Page 1
ORDER NO.DSD0401001C1 DVD Video Recorder DMR-E55P / DMR-E55PC Colour (K).......Black Type (S).......Silver Type SPECIFICATIONS 2004 Matsushita Electric Industrial CO., Ltd. All rights reserved.
Unauthorized copying and distribution is a violation of law. 1. Safety precautions 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2.
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5k , 10 watts resistor, in parallel with a 0.15 capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 1 3.
Page 4
whichshould be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
( As shown in 20.2.1. The Main P.C.B. ) NOTE: The lithium battery is a critical component. ( Type No.: CR2354-1GUF Manufactured by Panasonic. ) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.
5. Handling the Lead-free Solder 5.1. About lead free solder (PbF) Distinction of PbF P.C.B.: P.C.B.s (manufactured) using lead free solder will have a PbF stamp on the P.C.B. Caution: - Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher.
Page 7
Description Symbol Trigger input terminal. Zero detection voltage: 0.25V It becomes less than 3V, the mode turns to standby. Bias current feedback input terminal. Switching ON time (min.) ~ (max.) 1.5V ~ 4.5V / 0 sec. ~ 25 sec. In standby mode Oscillation stops:less than 0.8V Oscillation starts: over 1.8V GND terminal...
Page 8
After IC1150 has started, the startup current is cut off. The current of Startup Circuit is supplied as constant current source in IC1150 and as charge current for the capacitor connected between Vcc terminal and GND out side of IC1150 until Vcc reaches 14.4V.
Page 9
The Switching ON width responds to change of F/B Voltage. Standby Function When Z/C Voltage becomes less than 3V, the unit changes to Standby mode. IC1150 Block Diagram Signal name Pin No. Name Symbol Zero Current Det. Feed back Drain Drain 8.
Disc cannot be ejected by OPEN/CLOSE button 8.1. Forcible Disc Eject 8.1.1. When the power can be turned off. 1. Turn off the power and press [STOP] [CH UP] keys on the front panel simultaneously for 5 seconds. 8.1.2. When the power can not be turned off. 1.
9. Service Explorer Confirm “RAM-Drive Last Error” in Service Mode Execute Service Mode 1. Press [STOP], [TIME SLIP] and [OPEN/CLOSE] simultaneously for 5 seconds when P-off. FL Display: *After finishing display “(7). Factor of Drive Error occurring”, press [0] [2] ~[9] [9] keys of the Remote Controller so that 99 memories can be displayed as maximum.
Page 12
(5) Error occurring Disc type is displayed for 5 seconds. (6) Disc Maker's ID is displayed for 5 seconds. Example of Disc Maker's ID: DVD-R Disc FL Display (Disc Disc Maker Country Maker's ID) Panasonic Japan Pioneer Japan Mitsubishi Chemical Japan Corporation Japan...
Page 13
Disc Maker Country Maker's ID) VIVASTAR VIVASTAR Switzerland LG Electronics Korea DVD-RAM Disc FL Display (Disc Disc Maker Country Maker's ID) Panasonic MATSUSHITA Panasonic Japan Maxell Japan PRODISC Prodisc Taiwan OPTDISC OPTDISC Taiwan Taiwan *Since an display is arbitrarily set up by the disk producer side, the above-mentioned display may be changed.
10. Self-Diagnosis and Special Mode Setting 10.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U14, H** and F** are stored in memory and held. Display on FL will be cancelled when the power is turned off or AC input is turned off during self- diagnosis display is ON.
Page 15
Error Diagnosis contents Description Monitor FL display Display Code No error information Initial setting for error code in No display memory (Error code Initialization is possible with error code Displayed is left. initialization and main unit initialization.) Drive hardware error Display appears when drive unit No display error is detected.
10.2. Special Modes Setting Item FL display Key operation Mode name Description Front Key TEST Mode *All the main unit's parameters Press [SKIP (REV)], (include tuner) are initialized. SLIP] and [OPEN keys simultaneously five seconds when is off. Service Mode Setting every kind of modes for When the power servicing.
