Download Print this page

Kenmore 67102 Use & Care Manual page 10

Electronic dryer

Hide thumbs Also See for 67102:

Use & care manual (40 pages)

Table Of Contents

Table of Contents

Advertisement

Available languages

EN

Enlarged version

Vacahon, storage, and moving care

Install

and store your dryer where

it will not freeze.

If storing

or moving

your dryer during

freezing

weather,

winterize

it.

Non=Use or Storage Care

Operate

your dryer only when you are at home.

If you will

be on vacation

or not using your dryer

for an extended

period

of time, you should:

1. Unplug

dryer or disconnect

power.

2. Clean

lint screen. See "Cleaning

the Lint Screen."

Moving

Care

For power

supply cord-connected

dryers:

1. Unplug

the power

supply cord.

2. Make

sure leveling

legs are secure in dryer

base.

3. Use tape

to secure dryer door.

Electrical

Shock

Hazard

Disconnect

power

before

servicing.

Replace

all parts

and panels

before

operating.

Failure

to do so can result

in death

or electrical

shock.

For direct=wired

dryers:

1. Turn off power

at fuse or breaker

box.

2. Disconnect

wiring.

3. Make

sure leveling

legs are secure in dryer

base.

4. Use tape

to secure dryer door.

Reinstaillng

the Dryer

Follow

the "Installation

Instructions"

to locate,

level,

and connect

the dryer.

F

Changing

the drum light

(on some

models)

l° Unplug

dryer

or disconnect

power.

2. Open

the dryer door. Locate the light bulb cover on the

back wall of the dryer. Using a Phillips-head

screwdriver,

remove

the screw located

in the lower right-hand

corner

of the cover. Remove the cover.

3. Turn bulb counterclockwise.

Replace

the bulb with a

lO-watt

appliance

bulb only. Replace

the cover and

secure with the screw.

4. Plug into a grounded

outlet

or reconnect

power.

fChanging

the Auto Cycle Settings

to Increase Drying

Time

If all your loads on all Auto cycles

are consistently

not as dry

as you would

like, you may change

the default

settings

to

increase the default

dryness

level.

Your automatic

drying

settings

can be adjusted

to adapt

to different

installations, environmental

conditions,

or

personal

preference.

This change

is retained

and will affect

all of your Automatic

cycles, not just the current

cycle!load.

There are 3 drying

settings,

which are displayed

using

the Cycle Status lights (Wet, Damp,

Cool Down LEDs)

1

Factory

preset dryness

level.

2

Slightly

drier

clothes,

15% more drying

time.

3

Much drier clothes,

30%

more drying

time.

To change the drying settings (on same models):

NOTE:

The settings

cannot

be changed

while

the dryer

is running

or paused.

The dryer

must be in standby

mode

(the power

button

is off) to adjust the default

settings.

1. Before

starting

a cycle, press and hold the DRY TEMP

button

for 6 seconds.

2. Press the DRY TEMP button

to select the dryness

level

shown in the cycle status light display:

Wet

light

on = level 1, Wet

and Damp

lights on = level 2, and

Wet,

Damp,

and Cool Down lights on = level 3.

3. Press START/PAUSE

to save the new dryness

level

setting.

I0

Table of Contents

Advertisement

Table of Contents

Related Products for Kenmore 67102

This manual is also suitable for:

77102 C66112 C76112