CAME BY-3500T KIT Quick Setup Manual
Complete kit for a sliding gate weighing up to 3500kg / max. width 23m
Hide thumbs
Also See for BY-3500T KIT:
- Installation manual (97 pages) ,
- Manual (17 pages) ,
- Quick setup manual (12 pages)
Related Manuals for CAME BY-3500T KIT
Summary of Contents for CAME BY-3500T KIT
- Page 1 CAME.COM/UK BY-3500T Complete kit for a sliding gate weighing up to 3500kg / max. width 23m QUICK SETUP GUIDE TO BE READ IN CONJUNCTION WITH THE FULL INSTRUCTION MANUAL...
- Page 2 CONTENTS Control Panel: Kit Contents Quick Start Guide Safety Instructions Control Panel: Programming Transmitters Typical Gate Setup Control Panel: Safety Geometry Optional Accessories Manual Release Instructions Kit Wiring Diagram BY-3500T: KIT CONTENTS topd4Fks top-a433n BY-3500T AF43S Fixed code Transmitter Tuned Antenna Motor with built-in ZT6 Radio Frequency Card control panel...
- Page 3 SAFETY INSTRUCTIONS When correctly installed in compliance to installation instructions and adhering to all current electrical, mechanical and manufacturer regulations, your automation system will provide a high degree of safety and problem free operation. Please take note of the following warnings that must be followed in order to prevent accidents during your gate operation: •...
- Page 4 BY-3500T: TYPICAL GATE SETUP OUTSIDE OF GATES INSIDE OF GATES 1 BY-3500T Motor Selector Keypad (optional) Photocell column (optional accessory) 2 Limit switch fins Photocells (on outside of gate posts) Slide guides 3 Reception Antenna 2nd set of Photocells (optional) Rack 4 Flashing Light (optional) Mechanical End Stop (not supplied)
- Page 5 BY-3500T: GEOMETRY Preliminary checks Tick 1. Ensure that all surfaces are perfectly level (Do not install on slopes) 2. Foundation frame dug out 3. Set up the corrugated tubes needed for the wiring coming out of the junction pit. 4. Use Ø 40 mm corrugated tubes to connect the gearmotor to the accessories 5.
- Page 6 BY-3500T: MANUAL RELEASE The BY-3500T sliding gate operator has a manual release system inside the metal casing. To manually release the gates: 1. Unlock and remove the cover 2. Insert the locking key provided and turn to release the gate. 3.
- Page 7 BY-3500T: wiring diagram Mains Supply 400V 3 Phase Control Panel Cable/length 1m - 10m = H05RN-F 4G x 1.5mm 10m - 20m = H05RN-F 4G x 2.5mm 20m - 30m = H05RN-F 4G x 4mm AF43S Plug-in 10 2 TX C NC TX 2 TOP-A433N Antenna...
- Page 8 Safety inputs should now be configured and the gate force tested as required. Please refer to the full manual to complete the commissioning. Should the gates not operate as suggested above, call CAME helpline 0115 921 0430 for technical support.
- Page 9 PROGRAMMED The LED on the new transmitter will fl ash three times to acknowledge it has received the signal from the saved transmitter. Should the transmitter not operate as suggested above, call CAME helpline 0115 921 0430 for technical support.
- Page 10 ZT6: SAFETY SAFETY INPUTS FUNCTIONS > C1 Input, CX Input REOPENING DURING CLOSING • When the automation is in its closing cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its fully open position again.
- Page 11 BY-3500T: ACCESSORIES Code(s) Description RADIO KEYPAD SELECTORS 806SL-0170 SELT1W4G - Surface-mounted, 433.92 MHz radio-frequency keypad selector, 12-keys, with blue backlighting. 25 savable codes and password to access the programming mode. Settable in Rolling Code or Fixed Code mode. RAL7024 Grey colour. 806SL-0180 SELT1W8G - Surface-mounted, 868.35 MHz radio-frequency keypad selector, 12-keys, with blue backlighting.
- Page 12 YOU MAY NOT EVEN PARTIALLY REPRODUCE THIS DOCUMENT CAME RESERVES THE RIGHT TO MAKE ANY CHANGES TO THIS DOCUMENT AT ANY TIME THE DATA AND INFORMATION SHOWN IN THIS CATALOGUE ARE SUBJECT TO CHANGE WITHOUT OBLIGATION TO GIVE PRIOR NOTICE BY CAME S.P.A, E&OE CAME S.p.A.