameter Setting)

    Service Modes Service Mode 1 (Function Parameter Setting) Use the following procedure to change the function parameters. Step Operation or Unit Condition LCD Display Standby MAR-12-1999 15:00 Press “FUNCTION” and then “7”. SET MODE (1-6) ENTER NO. OR Press “MONITOR” four times, then press “*”. SERVICE MODE ENTER NO.
  • Page 142 Panasonic UF-585 / 595 Function Parameter Table Parameter (see Note 3) Selections Function MON/TEL DIAL 1 = Monitor Selects whether the machine starts to TX 2 = TEL/DIAL automatically during On-Hook dialing. (Monitor: Start to TX after pressing START) (TEL/DIAL: Start to TX automatically)
  • Page 143 Service Modes Function Parameter Table Parameter (see Note 3) Selections Function TX START 2400 bps Selects the transmission modem start speed, 4800 bps 14400/12000/TC9600/TC7200/9600/7200/4800/ 7200 bps 2400 bps. 9600 bps TC7200 bps Note: TC9600 bps This parameter is applicable only when communi- 12000 bps cating with regular G3 machines.
  • Page 144 Panasonic UF-585 / 595 Function Parameter Table Parameter (see Note 3) Selections Function PAUSE TIME 1 = 1 sec. Selects the pause interval from 1 sec. ~ 10 sec. for dialing through a switchboard or for international 10 = 10 sec.
  • Page 145 Service Modes Function Parameter Table Parameter (see Note 3) Selections Function LINE ERROR 128 lines 1. Selects the line disconnect condition during 256 lines reception. If the number of line errors exceed this 512 lines setting, the unit will disconnect the line. 1024 lines 2.
  • Page 146 Panasonic UF-585 / 595 Function Parameter Table Parameter (see Note 3) Selections Function COLLATION (PC) 1 = Off Selects the Print Collation mode when activating 2 = On the CFP Protocol. 3 = Auto (Fax Parameter #65 is carried out when “3 = Auto”...

  • Page 147: Service Mode 3 (Printout Of Lists, Reports And Test Results)

    Service Modes Service Mode 3 (Printout of Lists, Reports and Test Results) From this Service Mode you can print the Function Parameter List, Page Memory Test, Printer Report, All Document File, Protocol Trace and the Toner Order Form. 5.3.1 Function Parameter List A list of all Function Parameters can be printed by the following procedure.
  • Page 148 Panasonic UF-585 / 595 Function Parameter List (Sample) *************** -FUNCTION PARAMETER- ************** DATE MAR-12-1999 ***** TIME 12:07 *** P.01 000 MON/TEL DIAL:[Monitor] Monitor 050 RING DET MODE:[Normal] Normal 001 ALARM STATUS:[Timer] Timer 051 ---------- 002 STOP COMM.JRNL:[On] On 052 PULSE RATE:[10pps] 10pps...
  • Page 149 LBP ROM VERSION : 300102 TRANSMIT COUNTER : 000475 RECEIVE COUNTER : 000398 COPY COUNTER : 001083 PRINT COUNTER : 001575 PRINT ERROR 1.MAR-11-1999 15:38 NO.001-12 2.MAR-10-1999 10:48 NO.001-11 3.MAR-09-1999 15:23 NO.004-36 PANASONIC ************************************ - PANAFAX - ***** - 12345678901234567890 - ********...
  • Page 150 Panasonic UF-585 / 595 5.3.3 Page Memory Test A test pattern prints out for cheking the page memory (IC6 on the SCB PCB/ IC6 and 7 on the SCA PCB) and printer mechanism using the following procedure. Step Operation or Unit Condition...
  • Page 151 Service Modes 1. Printer Error Code Table Error Description of Problems Cause Code No problem detected The Timing Sensor turned OFF before a certain period of 1. Recording Paper Jam. time. 2. Timing Sensor defective 3. Incorrect paper size setting. Timing Sensor did not turn ON within a certain period of time.
  • Page 152 Panasonic UF-585 / 595 2. Printer Error Detail Explanation Recording Paper Jam Detection...
  • Page 153 Service Modes Fuser Error Detection...
  • Page 154 Panasonic UF-585 / 595 LSU Error Detection...
  • Page 155 Service Modes Out of Toner Detection Toner Sensor Output Signal Status A (Enough toner in the cartridge) Max. - min. voltage is less than 1.0V Min. voltage is more than 1.4V Status B (Remaining toner is getting low) Max. - min. voltage is less than 0.25V Min.
  • Page 156 Panasonic UF-585 / 595 5.3.4 Print All Document Files Prints all the document files from the Flash Memory. (This function will be available as a running change in the future) Step Operation or Unit Condition LCD Display Standby MAR-12-1999 15:00 Press “FUNCTION”...
  • Page 157 : TSI 2B 20 20 20 38 37 2B 2B 2B 2B 39 38 36 36 35 34 37 38 38 30 DCS 00 C6 F8 44 COMMAND LOG. REMOTE : NSF LOCAL PPS-EOP ------------------------------------------------------------------ REMOTE : MCF LOCAL -PANASONIC- ************************************ -PANAFAX UF-595- ***********-12345678901234567890-******...
  • Page 158 Panasonic UF-585 / 595 5.3.6 Toner Cartridge Order Form The Toner Cartridge Order Form can be printed out manually by the following procedure. Step Operation or Unit Condition LCD Display Standby MAR-12-1999 15:00 Press “FUNCTION” and then “7”. SET MODE (1-6) ENTER NO.
  • Page 159 Service Modes Explanation of Contents (1) Low Toner Message (Fixed) “The toner supply in your facsimile machine is running low” (2) Dealer Name Up to 25 digits Up to 36 digits Toner Order Tel # (4) Toner Order Fax # Up to 36 digits (5) Customer ID Up to 16 characters (User Identification Code)

