Page 6
DDX6019/6029/6029Y/6039 COMPONENTS DESCRIPTION Ref. No Application / Function Operation / Condition / Compatibility IC815 Sync separation IC Sync separation Q3,5 Short detection circuit For SW5.0V Q7,8 Short detection circuit For SW8.5V Q60,61 For SW3.3V Q101 Emitter follower Current amplification and buffer for OSD_R signal...
Page 7
DDX6019/6029/6029Y/6039 COMPONENTS DESCRIPTION Ref. No Application / Function Operation / Condition / Compatibility IC101 IC103 video switching signal line IC102 Makes the signal negative IC103 Chroma IC Chroma decoder, correction video signal processing IC IC104 IC103 VMUTE signal line IC106...
Page 8
DDX6019/6029/6029Y/6039 COMPONENTS DESCRIPTION Ref. No Application / Function Operation / Condition / Compatibility IC12 2ch D/A converter Convert audio digital signal to analog signal IC30 DVD processor MPEG decoder function processor (AV decoder) IC40 Power supply IC for A5V IC41...
Page 9
DDX6019/6029/6029Y/6039 MICROCOMPUTER’S TERMINAL DESCRIPTION SYSTEM MICROCOMPUTER: 703266YGJ504A (X34: IC304) Truth Pin No. Pin Name Application Processing Operation Description value table AVREF0 AVSS VMUTE3 MUTE to free-run timing controller H: When FULL OSD, L: When EXCEPT VMUTE2 Switching chroma input SYNC...
Page 10
DDX6019/6029/6029Y/6039 MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Pin No. Pin Name Application Processing Operation Description value table CRM_SDA Chroma IC control (RB5P0090) CRM_SCL Chroma IC control (RB5P0090) 43~47 L fixed DAC_MUTE MUTE control to audio -com H: MUTE OFF, L: MUTE ON...
Page 11
DDX6019/6029/6029Y/6039 MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Pin No. Pin Name Application Processing Operation Description value table DVS_SYS_REQ DVS-7600 communication request output L fixed (LOW) DVS_BE_PON DVS-7600 power supply control H: PON (LOW) DVS_BE_RST DVS-7600 reset BVSS BVDD TILT_M+ Reversed tilt mechanism motor control + CLOSE...
Page 12
DDX6019/6029/6029Y/6039 MICROCOMPUTER’S TERMINAL DESCRIPTION Truth value table q Destination setting e Screen position Destination TYPE2 TYPE1 TYPE0 Monitor source HPOS1 HPOS2 HPOS3 HPOS4 FULL OSD NTSC SECAM NAVI w Screen mode r E2PROM slave address MODE MODE 1 MODE 2...
Page 13
DDX6019/6029/6029Y/6039 MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Pin No. Pin Name Application Processing Operation Description value table TV_SC_CON Start-up request to TV_COM TV_JUDGE TV-BOX new/old detection VOUT_MUTE3 V. OUT MUTE Refer to the truth value table VOUT_SEL1 V. OUT selector (BA7649) Refer to the truth value table VOUT_SEL2 V.
Page 14
DDX6019/6029/6029Y/6039 MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Pin No. Pin Name Application Processing Operation Description value table AUD_MUTEA E-VOL inputSEL_A MUTE L: MUTE ON, H: MUTE OFF AUD_MUTEB E-VOL inputSEL_B MUTE L: MUTE ON, H: MUTE OFF AUD_MUTEC E-VOL inputSEL_C MUTE L: MUTE ON, H: MUTE OFF...
Page 15
DDX6019/6029/6029Y/6039 MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Pin No. Pin Name Application Processing Operation Description value table LX_CLK/LX_CLK LX BUS clock TUN_SDA F/E I2C data input/output terminal Truth value table q Destination setting Model Destination TYPE3 TYPE2 TYPE1 TYPE0 DDX-CH DDX6019 DDX6029/6029Y...
DDX6019/6029/6029Y/6039 TEST MODE TOUCH screen Operation Specifications • After Touch Position Control, save the memory into the How to enter the test mode E2PROM. There are following 2 ways to enter the test mode: • By 3 points input, memory from the system computer to 1.
Page 19
DDX6019/6029/6029Y/6039 TEST MODE Chroma Auto 1 screen • After the auto adjustment for Chroma, save the memory • [Tact] key specification is shown below. into the E2PROM. Function Auto Adjustment items: RGB_Amplitude Bright SRC/Vol Up/Vol Dw/Open (Eject) As usual Ganma1...
Page 20
DDX6019/6029/6029Y/6039 TEST MODE • The default is Center, and switch among Full Down Cen- Audio Full Up by each click. • Default volume is Step 30. • BRT default is MAX. • Bal/Fad setting is changed among Min Center Max by each click.
