Advertisement
Available languages
Available languages
DEH-P790BT
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Thailand
Imprimé en Thaïlande
<CRD4209-A/N> UC
<KMINX> <06L00000>
Installation
Note:
DIN Front/Rear-mount
•
Check all connections and systems before final
This unit can be properly installed either from
installation.
"Front" (conventional DIN Front-mount) or
•
Do not use unauthorized parts. The use of
"Rear" (DIN Rear-mount installation, utilizing
unauthorized parts may cause malfunctions.
threaded screw holes at the sides of unit chassis).
•
Consult with your dealer if installation requires
For details, refer to the following installation
drilling of holes or other modifications of the
methods.
vehicle.
•
Do not install this unit where:
— it may interfere with operation of the vehicle.
DIN Front-mount
— it may cause injury to a passenger as a result
of a sudden stop.
Installation with the rubber bush
•
The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
Mounting sleeve
such as near the heater outlet.
Dashboard
•
Optimum performance is obtained when the unit
1 1 1 82
182
is installed at an angle of less than 60°.
Rubber bush
53
53
60°
Screw
•
When installing, to ensure proper heat dispersal
1. Insert the mounting sleeve into the dashboard.
when using this unit, make sure you leave ample
•
When installing in a shallow space, use a sup-
space behind the rear panel and wrap any loose
plied mounting sleeve. If there is enough
cables so they are not blocking the vents.
space behind the unit, use factory supplied
mounting sleeve.
Leave ample space
Dashboard
2. Secure the mounting sleeve by using a screwdriv-
er to bend the metal tabs (90°) into place.
10 cm (3-7/8 in.)
3. Install the unit as illustrated.
10 cm (3-7/8 in.)
Removing the Unit
2. Determine the appropriate position where the
holes on the bracket and the side of the unit
1. Extend top and bottom of the trim ring outwards
match.
to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)
•
It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
3. Tighten two screws on each side.
Use either truss screws (5 mm × 8 mm) or
•
flush surface screws (5 mm × 9 mm), depend-
ing on the shape of screw holes in the
bracket.
2. Insert the supplied extraction keys into both sides
of the unit until they click into place.
3. Pull the unit out of the dashboard.
Dashboard or Console
Factory radio mounting bracket
Fastening the front panel
If you do not plan to detach the front panel, the
front panel can be fastened with supplied screw.
DIN Rear-mount
1. Extend top and bottom of the trim ring outwards
to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)
•
It becomes easy to remove the trim ring if the
front panel is released.
Screw
Trim ring
Installing the microphone
2. Install the microphone clip on the
sun visor.
With the sun visor up, install the micro-
Installation notes
phone clip. (Lowering the sun visor
Install the microphone in a position and ori-
reduces the recognition rate for voice
entation that will enable it to pick up the
operations.)
voice of the person operating the system.
CAUTION
It is extremely dangerous to allow the
microphone lead to become wound around
the steering column or gearstick. Be sure
to install the unit in such a way that it will
not obstruct driving.
Screw
When installing the microphone on
the sun visor
Clamps
Use clamps to secure
1. Install the microphone on the micro-
the lead where neces-
phone clip.
sary inside the vehi-
cle.
Microphone
When installing the microphone on
the steering column
Microphone
clip
1. Install the microphone on the
microphone clip.
Microphone
Microphone
clip
ENGLISH
Microphone clip
Fit the micro-
phone lead into
the groove.
Advertisement
Related Manuals for Pioneer DEH-P790BT
Summary of Contents for Pioneer DEH-P790BT
- Page 1 Installation ENGLISH Note: DIN Front/Rear-mount Removing the Unit 2. Determine the appropriate position where the Installing the microphone 2. Install the microphone clip on the holes on the bracket and the side of the unit • Check all connections and systems before final sun visor.
-
Page 2: Installation
Installation ENGLISH Connecting the Units ENGLISH 2. Install the microphone clip on the Adjusting the microphone angle Note: • Control signal is output through blue/white cable when this unit is powered on. Connect it to an • When this unit is installed in a vehicle without steering column. - Page 3 Connecting the Units ENGLISH 7 When not connecting a rear speaker lead to a Subwoofer 7 When using a Subwoofer without using the optional amplifier 23 cm (9 in.) 23 cm (9 in.) Subwoofer output Subwoofer output 15 cm (5-7/8 in.) 15 cm (5-7/8 in.) (SUBWOOFER OUTPUT) (SUBWOOFER OUTPUT)
- Page 4 Installation FRANÇAIS Installation du microphone 2. Fixez l’attache du microphone sur le 2. Fixez l’attache du microphone Ajustement de l’angle du microphone Remarque: Montage avant/arrière DIN Retrait de l’appareil 2. Déterminez la position appropriée dans laquelle les trous du support de montage coïncident avec •...
- Page 5 Connexions des appareils FRANÇAIS Remarque: — N’attachez jamais ensemble plusieurs câbles négatifs de plusieurs enceintes. • Si cet appareil est installé dans un véhicule sans position ACC (accessoire) sur le commutateur • Le signal de commande est sorti par le câble d’allumage, le câble rouge doit être connecté...
- Page 6 Connexions des appareils FRANÇAIS 7 Quand aucun câble d’enceinte arrière n’est connecté au caisson de grave 7 Lors de l’utilisation d’un caisson de grave sans utiliser l’amplificateur en option 23 cm 23 cm Sortie du caisson de grave Sortie du caisson de grave 15 cm 15 cm (SUBWOOFER OUTPUT)