  • Page 160: Service Mode 4 (Modem Test)

    Panasonic UF-585 / 595 Service Mode 4 (Modem Test) 5.4.1 Binary Signal This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. Step Operation or Unit Condition LCD Display...
  • Page 161 Service Modes 5.4.2 Tonal Signal This Service Mode is used to check the tonal signal output. Signals can be output to the line using the following procedure. Step Operation or Unit Condition LCD Display Standby MAR-12-1999 15:00 Press “FUNCTION” and then “7”. SET MODE (1-6) ENTER NO.
  • Page 162 Panasonic UF-585 / 595 5.4.3 DTMF Signal This Service Mode is used to check the DTMF (Dual Tone Multi Frequency) signal output. The DTMF signal can be generated using the following procedure. Step Operation or Unit Condition LCD Display Standby...
  • Page 163 Service Modes DTMF Single Tone Table Number DTMF Signal Tones 697 Hz 770 Hz 852 Hz 941 Hz 1209 Hz 1336 Hz 1477 Hz 1633 Hz DTMF Dual Tone Table Number DTMF Dual Tones 941 Hz + 1336 Hz 697 Hz + 1209 Hz 697 Hz + 1336 Hz 697 Hz + 1477 Hz 770 Hz + 1209 Hz...
  • Page 164 Panasonic UF-585 / 595 5.4.4 Binary Signal (V.34) (UF-595 only) This Service Mode is used to check the binary V.34 Signals output. Signals can be output to the line using the folowing procedure. Step Operation or Unit Condition LCD Display...

  • Page 165: Service Mode 5 (Diagnostic)

    Service Modes Service Mode 5 (Diagnostic) 5.5.1 CCD Test This Service Mode is used to check the CCD. Use the following procedure to initiate the test. Step Operation or Unit Condition LCD Display Standby MAR-12-1999 15:00 Press “FUNCTION” and then “7”. SET MODE (1-6) ENTER NO.
  • Page 166 Panasonic UF-585 / 595 5.5.2 LCD / LED Test This Service Mode is used to check the LCD and LEDs. Use the following procedure to initiate the test. Step Operation or Unit Condition LCD Display Standby MAR-12-1999 15:00 Press “FUNCTION” and then “7”.

  • Page 167: Service Mode 6 (Ram Initialization)

    Service Modes Service Mode 6 (RAM Initialization) Initializes RAM and restores the Function Parameters to their default values. Note: This operation should be performed when the unit is first installed. Step Operation or Unit Condition LCD Display Standby MAR-12-1999 15:00 Press “FUNCTION”...

  • Page 168: Service Mode 7 (Lbp Service Mode)

    Panasonic UF-585 / 595 Service Mode 7 (LBP Service Mode) This Service Mode is used to change printer parameters and verify printer information. Use the following procedure to change printer parameter. Step Operation or Unit Condition LCD Display Standby MAR-12-1999 15:00 Press “FUNCTION”...

  • Page 169: Service Mode 8 (Check & Call)

    Service Modes Service Mode 8 (Check & Call) 5.8.1 Overview This feature enables the Authorized Servicing Dealers to manage and improve the Fax machine maintenance to their customers by alerting them of equipment problems. It also can be used as a Supply Sales Tool by alerting the Dealer that the unit is running Low on Toner.

  • Page 170: Setting Operation

    Panasonic UF-585 / 595 5.8.3 Setting Operation 8:CHECK & CALL PRESS SET TO SELECT SET or START SET or START CHECK & CALL (1-7) SERVICE ALERT FAX # CLEAR CLEAR 1:SVC. ALERT FAX # SET or START Enter a destination fax number for the Service Alert Report.
  • Page 171 Service Modes Note 1. Service Alert Report To enable the automatic transmission of Service Alert Report, enter the destination fax telephone number in the “SERVICE ALERT FAX #" field. When a printer error occurs, the Service Alert Report is transmitted to the designated number automatically.

  • Page 172: Service Alert Report Format

    Panasonic UF-585 / 595 5.8.4 SERVICE ALERT REPORT FORMAT Explanation of Contents (1) Date & Time when a problem occurred (2) Information Code (3) Printer Error Code Refer to Service Manual (4) Customer ID Up to 16 characters (User Identification Code)

  • Page 173: Maintenance Alert Report Format

    TRANSMIT COUNTER : 999999 (7) RECEIVE COUNTER : 999999 COPY COUNTER : 999999 PRINT COUNTER : 999999 -LOGO PANASONIC ************************************ -CHARACTER ID - ***** -31415926535897932384-*********** Explanation of Contents (1) Low Toner Message (Fixed) “MACHINE IS RUNNING OUT TONER” (4) Customer ID...