Page 17
Item FL display Key operation Mode name Description Front Key Aging Perform sequence of modes as * Display following the then When the power Aging Description shown below mode. press [CH DOWN], continually. SLIP] and [OPEN simultaneously for five seconds and than 10 seconds.
Item FL display Key operation Mode name Description Front Key Progressive The progressive setting is The display before When the power initialization initialized to Interlace. execution leaves. mode), press [STOP] [TIME SLIP] simultaneously for seconds. Aging Contents (Example): 10.3. Service Modes Service mode setting: While the power is off, press TIME SLIP, STOP and OPEN / CLOSE simultaneously for five seconds.
Page 19
Item FL display Key operation Mode name Description (Remote controller White Picture White picture is output as *Initial mode is “Interlace”. Press [1] [1] in service Output component Output from AV mode. Decoder. *White picture Switch Interlace/ Press [1] [4] in White (Saturation rate : 100%) Progressive Picture Output mode.
Page 20
Item FL display Key operation Mode name Description (Remote controller RTSC Return in XP L1 input signal is encoded (XP), Initial mode: EE2/ Interlace/ Press [1] [3] in service decoded (XP) and output XP/ Audio 48kHz mode. decoded signal to external (A &...
Page 21
Item FL display Key operation Mode name Description (Remote controller Laser Used Time Check laser used time (hours) of Press [4] [1] in service Indiction drive. mode. (*****) is the used time display in hour. Laser used time ofDVD/ CD in Playback/Recording mode is counted.
Page 22
Item FL display Key operation Mode name Description (Remote controller RAM Drive Last RAM Drive error code display. 1. Error Number is Press [4] [2] in service Error displayed for 5 seconds. mode. *For details about the drive error code, refer to the Service Manual Then press [0] [1] for the specific RAM Drive.
Page 23
Item FL display Key operation Mode name Description (Remote controller Delete the Last Delete the Last Drive Error Press [9] [6] in service Drive Error information stored on the DVD mode. RAM-Drive. Turn on all FL/ All segments of FL and all LEDs All segments are turned Press [5] [1] in service LEDs...
Page 24
Item FL display Key operation Mode name Description (Remote controller Display the Error Display the Error History stored Display reason of error for Press [6] [5] in service History on the unit. 5 seconds. mode. Then press [0] [1] the past 19 error are displayed.
11. Assembling and Disassembling 11.1. Disassembly Flow Chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below. 11.2.
Page 26
11.4. Digital P.C.B. 1. Remove the FFC and a Screw. 2. Lift up Digital P.C.B. slightly so to disconnect Connector to remove Digital P.C.B. CAUTION: When replacing Digital P.C.B., pay attention as below.
Page 27
11.5. Front Panel 1. Remove 3 tabs (A) and 2 tabs (B) in this order. (The tab (A) and (B) should be removed at the same time, respectively.) 2. Move the front panel to front side straight and slowly so to remove it with Connector.
11.6. Front (R) P.C.B. 1. Remove 6 screws and Front Angle. 11.7. DVD-RAM Drive 1. Remove 3 Screws. 2. Pull out DVD-RAM Drive vertically so to remove it with Connector. 11.8. Rear Panel 1. Remove the 5 screws (A) and screw (B). 2.
Page 29
11.8.1. Only Fan Motor 1. Remove the 2 screws. 2. Remove Fan Connector to remove Fan Motor. 11.9. Main P.C.B. 1. Remove the 5 screws (A), Connector (A) and Fan Connector.
2. Remove a Screw (B) and lift up Front Jack portion of Main P.C.B. slightly so to unlock Tab to remove Main P.C.B.. 11.10. Power P.C.B. 1. Remove 3 Screws and Connector (A). 2. Lift up Power P.C.B. a little so to unlock 2 Tabs and slide Power P.C.B.
