Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Service Hints How to remove the backcover Remove the 20 [21] fixing screws. (see Fig.5) SCREWS SCREWS Fig.5 How to remove the Pedestal assembly Lay the main unit face down. (see Fig.6) Remove the 4 fixing screws and the pedestal assembly. (see Fig.7) SCREWS Fig.7 Fig.6...
Chassis Board Layout G-BOARD P-BOARD A-BOARD M-BOARD V-BOARD Board Name Function A-Board AV Terminal, AV Switch, Sound Processor, Speaker out, TV tuner, PC, SD,Global Core, HDMI, IDTV Processor, D/A Converter, Peaks Lite 2 P-Board Main Input, Power Supply, Power Supply Regulator, Speaker out G-Board Side AV Terminal V-Board...
Setting Inspection Voltage Confirmation Confirm the following voltages: P board Description Test point Position Normal mode Stand by mode Active stand by mode Sound_Vcc TP7050 P7, pin 1,2 18V +/- 1V Max 3V Max 3V BT_30V TP7060 P7, pin 5 31V +/- 1V Max 3V 31V +/- 1V...
(-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button. TX-37LZD80 37FHD Panasonic 2008LCD Self Check Complete 1d34 O.K. PEAKS-SOFT 1.011...
Power LED blinking timing chart Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit. Blinking Blinking timing Contents...
Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu How to enter SERVICE While pressing (-/v) button on the TV unit, press on the remote control for 3 times within 2 seconds.
SERVICE SERVICE Peaks SOFT 1.011 OPTION 1 Key Command ADJUST Peaks EEP 01.03.0006 OPTION 2 S e r v i c e 1 WB-ADJ LSI DATA 11.22.33 OPTION 3 OPTION STBY SOFT 1.01.00 Model ID SRV-TOOL STBY EEP 1.03.01 03111100 •...
Option Bytes Description OPTION1 Speed ATP Slow (1) / Fast (0) TXT Ch ON (1) / OFF (0) ID-1 ON (1) / OFF (0) Macrovision Auto evaluate ON (1) / OFF (0) SRS Surround ON (1) / OFF (0) Teletext Top OFF (1) / ON (0) Equalizer Not use...
Adjustment Method Sub-Contrast/White Balance Adjustment Instrument Name Connect to Remarks Remote controller Correlation can be also taken by LCD WB meter (Minolta CA-210 or equivalent) CS-1000A or equivalent Comunication jig Computer for external control Procedure Remarks Let the panel standfor more than 3 hours at more than 20 °C.
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List. (UK) (CONTINENTAL)
Page 23
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List. Difference for 37’’...
Replacement Parts List Important Safety Notice Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order. RTL (Retention Time Limited) Note: The marking (RTL) indicates that the Retention Time is Limited for this item.
Page 40
Cct Ref Parts Number Description Cct Ref Parts Number Description RELAYS TPD0E2003 BOTTOM CUSHION L/C/R INSTRUCTION BOOKS RL7001 K6B1AGA00043 RELAY RL7030 K6B2ADA00007 RELAY TQB0E0571A GERMAN TQB0E0571B DUTCH DIFFERENCES FOR MODEL TX--32LZD80 TQB0E0571C ITALIAN TQB0E0571D FRENCH EXPLODED VIEW TQB0E0571E SPANISH TQB0E0571F SWEDISH A-32LZD80 A P.C.B.
Page 41
Cct Ref Parts Number Description Cct Ref Parts Number Description INSTRUCTION BOOKS I.C.s TQB0E0570-1 ENGLISH IC8601 X24C37LZD80F EEPROM PL2 I.C.s TERMINALS AND LINKS IC8601 X24C37LZD80 EEPROM PL2 K1PY51Y00006 LVDS FFC TERMINALS AND LINKS A1-V1 TXJ/V10NDA A1-V1 WIRE A11-M11 TXJM110NDA A11-M11 WIRE K1PY51Y00006 LVDS FFC P2-CN501 TXJ/P20NDA...
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM (Ω) (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.