  • Page 174: Service Mode 9 (System Maintenance)

    Panasonic UF-585 / 595 Service Mode 9 (System Maintenance) 5.9.1 Overview This Service Mode is used to maintain and/or update the firmware of the machine. Use the following procedure for System Maintenance. Step Operation or Unit Condition LCD Display Standby...
  • Page 175 Service Modes 5.9.2 Operation 9:SYSTEM MAINTENANCE PRESS SET TO SELECT SYSTEM MAINT.(1-8) UF-XXXAAV12300AU FIRMWARE UPDATE 1:FIRMWARE UPDATE PRESS SET TO START * IN PROGRESS * SYSTEM MAINT.(1-8) UF-XXX AAV12300AU FIRMWARE BACKUP 2:FIRMWARE BACKUP PRESS SET TO START * IN PROGRESS * FIRMWARE BACKUP * COMPLETED * SYSTEM MAINT.(1-8)
  • Page 176 (2) Remove the Memory Card Cover. Memory Card Cover (3) Insert the Flash Memory Card gently into the card slot with the Panasonic logo facing to the outside of the machine. Caution: Installing the Flash Memory Card in the wrong direction may damage the connecting pins inside the machine.
  • Page 177 Service Modes 5.9.4 Send Received File This function is the relief mode which makes it possible to retrieve memory received documents during a fatal printer error by transferring the documents to another fax machine. MAR-12-1999 15:00 FUNC MON X 4 SERVICE MODE ENTER NO.

  • Page 178: System Description

    Panasonic UF-585 / 595 6 System Description Mechanical Operation The mechanical units are installed in a single unit body. The mechanical block consists of the following mechanisms: Transmit Mechanism Control Panel Receive Mechanism Printing Process Operation Covers and Enclosures 6.1.1 Transmit Mechanism The Transmit Mechanism consists of components which feed, scan and eject documents, as well as send signals.
  • Page 179 The Separation Rubber (207) separates documents placed on the ADF, preventing multiple feeding. A4 LED Array (329) The UF-585/595 has one LED Array, used as a light source to illuminate the document. The LED Array turns ON when the Read Point Sensor is activated by the document leading edge.
  • Page 180 Panasonic UF-585 / 595 Drive System Eject Roller (303) Feed Roller (302) ADF Roller (331) Document B55D16 Gear (312) ADF Gear (305) D17 Gear (313) D25F Drive Gear (332) Transmit Motor (324) B55D30 Gear (311) D50 Gear (314) B54B22 Gear (310) 6.1.2...

  • Page 181: Receive Mechanism

    These components and their functions are as follows: Paper Feed Units No.1 and 2 UF-585: Paper Feeder Unit No. 2 is not available. UF-595: Paper Feeder Unit No. 2 is available as an option.
  • Page 182 Panasonic UF-585 / 595 Paper Feed Unit No. 2 (Optional) Operation The Paper Feed Unit No.1 always takes priority. The Paper Feed Unit No. 2 becomes operational only when the cassette No.1 runs out of paper and the NP Sensor is deactivated, causing the nPCHK1 output signal level to go High.

  • Page 183: Printing Process Operation

    System Description 6.1.4 Printing Process Operation Charge In the dark, the Bias Charge Roller (BCR) applies a high, uniform negative charge to the surface of the OPC Drum. The surface potential is approximately -650 VDC and remains because the drum has a high electric resistance in the dark. Exposure A portion of the laser beam is deflected to the timing sensor [Beam Detection (BD) Sensor], which controls the start timing of scanning on the OPC Drum.
  • Page 184 Panasonic UF-585 / 595 Transfer and Separation As the paper is fed between the OPC Drum and the Bias Transfer Roller (BTR) (604), a positive charge of approximately +2.5 µA steady current is applied to the backside of the paper by the BTR. The toner particles are attracted away from the drum towards the surface of the paper.
  • Page 185 System Description Beam Detection (BD) Lens and Beam Detection (BD) Sensor The BD Lens receives the reflected light from the Polygon Mirror and redirects it into the BD Sensor, which converts the laser beam into electrical signals and sets the start timing for the scanning line. f-θ...

  • Page 186: Covers And Enclosures

    Panasonic UF-585 / 595 SNS4 PC Board (729) [Paper Exit Sensor] This sensor detects the presence of printed paper at the exit. If no paper passes, or if paper is over the sensor too long, a “RECORDING PAPER JAM” message is displayed. When paper passes over the sensor, the output is Low (Low Active).
  • Page 187 Flash PNL1 PCB WID/ADF SENSOR MEMORY SCA PCB (231) [Actuator A] (224) CARD (422) RP SENSOR F-ROM [Actuator B] (225) SRAM LCD UNIT 1/2/4MB 32KB (233) ADF DOOR SENSOR CCD PCB [ADF Door Actuator] (226) (337) 32768KHz(X) 16MHz(X) TCD1208AP-1 Matrix Image 400dpi F-ROM...
  • Page 188 Flash PNL1 PCB MEMORY WID/ADF SENSOR SCB PCB (231) [Actuator A] (224) CARD (422) RP SENSOR F-RAM [Actuator B] (225) SRAM 1/2/4MB LCD UNIT 32KB (233) ADF DOOR SENSOR CCD PCB [ADF Door Actuator] (226) (337) 32768KHz(X) 16MHz(X) TCD1208AP-1 Matrix Image 400dpi F-ROM...