Extension Cable RFKZ0214 has A/V Output Signal switches. Output signals can be switched from MAIN PCB side or DIGITAL PCB side. When check MAIN PCB, turn switches to MAIN PCB side. When check DIGITAL PCB, turn switches to DIGITAL P.C.B. side. 13.
Turn on the power, and confirm items pointed out. Items pointed out should reappear. Insert RAM disc. The Panasonic RAM disc should be recognized. Enter the EE (TU IN / AV IN - AV OUT) mode. No abnormality should be seen in the picture, sound or operation.
Item Contents Check Item Contents Block noise Distorted sound Crosscut noise Noise (static, background noise, etc.) Picture Sound Dot noise The sound level is too low. Picture disruption The sound level is too high. Not bright enough The sound level changes. Too bright Flickering color Color fading...
Page 37
INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMPOUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT BLACK DROP OUT...
Page 38
INITIAL/LOGO ABBREVIATIONS DACCK D/A CONVERTER CLOCK DEEMP DEEMPHASIS BIT ON/OFF DEMPH DEEMPHASIS SWITCHING DIG0~UP FL DIGIT OUTPUT DATA INPUT DMSRCK DM SERIAL DATA READ CLOCK DMUTE DIGITAL MUTE CONTROL DROP OUT DOUT0~UP DATAOUTPUT DATA SLICE RF (BIAS) DRPOUT DROP OUT SIGNAL DREQ DATA REQUEST DRESP...
Page 39
INITIAL/LOGO ABBREVIATIONS IECOUT IEC958 FORMAT DATA OUTPUT IPFRAG INTERPOLATION FLAG IREF I (CURRENT) REFERENCE ISEL INTERFACE MODE SELECT LDON LASER DIODE CONTROL LASER POWER CONTROL LRCK L CH/R CH DISTINCTION CLOCK MA0~UP MEMORY ADDRESS MEMORY CLOCK MCKI MEMORY CLOCK INPUT MCLK MEMORY SERIAL COMMAND CLOCK...
Page 40
INITIAL/LOGO ABBREVIATIONS READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK...
Page 41
SYSTEM CLOCK INITIAL/LOGO ABBREVIATIONS TRACKING ERROR TIBAL BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 TPSN OP AMP INPUT TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSSSIGNAL TRON TRACKING ON TRSON TRAVERSE SERVO ON INITIAL/LOGO ABBREVIATIONS VBLANK...
INITIAL/LOGO ABBREVIATIONS X' TAL XALE X ADDRESS LATCH ENABLE XAREQ X AUDIO DATA REQUEST XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XH INTERRUPTREQUEST X' TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE...
22. Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufactures specified parts shown in the parts list.
Page 48
Ref. No. Part No. Part Name & Description Remarks K2KA6CA00001 AV CORD K2CB2CB00006 AC CORD VJA1125 RF COAXIAL CABLE K2KZ2BA00001 RPQF0220 ACCESSORY CASE RQF5321 FAN BAG ASS’Y RQF5397 FAN BAG ASS’Y (PC) A6-1 RQT7301-P OPERATING INSTRUCTIONS <IA> A6-1 RQT7395-C OPERATING INSTRUCTIONS <IB>(PC) A6-2 RQCB0833...
Page 64
IC Pin Terminal Chart ( TC 1 - TC 6 ) IC Pin Terminal Chart ( TC7 - TC10 ) IC3404 / AVENC&RTSC IC3402 / SDRAM IC3404 / AVENC&RTSC FP3401 (DVD RAM) IC50001 / SDRAM IC6001 / AV DEC&MAIN CPU IC6005 / W-MEMORY IC6001 / AV DEC&MAIN CPU SIGNAL NAME...
Page 65
SA0 - SA25 ADDRESS BUS LINE (TC12, TC14-1, TC15-1, TC17, TC18-1) SD16 - SD31 DATA BUS LINE (TC14-2, TC15-2, TC18-2 ) 14-1 15-1 18-1 14-2 15-2 18-2 IC3404 / AVENC&RTSC IC6701 / GLUE IC6001 / AVDEC&MAIN CPU IC6004 / BUFFER IC6003 / LOADER IC6701 / GLUE IC6003 / LOADER...
