Music Center: SA-HT700 (GCS) System : SC-HT700 (GCS) Satellite speakers: SB-HT700 (P) Active Subwoofer: SB-WA330 (GCS) 2003 PANASONIC AVC Networks Singapore Pte. Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. Safety Precautions 1.1. GENERAL GUIDELINES 1.
Page 3
insulation barriers, insulation papers shields are properly installed. 3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards. 1.1.1. LEAKAGE CURRENT COLD CHECK 1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used. If this occurs, follow the procedure outlines below: 1.
negative (-) speaker wires. - Be sure to connect only positive (red) wires to positive (+) terminals and negative (black) wires to negative (-) terminals. 7. Disassembly Procedure “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1.
Page 7
Step 2: Remove all screws. Step 3: Remove the Stand Base. Step 4: Remove 5 screws from the speaker bottom. Step 5: Pull the Power/Amp Unit as shown.
Page 8
Step 6: Release the connector CN506 and pull out the Power/Amp Unit. Step 7: Push the Net Frame from two holes inside the unit. Step 8: Remove the Net Frame.
Page 9
Step 9: Remove all the screws. Step 10: Remove the Speaker. Step 11 & 12: Remove all the screws. Step 13: Release the connector CN507. Step 14: Remove the 2 screws.
Page 10
Step 15 & 16: Remove all the screws. Step 17: Place the Power PCB as shown for checking. Checking for AC Inlet PCB. 7.2. Main Component Replacement Procedures 7.2.1. Replacement of the Power IC...
Step 1 & 2: Remove all the screws. Step 3: Desolder the Power IC terminal and replace the component. 8. Connection of the Speaker Wiring 9. Block Diagram 10. Schematic Diagram (All schematic diagrams may be modified at any time with the development of the new technology) Note: - The voltage value and waveforms are the reference voltage of this...
Page 12
unit measured by DC electronic voltmeter (high impedance) and oscilloscope on the basis of chassis. Accordingly, there may arise some error in voltage values and waveforms depending upon the internal impedance of the tester or the measuring unit. - Importance safety notice : Components identified by mark have special characteristics important for safety.
Page 13
- Capacitor values are in microfarads ( F) unless specified otherwise, P= Pico-farads (pF), F= Farads. - Resistance values are in ohms, unless specified otherwise, 1K= 1,000 (OHM). - The marking (RTL) indicates that the Retention Time is limited for this items.
Page 24
AC INLET P.C.B (REP3435G) CAUTION RISK OF ELECTRIC SHOCK AC VOLTAGE LINE. PLEASE DO NOT TOUCH THIS P.C.B FC502 FC501 F1 250V T2AL T502 (POWER TRANSFORMER) L500 JK500 Q516 J500 RLY501 C555 J501 AC IN R589 C557 R578 230V-240V C558 50HZ J502 J503...
Page 25
SCHEMATIC DIAGRAM-1 : MAIN SIGNAL LINE : -B SIGNAL LINE POWER CIRCUIT : +B SIGNAL LINE IC501 C551 IC501 0.01 RSN311W64B-P POWER HIC E501 K4CZ01000027 R501 R513 4.7K R502 C507 18P 4.7K R514 C508 18P R524 120K D501-D502 R506 B0JAPG000019 R516 R526 C510 22P...
Page 26
SCHEMATIC DIAGRAM-2 : MAIN SIGNAL LINE : -B SIGNAL LINE POWER CIRCUIT : +B SIGNAL LINE R597 R594 C564 1200P Q514 R592 R403 R599 Q513 100K C565 R593 R571 C568 R591 R572 3.3K 0.01 6.8K 470K C562 IC502 5600P C0AABB000055 C524 C525 DUAL LOW-NOISE OP AMP...
Page 27
SCHEMATIC DIAGRAM-3 : -B SIGNAL LINE : +B SIGNAL LINE C555 R589 35V4.7 Q516 R578 KRC102MTA SYNC SWITCH CN502 R580 PCONT Q517 POWER CIRCUIT KTC2026 (CP502) ON SYNC R587 VOLTAGE REGULATOR D530 D528 SCHEMATIC 2.7K SYS6V DIAGRAM-2 C559 HELP 0.01 C556 R588 0.01...
Page 28
CN501 7..1 CP502 JK502 LED P.C.B. CN507 SPEAKER JK501 WOOFER H505A/W505 SOLDER SIDE SOLDER SIDE POWER P.C.B. SOLDER SIDE T501(POWER TRANSFORMER) TRANSFORMER P.C.B. T502(POWER TRANSFORMER) AC INLET AC IN JK500 P.C.B. 230~240V 50HZ CN502 SOLDER SIDE 7.
Page 29
IC501 RSN311W64B-P POWER HIC POWER CONTROL CIRCUIT POWER CONTROL/PROTECTION CIRCUIT 12(11) (25) (19) D501 D502 Q506 TO MAIN INTERFACE BLOCK SWITCH (JK700) OF SA-HT500GN-S, Q505 (JK300) OF SA-HT700GN-S SWITCHING SL(R)/SURRL(R) FILTER FILTER JK501(JK502) SURROUND SPEAKER CCH/CENTRE FILTER FILTER JK502 CENTRE SPEAKER FILTER SUBWOOFER...