  • Page 189: Signal Routing

    UF-585: FRIP4 (IC7) Data Bus (16 bit) DRAM F-ROM F-ROM DRAM Line [UF-595: IC6,7,20] Program MODEM (IC5) [UF-595: (IC4 or IC21) [UF-585: IC6] [UF-595: IC10,11] IC6,7,20] Line [UF-585: IC8] [UF-585: IC6] (IC1) Memory Page Image Work Memory Area Memory Buffer PEGASUS SH I/F &...
  • Page 190 Panasonic UF-585 / 595 SRAM Smoothing ROM Laser Printer UF-595: PEGASUS Converter Converter FRIP5 (IC17) (IC2) CCD PCB UF-585: FRIP4 (IC7) Data Bus (16 bit) F-ROM DRAM F-ROM DRAM Line Program [UF-595: IC6,7,20] (IC5) MODEM [UF-595: [UF-585: IC6] (IC4 or IC21)
  • Page 191 UF-585: FRIP4 (IC7) Data Bus (16 bit) DRAM F-ROM F-ROM DRAM Line Program [UF-595: IC6,7,20] MODEM (IC5) [UF-595: (IC4 or IC21) [UF-585: IC6] [UF-595: IC10,11] IC6,7,20] Line [UF-585: IC8] [UF-585: IC6] (IC1) Memory Page Image Work Memory Area Memory Buffer PEGASUS SH I/F &...
  • Page 192 Panasonic UF-585 / 595 SRAM Smoothing ROM Laser Printer UF-595: PEGASUS Converter Converter FRIP5 (IC17) (IC2) CCD PCB UF-585: FRIP4 (IC7) Data Bus (16 bit) DRAM F-ROM F-ROM DRAM Line Program [UF-595: IC6,7,20] MODEM (IC5) [UF-595: (IC4 or IC21) [UF-585: IC6]...
  • Page 193 UF-585: FRIP4 (IC7) Data Bus (16 bit) DRAM F-ROM F-ROM DRAM Line Program [UF-595: IC6,7,20] MODEM (IC5) [UF-595: (IC4 or IC21) [UF-585: IC6] [UF-595: IC10,11] IC6,7,20] Line [UF-585: IC8] [UF-585: IC6] (IC1) Memory Page Image Work Memory Area Memory Buffer PEGASUS SH I/F &...

  • Page 194: Picture Signal Scanning Block

    Xenon Lamp light source. The picture signal from the CCD is amplified in IC19 and input to IC17 (UF-585: IC7), where it is converted from analog to digital and the shading is corrected.
  • Page 195 Offset Control Circuit The Offset Control Circuit consists of Q5, Q4, IC17 and IC19 (UF-585: Q4, Q5, IC7 and IC19), and controls the black level of the CCD output to be at 0V by using the input.

  • Page 196: Ccd Drive Clock Generator Circuit

    CCD. These clock signals are generated by the system clock generator circuit derived from the 4 MHz clock signal that is input to IC9 (UF-585: IC7). Its timing chart is shown below.The FR clock supplied to the CCD is output from the RS of IC2 (PEGASUS).

  • Page 197: Picture Quality Control Circuit

    Circuit Laser Printer I/F Horizontal Sync Circuit Line Data Memory Control Signal Control Signal Control Signal System Register CPU Bus Data Bus Address Timing Address Generator Circuit 16 MHz (IC2) Crystal Oscillator Recording Picture Process Circuit Block Diagram UF-595 (UF-585)

  • Page 198: Line Monitor Circuit

    Panasonic UF-585 / 595 6.2.6 Line Monitor Circuit The Line Monitor Circuit consists of an operational amplifier (IC14, 2), analog switch (IC13), speaker amplifier (Q18, 19) and its peripheral circuits. Its function is to monitor the dial tone, DTMF tone, response signals, etc. over the speaker. It also sounds the output of the key touch tones, alarm tones, etc.

  • Page 199: Transmit Motor Control Circuit

    The transmit motor is a PM type, two-phase bi-polar motor. The stepping signal and chopping current control signals (pTAPH, pTBPH, pTA10, pTA11, pTB10 and pTB11) are sent to the chopper drive circuit, comprised of IC26, IC27 (UF-585: IC9, IC10) and its peripheral circuitry, from IC2 PEGASUS (Panasonic Engine for Graphic Adaptation System Under the SH: DZAC000157) output port.