Page 67
A/V OUT REAR JACK MIX L OUT OUT-L LINE P9001 P7402 MIXLOUT DM P9001 P7402 MIXROUT DM MIX R OUT OUT-R FROM DIGITAL BLOCK SECTION JK3903 DIGITAL AUDIO OUT P9001 P7402 IECOUT IEC OUT OPTICAL DMR-E55P/PC ANALOG AUDIO BLOCK DIAGRAM...
Page 68
6V47 R4418 XADC PD DMR-E55P/PC NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Audio I/O Section (Digital P.C.B.(4/4)) IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 69
R4015 R4016 100K 100K K4001 VWJ0023=5 L1 IN L L1 IN R L3 IN L L3 IN R DMR-E55P/PC R4004 R4003 R4002 R4001 100K 100K 100K 100K Audio Main Section (Main P.C.B.(4/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Schematic Diagram (A) IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 70
X7502 32.768KHz (REAL TIME CLK) XC OUT XT MUTE TO AUDIO BLOCK SEC. XT MUTE (QR4001,4004) SYNC IN SLICER VIDEO CV IN FROM VIDEO X SW+5.2V BLOCK SECTION L1 SWIDE L123 SWIDE B7501 DMR-E55P/PC BACK UP TIMER BLOCK DIAGRAM BATTERY...
Page 71
COUT A CPNCIN DM P7402 P9001 TO DIGITAL Y/V OUT A BLOCK SECTION V YIN DM P7402 P9001 C2 IN CPN 2C IN BIAS Y2 IN CPN 2Y IN CLAMP DMR-E55P/PC C/S DET2 S-VIDEO C/S DET2 ANALOG VIDEO BLOCK DIAGRAM...
Page 72
Ref.No.4400 SERIES Sub Power Supply Ref.No.1500 SERIES Main Net Ref.No.7400 SERIES Digital P.C.B.connect circuit P7402 Main WORKING P.C.B. Video I/O Ref.No.3000,3900,4900 SERIES MEMORY DMR-E55P/PC BUFFER LOADER 16bit/128M- Audio Main Ref.No.4000 SERIES 16bit/64M 16bit/64M SDRAM SDRAM SDRAM Digital Block Diagram Timer Ref.No.7500,7600 SERIES...
Page 73
DIGITAL P.C.B. OVER VIEW *IC6702 is not supplied in the form of an individual part. When replacing, be sure to replace the digital p.c.b. and not IC6702 singly. DMR-E55P/PC (COMPONENT SIDE) DIGITAL P.C.B. (COMPONENT SIDE) (E55P:REP3717B,E55PC:RFKBE55PC)
Page 74
DIGITAL P.C.B. OVER VIEW DMR-E55P/PC (FOIL SIDE) DIGITAL P.C.B. (FOIL SIDE) (E55P:REP3717B,E55PC:RFKBE55PC)
Page 75
DIGITAL P.C.B. Integrated Circuit CKC93 F CKG23 C CL6715 F FL3431 C C4416 F R4426 F R50006 F RX6014 IC3401 C CKC94 F CKG25 C CL6716 F FL3433 C C4417 F R4427 F R50007 F RX6015 IC3402 C CKC95 F CKG26 C CL6717 F FL3434 C C4418...
