[Standby Mode]; [Schedule] - Panasonic PT-DZ21KU Operating Instructions Manual
Hide thumbs
Also See for PT-DZ21KU:
- Brochure (8 pages) ,
- Operating instructions manual (179 pages) ,
- Specification (19 pages)
Table of Contents
Advertisement
10) Set [BRIGHTNESS CONTROL GAIN]
of all projectors to 100%.
11) Set [BRIGHTNESS CONTROL GAIN]
of the darkest projector to 90%.
12) Adjust [BRIGHTNESS CONTROL
GAIN] to match the [BRIGHTNESS
CONTROL GAIN] set to 90% of the
other projectors.
13) Set [MODE] in [BRIGHTNESS
CONTROL SETUP] of all projectors to
[AUTO], and [LINK] to [GROUP A].
14) Select [APPLY] in [BRIGHTNESS
CONTROL SETUP] on all projectors
and press the <ENTER> button.
▶
z Luminance control starts.
Note
z Brightness is automatically corrected each time the
lamp blinks when the power is switched on or off.
z Adjust luminance control again when variation in
brightness has increased or a lamp is replaced.
[STANDBY MODE]
Set the power consumption during the standby.
1) Press ▲▼ to select [STANDBY MODE].
2) Press ◀▶ to switch [STANDBY
MODE].
▶
z The setting will change as follows each time
you press the button.
[NORMAL]
Note
z When set to [ECO], network functions and <SERIAL
OUT> terminal, and some RS-232C commands are
not available during standby. The lighting for the
connecting terminals and control panel does not
turn on.
z When an error or warning occurs, a self diagnosis
is displayed on the control panel regardless of the
[STANDBY MODE] setting. (
z When set to [ECO], the time taken to start display
may be approximately ten seconds slower than
compared to when set to [NORMAL].
[ECO]
page 27)
[PROJECTOR SETUP] menu
[SCHEDULE]
Set the command execution schedule for each day of
the week.
1) Press ▲▼ to select [SCHEDULE].
2) Press ◀▶ to switch [SCHEDULE].
▶
z The setting will change as follows each time
you press the button.
[ON]
Note
z If [SCHEDULE] is set to [ON], the setting for
[STANDBY MODE] is automatically set to
[NORMAL] and cannot be changed. Even if
[SCHEDULE] is then set to [OFF] when in this
state, the setting of [STANDBY MODE] remains at
[NORMAL].
■ How to assign a program
▶
3) Select [ON] in Step 2), and press the
<ENTER> button.
▶
z The [SCHEDULE] screen is displayed.
4) Select and assign program to each day
of week.
z Press ▲▼ to select the day of week, and press
▶
◀▶ to select a program number.
▶
z You can set the program from No.1 to No.7. "-
- -" indicates that the program number has not
been set yet.
■ How to set a program
▶
You can set up to 16 commands to each program.
3) Select [ON] in Step 2), and press the
<ENTER> button.
▶
z The [SCHEDULE] screen is displayed.
4) Press ▲▼ to select [PROGRAM EDIT].
5) Press ◀▶ to select a program number
and then press the <ENTER> button.
6) Press ▲▼ to select a command
number and press the <ENTER>
button.
z You can change the page using ◀▶ .
▶
7) Press ▲▼ to select [TIME] and press
the <ENTER> button.
8) Press ◀▶ to select hour and minute,
and press ▲▼ or the number (<0> to
<9>) buttons on the remote control
to set a time, and press the <ENTER>
button.
9) Press ▲▼ to select [COMMAND].
[OFF]
ENGLISH - 109
Hide quick links:
Advertisement
Table of Contents
