Page 2
MODEL COLOR COMMANDER DEST. MODEL COLOR COMMANDER DEST. KD-55X9300C Black RMF-TX100E Hong Kong, India RMT-TX100P KD-55X9300C Black RMF-TX100T Taiwan RMT-TX100T KD-65X9300C Black RMF-TX100E Hong Kong, India, RMT-TX100P SSEA ( Singapore etc ), Thailand, Vietnam. KD-65X9300C KD-65X9300C Black Black RMF-TX100T RMF-TX100T...
Page 3
Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual.
Page 4
Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d’une importance critique pour la securite du fonctionnement Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony Les reglages fonctionnement.
WARNINGS AND CAUTIONS When repairing the LCD panel, be sure you are grounded by using a wrist band. When repairing the LCD panel on the When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover. all the LCD panel m st be sec red sing the 4 mo nting holes on the rear co er Do not press on the panel or frame edge to avoid the risk of electric shock.
Page 6
After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges. 2.
The units in this manual contain a self-diagnostic function. If an error occurs, the Smart Core Red LED will automatically begin to flash. The number of times the LED flashes translates to a probable source of the problem. A definition of the Smart Core Red LED flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
SELF DIAGNOSIS FUNCTION [SELF DIAGNOSTIC SCREEN DISPLAY] Error count Error item Naming Format of error timestamps SELF CHECK YYMMDDhhmmss (in UTC) Example: Example: Back << 120823132523 -> Aug 23 2012 13:25:23 UTC 002 MAIN_POWER 000000000000 000000000000 000000000000 000 * Only when time is set, an error timestamp is saved.
SELF DIAGNOSIS FUNCTION SELF-DIAGNOSTIC SCREEN DISPLAY For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurrences of failure for confirmation on the screen: [To Bring Up Screen Test] In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below: Since the diagnostic results displayed on the screen are not automatically cleared always check the self diagnostic screen...
Page 11
• There are clutch in the yellow frame[ ]. Therefore please be careful in the case of the disassembly or assembly of parts. 1-1-1. STAND L (L) A/STAND R (L) A STAND L (L) A (P/N: 4-562-462-01) STAND L (L) A (P/N: 4 562 462 01) /STAND R (L) A (P/N: 4-562-463-01) R/L side each 2 screws (SCREW, +PSW M5X16) P/N: 2-580-608-01...
Page 13
DISASSEMBLY 1-1-3. LABEL, CI (not applicable for this model) AND LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (W) LABEL, CI LABEL, REAR TERMINAL LABEL, SIDE TERMINAL (W)
Page 14
DISASSEMBLY 1-1-4. AC COVER AND POWER SUPPLY CORD Screw (SCREW, +PSW M4X10) P/N: 4-159-298-01 POWER SUPPLY CORD POWER SUPPLY CORD AC COVER...
Page 44
DISASSEMBLY 1-1-33. GASKET (BMF) GASKET (BMF) GASKET (BMF) NOTE: When you replace a BMFL board, it is necessary to stick five new GASKET on a new BMFL board. stick five new GASKET on a new BMFL board GASKET (BMF): 4-566-117-01 However, there are sets that mount the surface mount type gasket.
Page 54
DISASSEMBLY 1-2-1. STAND L (2L) A/STAND R (2L) A STAND L (2L) A (P/N: 4-562-464-01) /STAND R (2L) A (P/N: 4-562-465-01) R/L side each 2 screws (SCREW, +PSW M5X16) P/N: 2-580-608-01...
Page 56
DISASSEMBLY 1-2-3. LABEL, UNDER TERMINAL AND LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (L) AND LABEL, CI (not applicable for this model) LABEL, CI LABEL, REAR TERMINAL LABEL, UNDER TERMINAL LABEL, SIDE TERMINAL (L)
Page 57
DISASSEMBLY 1-2-4. AC COVER AND POWER SUPPLY CORD Screw (SCREW +PSW M4X10) P/N: 4-159-298-01 POWER SUPPLY CORD AC COVER...
Page 88
DISASSEMBLY 1-2-34. GASKET (BMF) GASKET (BMF) GASKET (BMF) NOTE: When you replace a BMFL board, it is necessary to stick five new GASKET on a new BMFL board. stick five new GASKET on a new BMFL board GASKET (BMF): 4-566-117-01 However, there are sets that mount the surface mount type gasket.
Page 98
DISASSEMBLY 1-3-1. STAND L (3L) A/STAND R (3L) A STAND L (3L) A (P/N: 4-562-466-01 ) /STAND R (3L) A (P/N: 4-562-467-01) R/L side each 2 screws (SCREW, +PSW M5X16) P/N: 2-580-608-01...