Page 76
XCAS D EN:AV Encoder/RTSC Section(Page: R3414 C3441 C3440 R3449 MC:AV Decoder/Main CPU Section(Page: ACLKSEL 6V100 6800 X3401 AI:Audio I/O Section(Page: H0J270500069 ENCLRCK C3407 C3408 R3451 ENCDATA ENCBCK DMR-E55P/PC AV Encoder/Real Time Stream Control (RTSC) Section (Digital P.C.B.(2/4)) Schematic Diagram (EN)
Page 77
< D1.5V > FL3420 F1H0J4740004 < D3.3V > < D3.3V > R3430 22 R3421 DMR-E55P/PC AV Encoder/Real Time Stream Control (RTSC) Section (Digital P.C.B.(2/4)) Schematic Diagram (EN) DMR-E55P/PC AV Encoder/Real Time Stream Control (RTSC) Section (Digital P.C.B.(2/4)) Schematic Diagram (EN)
Page 78
R3472 RX3427 RX3428 10KX4 10KX4 DMR-E55P/PC AV Encoder/Real Time Stream Control (RTSC) Section (Digital P.C.B.(2/4)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE DMR-E55P/PC AV Encoder/Real Time Stream Control (RTSC) Section (Digital P.C.B.(2/4))
Page 79
FRONT (R) P.C.B. DMR-E55P/PC FRONT (R) P.C.B. (REP3713A)
Page 80
CH-UP TIME-WARP PLAY DMR-E55P/PC NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Front (R) IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 83
SA25 SA25 SA22 SA22 < D3.3V > DMR-E55P/PC DMR-E55P/PC Glue Net Section (Digital P.C.B.(1/4)) Glue Net Section (Digital P.C.B.(1/4)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Schematic Diagram (GN) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 84
Ref.No.6000,50000 SERIES Sub Power Supply Ref.No.1500 SERIES D 1.8V D 1.8V Main P.C.B. Audio I/O Ref.No.4400 SERIES Video I/O Ref.No.3000,3900,4900 SERIES P.C.B. D 1.8V D 1.8V Glue Net Ref.No.6700,9000 SERIES Audio Main Ref.No.4000 SERIES Timer Ref.No.7500,7600 SERIES DMR-E55P/PC Interconnection Schematic Diagram...
Page 91
NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR XIRQ0 FL50006 3300 R50011 22K ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. F1H0J4740004 R6018 < D3.3V > DMR-E55P/PC AV Decoder/Main CPU Section (Digital P.C.B.(3/4)) Schematic Diagram (MC) DMR-E55P/PC AV Decoder/Main CPU Section (Digital P.C.B.(3/4)) Schematic Diagram (MC)
Page 92
C7406 C7407 TO FRAME GND ZJ7407 K9ZZ00000424 DMR-E55P/PC ZJ7408 K9ZZ00000424 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Main Net Section (Main P.C.B.(2/5)) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 93
NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. COLD IMPORTANT SAFETY NOTICE: DMR-E55P/PC COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. Main Power WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE.
Page 94
IC1302 COUPLER (REG.+5V) DR+5V P1102 P1502 P1501 P102 VOUT (TO DVD RAM DRIVE) 16,17 QR1304, QR1302 QR1303 QR1308 Q1201 QR1200 D1154 PHOTO COUPLER DR P ON P1102 P1502 IC7501- P SAVE P1102 P1502 IC7501- COLD DMR-E55P/PC Power Supply Block Diagram...
Page 95
IC1507 IC3409 (REG.D+5V) (REG.D+3.3V) VOUT JK3903- REG.D+5V P7402 P9001 VOUT IC3406(+3.3V) CONT STBY POWER ON IC7501- X SW+13V IC7506- IC4005 (REG.AU+9V) VOUT IC4001- T7501 IP7501 (POWER TRANS.) UNREG+38V TO TU7401- DMR-E55P/PC DMR-E55P/PC Power Supply Block Diagram Power Supply Block Diagram...
Page 98
25V100 VWJ0023=5 JC P ON DMR-E55P/PC NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Sub Power Section (Main P.C.B.(1/5)) IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 100
UNR521200L D3.3V (INV.) <XSW 5.2V> X SW 5.2V <XSW 5.2V> <NSW 5V> DMR-E55P/PC DMR-E55P/PC Timer Section (Main P.C.B.(5/5)) Timer Section (Main P.C.B.(5/5)) NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR Schematic Diagram (T) Schematic Diagram (T)
Page 102
LB3927 J0JCC0000103 R3927 R3926 C3902 C3901 0.01 DMR-E55P/PC DMR-E55P/PC Video I/O Section (Main P.C.B.(3/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER Video I/O Section (Main P.C.B.(3/5)) Schematic Diagram (V) IS SHOWN IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 103
IC1502 IC1505 IC1506 Ref No. MODE PLAY STOP IC1507 IC1508 IC1509 Ref No. MODE PLAY STOP Ref No. IC1510 MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP Ref No. IC3001 MODE PLAY STOP IC3001 Ref No.
