hit counter script

Advertisement

AUTOMATION
11 9BS04EN
FOR SLIDING GATES
INSTALLATION MANUAL
BK 800 - 1200 - 1800 - 2200
BKE 1200 - 1800 - 2200
EN
English
www.metalines.com
sales@metalines.com

Advertisement

Table of Contents
loading

Summary of Contents for CAME BK 800

  • Page 1 AUTOMATION 11 9BS04EN FOR SLIDING GATES INSTALLATION MANUAL BK 800 - 1200 - 1800 - 2200 BKE 1200 - 1800 - 2200 English www.metalines.com sales@metalines.com...
  • Page 2: Read Carefully

    Warning Sings (e.g. gate plate). (i.e. that for which it was expressly built for). Any other use is Special instructions and to be considered dangerous. Came Cancelli Automatici S.p.A. advice for users is not liable for any damage resulting from improper, wrongful •...
  • Page 3 www.metalines.com sales@metalines.com...
  • Page 4: Limits Of Use

    009 CCT - Simple 1/2” chain; 009 CGIU - 1/2” chain joint. Important! Check that the safety equipment and accessories are CAME originals; this is a guarantee that also makes the system easy to set up and upkeep. Technical information...
  • Page 5: Parts Description

    Parts description GEARMOTOR UNIT 1 - Gearmotor 2 - Board cover support 3 - End-stop flaps 4 - ZBK-ZBKE basic control board 5 - Electric board front cover 6 - Release door 7 - Base plate 8 - Securing screws 9 - Plates for securing screws 10 - Nuts ACCESSORIES...
  • Page 6: Installation

    Installation Only expert, qualified personnel must carry out the installation, in full compliance with the applicable law. Preliminary checks Before actually installing the gate operator, your are required to: • Check that the leaf is rigid and compact and that the rollers are in good working order and properly greased; •...
  • Page 7 BK or BKE unit Key-operated selector switch Control board incorporated Flashing light indicating door movement Radio receiver Antenna Limit-switch tabs (only for the BK unit) Safety photocells Rack 10 Photocell column 11 Closure stop Motor to base anchorage The following applications are only examples, as the space required for unit installation and the accessories vary depending on dimensions and therefore it is up to the installer to select the best solution.
  • Page 8: Unit Installation

    Unit installation During the initial phase of installation, the feet should protrude by 5-10 mm. in order to allow for alignment, anchorage of the rack and further adjustments. Perfect alignment with the guide rail is made possible by the (paten-ted) built-in regulation system, which consists of: - slots for horizontal adjustment;...
  • Page 9 Attaching the switch tabs (BK series) Position the limit-switch tabs (whose positions determine the limits of gate travel) on the rack. Note: do not allow the gate to strike the mechanical stops in the open or closed positions. Manual release of the gearmotor To open the access door, insert the key A, push down and rotate clockwise.
  • Page 10: Control Board

    Control board Technical description The control board is powered with (120V a.c. or 230V a.c.) across - when closing, inverts the direction of movement of the gate until it is terminals L and N and is protected by fuse on the main power line fully opened and consequently, automatically closes it.
  • Page 11: Electrical Connections

    Electrical connections Connection for gear motor, limit switch or encoder ZBKE ZBKE (Condenser) Connection for the limit switch unit (BK series) Output for 230V (a.c.) motor Connection for connection encoder (BKE series) Modifications to the connection if installing the gear motor on the right side - Invert the phases of the gear motor (U;...
  • Page 12 Connections to the systems Stop button (N.C. contact) - Gate leaf stop- button with exclusion of automatic closing phase, resume motion by pressing the push button or remote control. Key selector and/or opening button (N.0. contact) - Opens the gate leaf. Key selector and/or partial opening button (N.0.
  • Page 13 Connections to safety devices (DIR photocell) Set power supply to 24V a.c./d.c. (N.C.) contact for «re-opening during closing» - Input for safety devices such as photocells, sensitive safety edges and other devices compliant with EN 12978 standards. When the gate leaf is closing, opening the contact triggers the inversion of the direction of movement until the gate leaf is fully open.
  • Page 14 Electrical connection for the check of the operating state of the photocells Each time an open or close command is given, the circuit board checks the effi ciency of the safety devices (i.e. photocells). The fl ashing led indicator on the control panel indicates an anomaly of the photocells (Ref. to point 9, p.
  • Page 15 Selecting functions (dip-switch) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 ON - Automatic Closing - the automatic closing timer is automatically triggered at the end of the opening phase. The adjustable set time of operation, is in any case subordinate to the operation of any safety accessories and is excluded after a total “stop”...
  • Page 16 Programming of limit switches for ZBKE board 1) Close the engage door-panel and insert DIP switch 15 to the ON position, the led indicator of the radio code starts fl ashing. 2) Manually close the gate leaf, press the “CLOSE” button, the led indicator keeps fl...
  • Page 17 Connection of two coupled gear motors with single control 1) Coordinate the direction of gear motors “A” and “B”, by changing the rotation of motor “B” (see connection for the gear motor and limit switches, p. 9). 2) Establish which motor, “A” or “B” will be the master (or pilot), set dip switch 14 to the ON on position on the control board.
  • Page 18 Installation procedure of the transmitter for remote control Input for the remote control’s antenna - Possible second channel For opening and closing of the gate leaf output from the radio recei- using the remote control. Connect the ver (contact N.O.) Contact RG58 cable to the terminal of the antenna output: 5A-24V (d.c.).
  • Page 19 Transmitters ATOMO AT01 • AT02 AT04 see instructions on package TOUCH TOP-432NA • TOP-434NA TCH 4024 • TCH 4048 TOP-862NA • TOP-864NA TOP-432S TOP-432A • TOP-434A TOP-302A • TOP-304A TWIN T132 • T134 • T138 TWIN2 • TWIN4 T152 • T154 • T158 T432 •...
  • Page 20 Memorizing the code on the command board CH1 = Channel for direct commands to a function of the ratiomotor control unit (“open only” / “open-close-invert direction” commands or the “open-stop-close-stop” command, depending on dip-switch 2 - 3 settings). 1) Keep the “CH1” key pressed on the base card (ref.
  • Page 21: Maintenance

    UNI EN ISO 14001 standard to ensure environmental protection. Please continue our eff orts to protect the environment—which CAME considers one of the cardinal elements in the development of its operational and market strategies—simply by observing brief recommendations as regards disposal: DISPOSAL OF PACKAGING –...
  • Page 22 HR • Za sve dodatne informacije o poduzeću, proizvodima i tehničkoj podršci: UK • Для отримання будь-якої іншої інформації про компанію, продукцію та технічну підтримку: www. came.com www. came.com CAME Cancelli Automatici S.p.a. CAME Cancelli Automatici S.p.a. Via Martiri Della Libertà, 15 31030 Dosson Di Casier...

This manual is also suitable for:

Bk 1200Bk 1800Bk 2200Bke 1200Bke 1800Bke 2200

Table of Contents