  • Page 200: Line Control Board

    Panasonic UF-585 / 595 6.2.8 Line Control Board The following shows a block diagram of the Line Control Board. HYBSR Modem Line IC 11 (IC 8) HYSIG Ring Detector IC 1 +24V Telephone IC 1 Off-Hook Detector Port IC17 (IC 7)
  • Page 201 SCA/SCB PC Board controls all dial pulse generation sequences. It turns relay CML and PLS ON and OFF through the MN86075 [IC17] (UF-585: MN86074 [IC7]). The status of the relays during dialing is shown below. When the absence of the terminating message is confirmed by the Off-Hook detector, the CPU turns CML relay ON to develop loop status (DC loop).
  • Page 202 Panasonic UF-585 / 595 6.2.9 SNS PC Board Each sensor consists of an LED and phototransistor. When documents are placed on the ADF tray or are moving, a shutter in the document sensor opens. The light from the LED turns the phototransistor “ON”, and the output voltage from the sensor becomes a “Low”...
  • Page 203 System Description 6.2.10 Control Panel The Control Panel consists of the Display PCB and Panel Unit, which display various status information.It is normally interfaced to the main CPU. Keyed input signals are received by the Panel CPU and the data is transferred to the main CPU on the SCA/SCB PC Board.

  • Page 204: Printer Motor Drive Circuit

    Panasonic UF-585 / 595 6.2.11 Printer Motor Drive Circuit Motor Drive Circuit The Printer Motor is a 4-phase uni-polar PM-type step motor. The step signals (pMMP0A to pMMP3A) are transmitted to IC6 (the Chopper Drive Circuit) by means of a CPU with real-time output function. The chopper current is determined by the voltage at IC6, Pin3 and Pin13.
  • Page 205 System Description Fuser Lamp Drive Circuit The Fuser Lamp is powered by 115 VAC. It is driven by the LVPS and controlled by the nSSR signal from the SCA/SCB PC Board. When the CN33, Pin10 (nSSR) on the LVPS goes LOW, the Fuser Lamp turns ON. This lights up the PC301 LED and activates the CR301 photo-triac, and VAC 115 VAC is sent to the Fuser Lamp.
  • Page 206 Panasonic UF-585 / 595 Fuser Temperature Control Circuit The fuser temperature is controlled by IC1 on the LPC PC Board, which contains A/D (Analog/Digital) converters ANI0 and ANI7. The Fuser Temperature Control Circuit uses A/D converter, ANI0. When thePC301 drive current is transmitted from the LPC PC Board to the LVPS, the Fuser Lamp turns ON.
  • Page 207 System Description High Voltage Drive Circuit (Charging, Development and Transfer) High Voltage is provided through a DC to DC converter, which changes the +24 VDC supply voltage to -650 VDC, and output approximately 0.64 KVAC (Steady current: 220 µA) for the Charging Block. The Developer Circuit converts the +24 VDC to between -300 VDC for the development bias, and outputs 1,500 VAC(p-p) at a frequency of 1.875 kHz to charge the toner.

  • Page 208: Interlock Safety Circuit

    Panasonic UF-585 / 595 6.2.12 Interlock Safety Circuit This safety circuit turns OFF the +24 VDC supply voltages when the Printer Cover is opened. When the Printer Cover is opened, the microswitch(es) on the ILS PC Board are de-actuated, turning OFF +24 VDC to the Printer Drive Circuit, the High Voltage Power Supply, and the Paper Feed Solenoid Circuits, turning OFF the +5 VDC supply voltage for the Laser Driver circuits, on the Laser Unit.
  • Page 209 System Description 6.2.13 Laser Unit (LSU) Control Circuit The laser control signals are described below. nLDON The LSU is activated when this output signal is LOW. If an error occurs, the nLDON output signal level goes High and the LSU is deactivated.
  • Page 210 +5 VP OUTPUT +5 VP OUTPUT CIRCUIT INPUT RECTIFIER CONVERTER +5 VP OUTPUT INPUT +5 VDC CIRCUIT CIRCUIT CIRCUIT OUTPUT (Q101) C105 CIRCUIT A-B Voltage -12 VDC OUTPUT CIRCUIT -12 VDC OUTPUT CONTROL C-D Voltage +24 VDC OUTPUT CIRCUIT +24 VDC OUTPUT CIRCUIT OVER CURRENT...
  • Page 211 System Description ETXDN200A4D (115V) Input Circuit AC line voltage travels to the rectifying circuit through the line filter. The line filter eliminates RFI noise which may otherwise pass to the AC line from the power supply unit. It also protects the power supply unit from transient noise which may pass into the unit from the AC line.
  • Page 212 Panasonic UF-585 / 595 The value of output voltage is Ton : ON time of Q102 Eo=d/(1-d)*Ei Ts : Period of oscillation d=Ton/Ts Equivalent circuit model for the RCC. In the equivalent circuit ; When SW is ON, current D(D203)

  • Page 213: Exploded View & Parts List

    Panasonic UF-585 / 595 7 Exploded View & Parts List Cover Assembly AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location DZKP000166 Spring Plate, Doc. Guide DZMC000525 Cover, Right DZMC000527 Cover, Left (UF-585) DZMC000566 Cover, Left (UF-595)
  • Page 214 to Fig.4 L5_H11/3/19 (OPTIONAL) 2 2 2 to Fig.4 Fig. 1: Cover Assembly...

