Panasonic HG-T1010 Instruction Manual
Transmission-type digital displacement sensor / sensor head
Hide thumbs
Also See for HG-T1010:
- Instruction manual (2 pages) ,
- User manual (236 pages) ,
- Instruction manual (2 pages)
Advertisement
Quick Links
HG-T1010
Thank you very much for purchasing Panasonic products. Read this Instruction Man-
ual carefully and thoroughly for the correct and optimum use of this product. Kindly
keep this manual in a convenient place for quick reference.
Never use this product as a device for personnel protection.
When using devices for personnel protection, use products that meet the laws
and standards for personnel protection that apply in each region or country, such
This product inspects (judges / measures) objects. Do not use it to ensure safety,
Avoid observing beams in a dark surrounding environment.
Do not look at beams using an optical device such as an optical telephoto system.
Never attempt to disassemble, repair, or modify this product.
Control or adjustment according to procedures other than those provided in this Instal-
This document provides a brief summary of mounting and other related information.
For detailed information, refer to the
(
"
"
).
1
This product conforms to the regulations and standards below.
2
Instruction Manual (English / Japanese, Chinese / Korean)
General Information for Safety, Compliance, and Instructions
3
In order to prevent user injury caused by a laser product, the following standards
have been established in the IEC Standards, EN Standards, JIS Standards, GB
Standards, KS Standards and FDA Regulations.
ty preventive measures to be implemented for each class.
This product is equivalent to a "
Class 1
A laser that is safe when operated under operating conditions that can be reasonably foreseen.
dards for laser products.
FDA
regulations of the laser standards of the FDA (Food and Drug Administration). In
order to prevent user injury caused by a laser product, Part 1040 (Performance
Standards for Light-Emitting Products) of the FDA standards has been estab-
ify safety preventive measures to be implemented for each class.
This product complies with the FDA regulations (FDA 21 CFR 1040.10 and
)
4
2
3
1
7
7
Name
1 Laser emission indicator (Green)
Lights while laser light is emitted.
2 Light-emitting face
Face that emits the laser.
3 Light-receiving face
Face that receives the laser.
• Lights green: Beam is aligned. (Note 1)
Beam alignment indicator / TOP
4
• OFF: Laser light is not received. (Note 1)
(Orange / Green)
• Blinks green: Beam is aligned, but the light received is faint. (Note 2)
• Lights orange: Beam is aligned, but light received is intense due to
Beam alignment indicator / BOTTOM
stray light or otherwise. (Note 2)
5
(Orange / Green)
• Blinks orange: Beam is aligned, but partially blocked due to an obsta-
cle or otherwise. (Note 2)
• Lights green: Controller judgment output is within the set range.
Judgment output indicator
6
• Lights orange: Controller judgment output is outside the set range.
(Orange / Green)
• OFF: Beam alignment function is in use.
7 Sensor head connection cable connector Connects to the sensor head connection cable.
Notes: 1) For details on beam alignment, refer to "
6
2) For detailed information on beam states, refer to the
.
5
Do not allow contaminants that will refract light such as water, oil or finger-
1 pc. each
prints, or contaminants that will block light such as dust or dirt, to collect on the
1 pc.
light-emitting and light-receiving faces of the sensor head If there is dirt or other
contamination on a surface, wipe with lens paper or a soft cloth that will not leave
that has been moistened with absolute alcohol.
A serial number is indicated on the reverse sides of the light-emitting and light-re-
ceiving faces of the product. Always combine an emitter and receiver with identi-
cal serial numbers.
8mm
-
(Please obtain separately)
Serial number
-
tional)
CN-HT-C
product to the controller.
the controller power before inserting or removing the connectors.
Do not grasp the cable to pull out or insert the connectors. Wires may break if
nector may fall out and cause an error.
The sensor head connection cable branches into two cables. The cables are
identical and can be connected to either the emitter or receiver
1. Insert the sensor head connecting cable to the sensor head connection cable con-
nector of the sensor head with the mark aligned.
-
Mark
Mark
1
1
Sensor head connection cable
CN-HT-C
Sensor head connection cable connector
2. Turn the fastening ring on each sensor head connection cable connector in the
2
2
Fastening ring
1. Turn the fastening ring on each sensor head connection cable connector in the
direction of the arrow to loosen.
4
5
6
2. Grasp each connector on the sensor head connection cable and pull out to remove.
Function
When disconnecting, always make sure that the fastening ring has been complete-
ly loosened before pulling out the cable. Risk of damage if you pull the cable with
6
When installing the product, always register a reference waveform. If a reference
waveform is not registered, correct measurement will not be possible.
Register the reference waveform without a measurement object.
prevent correct detection. In this event, mount the emitter and receiver pair at an
.
justing the angle, always perform beam alignment.
Check the beam alignment indicator (orange / green) on the receiver as you align the beam.
You can also check the state of the emitter / receiver beam on the digital display
of the controller.
1. Move the receiver to align the beam while checking the beam alignment indicator
(orange / green) on the receiver.
If the laser is not incident on the receiver, the beam alignment indicator will not light.
2. If the beam is skewed toward the TOP, only the TOP beam alignment indicator
(green) will light.
If the beam is skewed toward the BOTTOM, only the BOTTOM beam alignment
indicator (green) will light.
TOP: Lights green
BOTTOM: Green OFF
24mm
24mm
The mounting holes in the emitter and
receiver are bilaterally symmetric.
3. When the emitter / receiver beam is correctly aligned, both the TOP and BOTTOM
CN-HT-C
-
beam alignment indicators (green) will light.