Page 104
IC4001 Ref No. MODE PLAY STOP IC4004 IC4005 IC7404 Ref No. MODE 13.4 PLAY 13.4 STOP 13.4 Ref No. IC7501 MODE PLAY STOP IC7501 Ref No. MODE PLAY STOP IC7501 Ref No. MODE PLAY STOP IC7501 Ref No. MODE PLAY STOP IC7501 Ref No.
Page 105
P9001 Ref No. MODE PLAY STOP P9001 Ref No. MODE PLAY STOP P9001 Ref No. MODE PLAY STOP P9001 Ref No. MODE PLAY STOP P9001 Ref No. MODE PLAY STOP...
19 Schematic Diagram 19.1. Interconnection Schematic Diagram TU7401 P7402 P9001 U/V TUNER CPNCIN DM CPNCIN DM V YIN DM V YIN DM DGND DGND DGND DGND G/CY IN G/CY IN RGB CPSVIN RGB CPSVIN DGND DGND DGND DGND B/CB IN B/CB IN DGND DGND...
Page 108
D 3.3V Main Net Ref.No.7400 SERIES D 3.3V D 3.3V Sub Power Supply Ref.No.1500 SERIES D 1.8V D 1.8V Main Video I/O Ref.No.3000,3900,4900 SERIES P.C.B. D 1.8V D 1.8V Audio Main Ref.No.4000 SERIES Timer Ref.No.7500,7600 SERIES DMR-E55P/PC Interconnection Schematic Diagram...
Page 111
19.3. Sub Power Section (Main P.C.B. (1/5)) Schematic Diagram (P) TO P1102 POWER P.C.B. P1502 LB1501 J0JHC0000032 X SW13V LB1503 J0JHC0000032 X SW 5.8V X SW 5.8V C1541 C1543 10V470 25V220 D1501 R1503 DR P ON MA2C165001VT P SAVE DR12V DR12V DRGND R1502...
Page 112
C1531 C1537 10V47 25V100 DMR-E55P/PC E PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Sub Power Section (Main P.C.B.(1/5)) AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Schematic Diagram (P)
Page 113
19.4. Main Net Section (Main P.C.B. (2/5)) Schematic Diagram (M) TO P9001 DIGITAL P.C.B. (GLUE NET) P7402 D1.2V D1.2V X SW 5.8V D1.2V X SW 5.8V R7403 D1.5V LB7413 ERJ3GEY0R00V D1.2V X SW 5.8V X SW 5.8V D1.5V ANA5V ANA5V D1.5V D1.5V L7401 G0A220G00018...
Page 114
K7407 VWJ0023=12.5 VWJ0023=12.5 DMR-E55P/PC Main Net Section (Main P.C.B.(2/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 115
19.5. Video I/O Section (Main P.C.B. (3/5)) Schematic Diagram (V) AUDIO VIDEO LINE LINE IN3(R) IN1(R) IN3(L) IN1(L) L3 IN L1 IN CPN L3 IN CPN L1 IN JK3901 K1U822B00003 (EXTERNAL A/ R3903 R3906 R3907 R3904 C3912 R3908 L3 IN R 0.01 L1 IN R L3 IN L...