  • Page 215: Control Panel

    Panasonic UF-585 / 595 Control Panel AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location DZJB000106 Chassis, Control Panel DZJC000216 Holder, Separation Rubber DZKL000023 Lever, ADF Adjustment DZKP000164 Spring, Plate 3J, 3K DZKR000016 Spring, Wire 4G, 6G, 8J...
  • Page 216 L5_H11/3/19 2 2 2 Fig. 2: Control Panel...

  • Page 217: Transmitter Assembly

    Panasonic UF-585 / 595 Transmitter Assembly AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location DZJB000105 Guide, Transmit DZLA000163 Roller, Feed DZLA000164 Roller, Eject DZKG000094 Shaft, Clutch DZLF000270 Gear, ADF DZJA000584 Bracket, LED DZJA000585 Clip, LED...
  • Page 218 L5_H11/3/19 2 2 2 to Fig.4 to Fig.4 to Fig.4 to Fig.4 Fig. 3: Transmitter Assembly...

  • Page 219: Electrical Parts

    Panasonic UF-585 / 595 Electrical Parts AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location DZEC101039 PC Board, LPC DZEC101038 PC Board, LCU DZMC000515 Bracket, AC Inlet DZMC000517 Cover, LVPS Protection DZMC000518 Bracket, Left Printer I/F...
  • Page 220 L5_H11/3/19 (OPTIONAL) 2 2 2 to Fig.7 to Fig.5 to Fig.1 to Fig.1 to Fig.3 to Fig.5 Fig. 4: Electrical Parts to Fig.7 to Fig.9 to Fig.6...

  • Page 221: Base Unit

    Panasonic UF-585 / 595 Base Unit AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location DZJA000587 Chassis, Bottom DZJA000588 Chassis, Right DZJF000356 Chassis, Left Sub DZMC000535 Chassis, Left DZMC000536 Chassis, Rear DZKP000162 Spring Plate, Toner Sensor...
  • Page 222 L5_H11/4/5 to Fig.4 to Fig.6 to Fig.4 to Fig.4 to Fig.6 to Fig.6 to Fig.4 to Fig.4 Fig. 5: Base Unit...

  • Page 223: Paper Transportation

    Panasonic UF-585 / 595 Paper Transportation AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location DZJF000353 Guide, Transfer DZJF000355 Guide, BTR DZHA000114 Sheet, Mylar DZLA000174 Roller, Bias Transfer DZLM000085 Bushing, Left BTR (White) DZKN000025 Spring, BTR...
  • Page 224 L5_H11/3/19 to Fig.5 to Fig.7 2 2 2 to Fig.7 to Fig.5 Fig. 6: Paper Transportation to Fig.5 to Fig.4...

  • Page 225: Fuser Unit

    Panasonic UF-585 / 595 Fuser Unit AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location DZHP002455 Fuser Unit DZJB000112 Frame, Fuser DZJF000354 Guide, Lower Paper Exit DZGT000021 Brush, Discharge DZKK000039 Plate, Pressure Roller Arm 4H, 6J...
  • Page 226 L5_H11/3/19 to Fig.4 to Fig.6 2 2 2 to Fig.4 to Fig.6 Fig. 7: Fuser Unit...

  • Page 227: Cassette

    Panasonic UF-585 / 595 Cassette AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location DZJF000359 Base Frame, Cassette DZJF000360 Guide, Paper Length DZJF000364 Guide, Paper Width DZJF000362 Cover, Cassette DZJF000365 Tray, Document Return DZKM000018 Plate, Pressure...
  • Page 228 L5_H11/3/19 2 2 2 Fig. 8: Cassette...

  • Page 229: Option Cassette

    Panasonic UF-585 / 595 Option Cassette AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location DZJB000119 Frame, Option Cassette Base DZMC000514 Plate, Base Frame DZJA000593 Bracket, Gear DZLA000187 Roller 2, Feed DZLF000282 Gear, D62E18 DZLF000283 Gear, E29...
  • Page 230 L5_H11/3/19 to Fig.4 2 2 2 Fig. 9: Option Cassette...

  • Page 231: Packing And Accessories

    Panasonic UF-585 / 595 7.10 Packing and Accessories AU=U.S.A. AC=Canada Safety Part No. Part Name Mark UF-585 UF-595 UF-585 UF-595 Location 1001 DZRB000398 Carton (UF-585) DZRB000407 Carton (UF-595) 1002 DZRH000288 Assembly, Cushion 2D, 2E, 5C, 6E 1003 DZRK000016 Cassette Sheet...
  • Page 232 Exploded View & Parts List L5_H11/3/19 1002 1002 1009 1008 1007 1003 1006 1002 1002 1005 1001 Fig. 10: Packing and Accessories...

  • Page 233: Installation

    Installation 8 Installation Function Key Any function can be started by first pressing and then enter the function number, or by pressing FUNCTION scroll key repeatedly until the desired function appears on the display. Deferred Communication Set Mode 1 = XMT 1 = User Parameters 2 = Polling Date &...

  • Page 234: Main Unit And Accessories

    Panasonic UF-585 / 595 Main Unit and Accessories Unpack the carton and check that you have all the accessories illustrated. Recording Paper Tray Machine Toner Cartridge Telephone Line Cable Power Cord User’s Guide / Quick Guide Lithium Battery and Holder...