-
You can perform reference waveform registration by pressing the ENTER key on
the controller with the beam correctly aligned. The reference waveform is stored
in EEPROM in the receiver.
Note: For detailed information on beam alignment and waveform registration, refer to the
7
The HG-T
and product malfunctioning or damage may occur.
This product has been developed / manufactured for industrial use only.
The receiver in this product uses an EEPROM. The EEPROM has a service life of one mil-
lion setting operations.
product damage. There is also a risk of a noticeable reduction of service life.
To ensure performance, do not use the product after turning ON the power until it has
Do not wire in parallel with a high-voltage line or power line, or run through the same con-
duit. Risk of malfunctioning due to induction.
Do not touch or allow any foreign objects to enter the terminal inside the connector.
Do not allow ambient light such as sunlight to directly enter the sensor head receiver. When
precision is particularly required, take measures such as attaching a shield to the sensor
head.
Avoid use in a location subject to sudden temperature changes that cause condensation.
This product is suitable for indoor use only.
Avoid dust, dirt, and steam.
Do not use in a location where there are corrosive or other harmful gases.
Ensure that the product does not come into contact with organic solvents such as thinner.
1
Ensure that the product does not come into contact with strong acid or alkaline.
Ensure that the product does not come into contact with oil or grease.
1
Do not use the product in a location subject to intense vibration or shock.
The connectors are not structurally dustproof, waterproof, or corrosion-resistant. Do not
use the product underwater or in the rain. Take care of the usage environment.
2
This product is a precision device. Do not drop or otherwise subject to shock. Risk of prod-
2
uct damage.
2
When the product becomes unusable or unneeded, dispose of the product appropriately as
2
industrial waste.
8
SPECIFICATIONS
Type
Model No.
Combined controller
Position detection method
Installation distance
Measurement width
Light source
Repeatability (Note 2)
-
Minimum sensing object (Note 4)
Temperature characteristic
(Note 5)
Protection
Pollution degree
Ambient temperature
Ambient humidity
Ambient illuminance
Operating altitude
Grounding method
Material
Cable
Weight
Beam alignment indicator / TOP
•
Beam alignment indicator / BOTTOM
•
• Measurement object : Opaque knife edge
• Measurement object position condition: Light half-blocked at the center of 100-mm installation distance
Notes: 1) This product complies with the FDA regulations (FDA 21 CFR 1040.10 and 1040.11) in accordance with FDA
2) P-P value of deviations in digital measurements obtained with light half-blocked at the center of installation distance
4) When light is light blocked at the center of 500-mm installation distance.
5) When light is light half-blocked at the center of 100-mm installation distance.
spheric pressure at 0m.
9
TOP: Green OFF
BOTTOM: Lights green
When attaching the Side View Attachment to the emitter, make sure that beam
alignment can be performed.
After mounting the Side View Attachment to the sensor head, check whether the
the reference waveform and conduct operation check.
By attaching the Side View Attachment
can change the laser light emission direction.
To attach the
washer, length: 4 mm). Tighten the screw with a torque of 0.088 N·m or less.
TOP: Lights green
BOTTOM: Lights green
-
.
Notes: 1)
Model No.
HG-TC
Combined sensor head
Installation distance
Linearity (Note2)
Material
Accessory
Weight
Notes: 1) Cannot be attached to the sensor head HG-T1110 (measurement width:10mm / slim type).
Notes: 2) Measured at an installation distance of 100mm.
Panasonic Industry Co., Ltd.
1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8506, Japan
https://industry.panasonic.com/
Please visit our website for inquiries and about our sales network.
Panasonic Industry Co., Ltd. 2024
April, 2024
Measurement width:10mm / standard type
HG-T1010
CMOS method
0mm to 500mm
10mm
Red semiconductor laser Class 1 [IEC / EN / JIS / GB /KS Standards / FDA Regulations (Note 1)]
1μm (at an installation distance of 20mm)
2.5μm (at an installation distance of 100mm)
5μm (at an installation distance of 500mm)
±0.12% F.S. (at an installation distance of 20mm)
±0.28% F.S. (at an installation distance of 100mm)
ø0.5mm (at an installation distance of 500mm)
2
Capacitor grounding
Case: Aluminum die-casting, Light emitting / receiving faces: Glass
Attached 0.2m shielded cable with 4-conductor type, round connector
controller.They
(
).
-
(optional) to the product, you
to the product, use the included setscrew (M2 screw with
Sensor head
installation on both unit
(Optional)
(Optional)
Side View Attachment
(Optional)
M2 screws with washers
(length 4mm)
Emitter
(Included with
)
Receiver
is sold individually. Two
units are required when installing to both emitter and receiver.
(Note 1)
0mm to 100mm (typical)
Main unit: LCP, optical surface: glass
Set screw (M2 screw with washer, length: 4 mm): 2 pcs.
PRINTED IN JAPAN
Advertisement
Related Manuals for Panasonic HG-T1010
Summary of Contents for Panasonic HG-T1010
- Page 1 HG-T1010 Ensure that the product does not come into contact with oil or grease. Thank you very much for purchasing Panasonic products. Read this Instruction Man- Do not use the product in a location subject to intense vibration or shock.
- Page 2 HG-TSV10 https://industry.panasonic.com/ PART1040 Performance Standards for Light-Emitting Products HG-TSV10 HG-T1010 HG-T HG-TC 0mm 100mm Laser Notice No.56 IEC 60825-1 Ed. 3 ±56μm FDA 21 CFR 1040. 10 1040.11 CN-HT-C EEPROM EEPROM HG-T1110 10mm / 100mm Panasonic Industry Co., Ltd. 2024...