Page 116
C 1 IN S1/S2 DET1 DRV GND2 C3012 0.01 Y 1 IN 21 R3032 K3002 C3020 VWJ0023=5 0.01 C3011 0.01 C3016 0.01 C3015 0.01 C3014 0.01 R3033 10K R3031 C3021 0.01 DMR-E55P/PC Video I/O Section (Main P.C.B.(3/5)) Schematic Diagram (V)
Page 117
K3001 R3028 C3001 560P DMR-E55P/PC NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER Video I/O Section (Main P.C.B.(3/5)) IS SHOWN IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 118
LB4912 LINE IN 2(R) J0JCC0000103 LB4911 J0JCC0000103 LINE IN 2(L) LB3929 J0JCC0000103 CPS L2 IN R3929 SYNC IN LB3928 J0JCC0000103 CPN L2 IN R3928 LB3927 J0JCC0000103 R3927 R3926 C3902 C3901 0.01 DMR-E55P/PC Video I/O Section (Main P.C.B.(3/5)) Schematic Diagram (V)
Page 119
19.6. Audio Main Section (Main P.C.B. (4/5)) Schematic Diagram (A) X SW 5.8V X SW 13V K4008 VWJ0023=5 C4046 C4049 C4045 6V470 VOUT IC4004 C0CBCDC00026 (REG.AU+5V) C4047 R4077 POWER ON K4005 VWJ0023=10 R4042 0 MIXLOUT DM MIXROUT DM C4028 R4043 R4075 R4074 16V1...
Page 120
XDMUTE (MUTE) K4001 VWJ0023=5 DMR-E55P/PC Audio Main Section (Main P.C.B.(4/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Schematic Diagram (A) IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 124
FANDCOUT R7603 18K R7601 FANLOCK D3.3V <XSW 5.2V> X SW 5.2V DMR-E55P/PC Timer Section (Main P.C.B.(5/5)) NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR Schematic Diagram (T) ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 125
19.8. Glue Net Section (Digital P.C.B. (1/4)) Schematic Diagram (GN) TO P7402 MAIN P.C.B. (MAIN NET) P9001 D1.2V D1.2V X SW 5.8V DGND D1.2V < D3.3V X SW 5.8V D1.5V D1.2V R6731 X SW 5.8V CKG79 CKG75 2200 D1.5V ANA5V ANA5V D1.5V D1.5V...
Page 128
SA25 SA22 SA22 DMR-E55P/PC Glue Net Section (Digital P.C.B.(1/4)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 130
RX3416 22X4 DQM0 D XCS0 D GN:Glue Net Section(Page: R3448 XRAS D 5600 XCAS D EN:AV Encoder/RTSC Section(Page: R3449 MC:AV Decoder/Main CPU Section(Page: 6800 AI:Audio I/O Section(Page: DMR-E55P/PC AV Encoder/Real Time Stream Control (RTSC) Section (Digital P.C.B.(2/4)) Schematic Diagram (EN)
Page 134
2 4 6 8 RX3427 RX3428 10KX4 10KX4 DMR-E55P/PC AV Encoder/Real Time Stream Control (RTSC) Section (Digital P.C.B.(2/4)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE Schematic Diagram (EN) SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 138
< D1.2V > FL50005 F1H0J4740004 768FS2 CLK54A1 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR FL50006 R50011 22K ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. F1H0J4740004 DMR-E55P/PC AV Decoder/Main CPU Section (Digital P.C.B.(3/4)) Schematic Diagram (MC)
Page 140
C4416 C4415 6V47 R4418 DMR-E55P/PC THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Audio I/O Section (Digital P.C.B.(4/4)) IST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Schematic Diagram (AI)
19.12. Front (R) Schematic Diagram IR7801 B3RAD0000071 (REMOTE CON.SENSOR) R7801 C7801 R7802 D7801 B3ABA0000396 TO P7504 MAIN P.C.B. TIME-WARP (TIMER) P7801 KEYIN2 KEYIN3 QR7801 KEYIN1 UNR2214 TWARP LED TIME WARP LED DRIVE N SW 5V R7809 2700 R7817 2700 R7818 2200 S7801 S7802 S7809...
Page 142
EVQ11G07K EVQ11G07K EVQ11G07K EVQ11G07K STOP SKIP-R CH-UP TIME-WARP PLAY DMR-E55P/PC ART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Front (R) D MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Schematic Diagram...