  • Page 235: Installing The Accessories

    Installation Installing the Accessories Installing the Lithium Battery (This battery is used to backup the clock during power failures, see page 149 of the User’s Guide) Install the Battery into the Holder and slide it into the slot on the ADF Door as shown.

  • Page 236: Installing The Toner Cartridge

    Panasonic UF-585 / 595 Installing the Toner Cartridge Unpack the Toner Cartridge and rock it back and forth as shown for 5 or 6 times to even the Toner Cartridge toner inside. Remove the protective seal. Note: Pull on the seal slowly and straight out.
  • Page 237 Installation Align the projections on both sides of the Toner Cartridge with the grooves in the machine as shown and insert the Toner Cartridge into the machine. Note : Lock the Toner Cartridge into place by pressing the handle down and then pushing towards the rear of the machine.

  • Page 238: Loading The Recording Paper

    Panasonic UF-585 / 595 Loading the Recording Paper Paper Specifications In general, most bond papers will produce excellent results. Most photocopy papers will also work very well. There are many "name" and "generic" brands of paper available. We recommend that you test various papers until you obtain the results you are looking for.
  • Page 239 Installation (1) Load the paper into the Paper Cassette. Slide the paper width guide to the left until it Max. Paper lightly touches the stack of paper without Capacity Mark bending the paper. The paper must fit squarely and firmly between the Paper Width Guide and the right side of tray.

  • Page 240: Adjusting The Paper Cassette For The Paper Length

    Panasonic UF-585 / 595 Adjusting the Paper Cassette for the Paper Length How to Adjust the Paper Cassette for the Paper Length The factory default Paper Length setting for the Paper Cassette is on Letter size. To change the paper length to A4 or Legal size, follow the steps below.

  • Page 241: Adjusting The Paper Cassette For The Paper Width

    Installation Adjusting the Paper Cassette for the Paper Width How to Adjust the Paper Cassette for the Paper Width The factory default Paper Width setting for the Paper Cassette is on Letter/Legal size. To change the paper width to A4 size, follow the steps below. (1) Release the left Paper Separation Clip latch.

  • Page 242: Connecting The Telephone Line Cable And Power Cord

    Panasonic UF-585 / 595 Connecting the Telephone Line Cable and Power Cord Power Cord Plug one end of the power cord into an ordinary 3 prong AC outlet and the other end into the receptacle on the rear of the machine.
  • Page 243 Installation External Telephone (Optional) You can connect an additional standard single line telephone to the machine. To connect the telephone, break off the protective tab on the TEL jack.

  • Page 244: Customizing Your Machine

    Panasonic UF-585 / 595 Customizing Your Machine Your facsimile machine has a variety of adjustable Fax Parameters. These parameters, listed in the Parameter Table, are preset for you and do not need to be changed. If you do want to make a change, read the table carefully.

  • Page 245: Fax Parameter Table

    Installation Fax Parameter Table Setting Parameter Setting Comments Number CONTRAST Normal Setting the home position of the CONTRAST key. Lighter Darker RESOLUTION Standard Setting the home position of the RESOLUTION key. Fine S-Fine STAMP Setting the home position of the STAMP key. To select the stamp function when document is stored in memory, see Fax Parameter No.
  • Page 246 Panasonic UF-585 / 595 Setting Parameter Setting Comments Number OPERATOR 20 sec. Selecting the length of time that your machine signals (rings) for an CALL TIMER incoming voice call in Fax/Tel Auto Switching mode. 30 sec. (See page 64 of the User’s Guide) 40 sec.
  • Page 247 (See page 63 of the User’s Guide) Valid DIAGNOSTIC Setting the password for Remote Diagnostic Mode. Please ask (----) PASSWORD your Panasonic Authorized Dealer for details. SUB-ADDRESS Setting a 20-digit password for secured sub-address (----) PASSWORD communication. Continued on the next page.
  • Page 248 Panasonic UF-585 / 595 Setting Parameter Setting Comments Number FAX FORWARD Invalid Selecting whether the machine performs Fax Forwarding to the specified destination . (See page 97 of the User’s Guide) Valid COVER SHEET Setting the home position of the Cover Sheet parameter in the Select Mode.

  • Page 249: Options And Supplies

    Panasonic UF-585 / 595 9 Options and Supplies Options and Supplies Please contact your local Panasonic dealer for availability. 1. Options Order No. Picture Description Available Models UF-585 UE-403117 Handset Kit UF-595 250 Sheet Letter / Legal / A4 Size Paper...

  • Page 250: Installing Optional 250 Sheet Paper Cassette (Ue-409070)

    Options and Supplies Installing Optional 250 Sheet Paper Cassette (UE-409070) 1. Contents Qty. Description Part No. Remarks 250 Sheet Paper Cassette with Feeder Unit UE-409070 2. Installation Note: Install this Feeder Unit as the 2nd Feeder Unit only. (1) Disconnect the Telephone Line Cable and the Power Cord.
  • Page 251 Panasonic UF-585 / 595 (13) Secure the 250 Sheet Paper Cassette with the 4 screws removed in step 10. (14) Place the machine upright. (15) Connect the CST2-CSTSNS2 Harness (927) into the (15) Connector CN66 on the LPC PC Board.