Page 21
DDX6019/6029/6029Y/6039 TEST MODE • DVD audio/video checking (TDV-540A) For DVD video checking Title Chapter AudioStream1 Level AudioStream1 AudioStream1 Chapter Up/Dw AM/PM noise AudioStream1 Frequency characteristics AudioStream1 Color bar measurement AudioStream1 DISC DW (M/S) For DVD audio checking Title Chapter AudioStream1...
Page 22
DDX6019/6029/6029Y/6039 TEST MODE • Volume setting is changed to the setting values below by • If a jig is connected and the region is written in, the follow- pressing the remote control Tenkey 2 (Preset 2). ing contents should be cleared.
Page 23
DDX6019/6029/6029Y/6039 TEST MODE Test Mode Screen Specifications • If Graphic screen is displayed while in the test mode, the test mode main screen is displayed. Test Mode Main screen Service MECHA Chroma Chroma Source Set Up Audio Information Touch Hposi...
Page 24
DDX6019/6029/6029Y/6039 TEST MODE DVD error information Information screen DVD Mecha/Read/Hot Error: When the error at the left is • Displays Serial No./each -com’s version information/region detected, “DETECT” is displayed. code/each status, etc. DVD Other Error Last: Display the latest (last) error infor- mation (refer to the error code table).
Page 25
DDX6019/6029/6029Y/6039 TEST MODE Error code table Writing screen for after entering the serial No. DVS-7600 error code Code Error description NO ERROR DVD-Video REGION CODE ERROR DVD-Video PARENTAL LEVEL ERROR DVD DESCRAMBLE FAILED READ ERROR Clear Cancel Enter UNKNOWN DISC...
Page 26
DDX6019/6029/6029Y/6039 TEST MODE EEPROM writing-in completion OK/NG screen EEPROM writing-in completion OK/NG screen Return Write OK/NG Hposi OK/NG Return Key specification Key specification Return: Move on to Test Mode Main screen. Return: Move on to Test Mode Main screen. Note: If NG, go into the test mode again and repeat from Note: If NG, go into the test mode again and repeat from the 1st step.
Page 28
DDX6019/6029/6029Y/6039 ADJUSTMENT Free-Run Frequency Adjustment While checking on the frequency counter, adjust with the vol- ume resistance. Ch1: Input signal Adjustment procedure 1) Set CN200 52 pin DDX_MUTE (TP258) to H for timing con- troller IC3 NHD (22 pin) entry to null.
Page 29
DDX6019/6029/6029Y/6039 ADJUSTMENT 5. After R-output adjustment, press Adjustment Item switch Flicker Adjustment key and switch the adjustment item to Phase. While checking the waveform with an oscilloscope, adjust with Monitor B-output and vary the Phase values and adjust so the volume resistance.
Page 30
DDX6019/6029/6029Y/6039 ADJUSTMENT 3-1. Graphic: Horizontal Display Start Position and Using the OSD key, adjust so that the background is not OSD Display Position Adjustment shown on the both sides of the screen. While checking the screen, adjust on the touch panel.
Page 31
DDX6019/6029/6029Y/6039 ADJUSTMENT Touch Panel Adjustment Screen Check Adjust on the touch panel. Check that no obvious horizontal line is shown on the screen. If one or more horizontal line is found, the following adjust- Adjustment procedure ment may not be done properly.
Page 44
DDX6019/6029/6029Y/6039 PC BOARD (COMPONENT SIDE VIEW) (FOIL SIDE VIEW) DAUGHTER UNIT DAUGHTER UNIT X89-2882-71 X89-2882-71 (J86-0023-05) (J86-0023-05) EJECT NAVI MENU VOL UP VOL DOWN X89-2882-71 Ref. No. Address Refer to the schematic diagram for the values of resistors and capacitors.
Page 45
DDX6019/6029/6029Y/6039 INTERCONNECTION DIAGRAM 12 13 14 15 12 13 14 15 16 11 10 9 DC CORD DC CORD (E30-6530-05) (E30-6531-05) K,M,R,X TYPE E TYPE DVD MECHA (E39-0835-05) DVS-7600V DIGITAL (X92-5430-00) (E30-6528-05) LX-BUS J401 J401 CN301 (E30-6508-05) DVD UNIT VIDEO CONTROL UNIT...
Page 46
DDX6019/6029/6029Y/6039 to DC CORD (X14-974x-xx) SW3.3V BUGND TH301 D301 IC301 M GND POWER IC R302 R7 6.8K TAB2 VGNDB 1.8K BUGND PWGND4 R8 6.8K ILL DET R303 D302 ESD GND 100K 7.0V PARK OUT4- MUTE R304 DGND 7.0V OUT4+ 4.3-0.6V 7.0V...