  • Page 252: Installing Handset Kit (Ue-403117)

    Options and Supplies Installing Handset Kit (UE-403117) 1. Contents Qty. Description Part No. Remarks Handset DZDU000031 Handset Cord DZFN000066 Cradle Assembly DZML000132 2. Installation (1) Disconnect the Power Cord and the Telephone Line Cable. (2) Break off the protective tab on the HANDSET Jack on the machine.

  • Page 253: Installing Parallel Port Interface Kit (Ue-404071)

    Panasonic UF-585 / 595 Installing Parallel Port Interface Kit (UE-404071) 1. Contents Qty. Description Part No. Remarks Parallel Port Interface Assembly DZHP002990 Screw DZPB000007 Printer Driver (Floppy Disk 2HD) DZQW000113 1 disk 1 set Scanner Driver (Floppy Disk 2HD) DZQW000114 4 disks 2.

  • Page 254: Schematic Diagram

    10 Schematic Diagram 10.1 SCA PC Board (UF-595)
  • Page 255 Model Drawing Name UF-595 SCA PC Board (2/9)
  • Page 256 Model Drawing Name UF-595 SCA PC Board (3/9)
  • Page 257 Model Drawing Name UF-595 SCA PC Board (4/9)
  • Page 258 Model Drawing Name UF-595 SCA PC Board (5/9)
  • Page 259 Model Drawing Name UF-585 SCB PC Board (6/6)
  • Page 260 Model Drawing Name UF-595 SCA PC Board (7/9)
  • Page 261 Model Drawing Name UF-595 SCA PC Board (8/9)
  • Page 262 Model Drawing Name UF-595 SCA PC Board (9/9)
  • Page 263 Model Drawing Name UF-585 SCB PC Board (1/6)
  • Page 264 Model Drawing Name UF-585 SCB PC Board (2/6)
  • Page 265 Model Drawing Name UF-585 SCB PC Board (3/6)
  • Page 266 Model Drawing Name UF-585 SCB PC Board (4/6)
  • Page 267 Not Mounted Mounted Model Drawing Name UF-585 SCB PC Board (5/6)
  • Page 268 Model Drawing Name UF-585 SCB PC Board (6/6)
  • Page 269 Mounted Model Drawing Name LCU PC Board (1/1) UF-585/595...
  • Page 270 Mounted Mounted Mounted Model Drawing Name UF-585/595 LCE PC Board (1/1)
  • Page 271 Model Drawing Name Power Supply PC Board (100V) UF-585/595 ETXDN200A4D...
  • Page 272 Model Drawing Name Power Supply PC Board (200V) UF-585/595 ETXDN200E4D...
  • Page 273 Model Drawing Name High Voltage Power Supply UF-585/595 PC Board (1/1) EUKMBN731HA...
  • Page 274 Model Drawing Name PANEL PC Board 1 UF-585/595 DZEC101103...
  • Page 275 Model Drawing Name PANEL PC Board 2 UF-585/595 DZEC101103...
  • Page 276 Model Drawing Name PANEL PC Board 3 UF-585/595 DZEC101103...
  • Page 277 Mounted Pad Switch Mounted Model Drawing Name LPC PC Board (1/3) UF-585/595 DZEC101039...
  • Page 278 Mounted Pulse Mounted Motor Mounted HVPS Paper Feed Clutch Model Drawing Name LPC PC Board (2/3) UF-585/595 DZEC101039...

  • Page 279: Option Cassette

    Door Sensor Timing Mounted Feed Sensor Cassette Mounted Sensor Thermistor Mounted No Paper Mounted Sensor Toner Mounted Mounted Mounted Mounted Option Cassette Mounted Mounted Mounted Model Drawing Name LPC PC Board (3/3) UF-585/595 DZEC101039...
  • Page 280 Model Drawing Name SNS PC Board 1 UF-585/595 DZEP000376...
  • Page 281 Model Drawing Name SNS PC Board 2 UF-585/595 DZEC101076...
  • Page 282 Model Drawing Name SNS PC Board 3 UF-585/595 DZEC101163...
  • Page 283 Model Drawing Name SNS PC Board 4 UF-585/595 DZEC101263...
  • Page 284 Model Drawing Name ILS PC Board (1/1) UF-585/595 DZEC100262...
  • Page 285 Model Drawing Name SRU PC Board UF-585/595 DZEC100422...
  • Page 286 Model Drawing Name CST2 PC Board (1/1) UF-585/595 DZEC101076...
  • Page 287 Model Drawing Name PRTA PC Board UF-585/595 DZEC101210...
  • Page 288 Model Drawing Name PRT 1 PC Board UF-585/595 DZEC101464...
  • Page 289 Model Drawing Name PRT 2 PC Board UF-585/595 DZEC101464...
  • Page 290 Model Drawing Name PRT 3 PC Board UF-585/595 DZEC101464...

This manual is also suitable for:

Uf-595

Table of Contents