Page 47
DDX6019/6029/6029Y/6039 X34-A/2- X34-B/2- CN703 BUGND REQ M M GND TH301 REQ S B.U. 1000P SW8V DATA S R302 BLGND BUGND MUTE DATA M 1.8K A GND M GND SW3.3V to CN501 to IC201 to IC201 BU5V A BU5V A DGND...
Page 49
TUN8V FE IF+B IFGND • DC voltages are as measured with P251 AGND a high impedance voltmeter. Val- TUN GND ues may vary slightly due to varia- AGND tions between individual instru- DDX6019/6029/6029Y/6039 (1/4) ments or/and units. X34-A/2- CN601 X14-974x-xx (4/4)
Page 50
DDX6019/6029/6029Y/6039 (X34-439x-xx) (A/2) 14.4V 0-14.4V 0-3.3V DC/DC CONT 5V AVR V GND X14- BL GND 33uH 100P BU 5.0V BL GND SW 3.3V BL 14V 220P BU GND BU GND BU GND 22uH 5V AVR SW 14V SW 14V 9 10 D5V-2 SW 8.5V...
Page 53
C315 • DC voltages are as measured with a high imped- BU3.3V-1 ance voltmeter. Values may vary slightly due to variations between individual instruments or/and units. DDX6019/6029/6029Y/6039 (2/4) X34-439x-xx A/2 (4/4)
Page 54
DDX6019/6029/6029Y/6039 to TILT MECHA (X34-439x-xx) (B/2) CN702 CN703 3.3V BU14V BU14V J700 IC704 R716 100 R761 10 TILT TV R MOTOR R720 100 R766 10 TV G DRIVER R717 100 R762 10 TV B L800 R721 100 R767 10 10uH...
Page 55
Values may vary 2.7K C836 slightly due to variations between indi- TP813 1.5V Q802 C870 R818 vidual instruments or/and units. V SW R830 Q806 TP808 R888 R889 VGND DDX6019/6029/6029Y/6039 (3/4) 29 30 38 39 46 47 49 50 X34-439x-xx B/2 (2/2)
Page 65
DDX6019/6029/6029Y/6039 EXPLODED VIEW (DVD MECHANISM) VFC1 (X16-2380) VPU1 1.4x3 N09-6143-05 (X37-) M1.7x2 N09-6144-05 1.7x4.3 N09-6145-05 M1.4x1.6 N09-6156-05 M1.7x1.6 N09-6230-05 WASHER N19-2192-04 M2x6 N09-6133-05 M2x7.3 N09-6134-05 M1.7x3.5 N09-6203-05 1.4x3.5 N09-6221-15 1.7x4.5 N09-6308-05 WASHER N19-2183-14 44 44 Parts with the exploded numbers larger than 700 are not supplied.
Page 66
DDX6019/6029/6029Y/6039 EXPLODED VIEW (UNIT) 2.6x5 N86-2605-48 M3x2.5 N09-6396-05 M2x2.5 N09-6314-05 PANEL SCREW N09-6360-05 M3x7 N09-6398-05 M3x11 N09-6399-05 M2.6x27 N09-6400-05 M2.6x5 N09-6402-05 N09-6403-05 VME1 M3x5 N09-6425-05 N84-3008-43 N09-4461-05 W254 (X14) X14- A/2 X34- A/2 FPC1 X34- B/2 PME1 Parts with the exploded numbers larger than 700 are not supplied.
Page 67
DDX6019/6029/6029Y/6039 EXPLODED VIEW (PANEL / ACCESSORIES) M2x3 N09-6232-05 N09-6401-05 WASHER N19-2317-04 M2x3 N35-2003-48 X35 A/2 LCD1 (X89) FPC2 Depends on the models. Refer to the parts list. Parts with the exploded numbers larger than 700 are not supplied.
Page 68
DDX6019/6029/6029Y/6039 EXPLODED VIEW (PANEL MECHANISM) M2x2.5 N09-6361-05 M1.7x3.7 N09-6363-05 M2x2.5 N09-6375-05 M2x3.5 N09-6376-05 M2x2.5 N09-6377-05 N09-6378-05 M2.6x4 N09-6379-05 WASHER N19-2321-04 Parts with the exploded numbers larger than 700 are not supplied.
K,R,X,M ............40dB (1kHz) Weight ............. 2.6kg / 5.7 lbs E ..............35dB (1kHz) KENWOOD follows a policy of continuous advancements DANGER: in development. For this reason specifications may be Please do not look the laser beam directly during re- changed without notice.