Table of Contents
Advertisement
32LC50C
32LX50C
37LC50CB
32LC50CB
32LX50CS
42LB50C
32LC50CS
37LC50DC
42LC50C
Integrated TVs
Setup & Operation Guide
for
Commercial Mode
Note: All features shown within this guide may not be
available on all models.
Experienced Installer
Master TV Setup
page 6
Cloning Information
pages 7-8-9
©
Copyright 2008, LG Electronics U.S.A., Inc.
Advertisement
Table of Contents
Troubleshooting
Related Manuals for LG 206-4071P
Summary of Contents for LG 206-4071P
- Page 1 Integrated TVs Setup & Operation Guide Commercial Mode Note: All features shown within this guide may not be available on all models. Experienced Installer Master TV Setup page 6 Cloning Information pages 7-8-9 © Copyright 2008, LG Electronics U.S.A., Inc.
-
Page 2: Installer Overview
LG Installer Remote You will need an LG Installer remote control similar to the one shown to the right. The installer remote must have a “Source” but- ton or its equivalent. The remote shown in this manual has “INPUT”... -
Page 3: Table Of Contents
TV. • For any additional information, contact your LG representative. Note: Design and specifications are subject to change without prior notice. Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. For Customer Support/Service please call: 1-888-865-3026 www.lgcommercial.com... -
Page 4: Typical Installer's Remote Control
Use the MODE button to select TV and put installer remote into TV operating mode. Notes: This remote is supplied with the TV. This typical LG multi-brand remote control is shown for reference. See next page for typical key functions in TV mode. -
Page 5: Remote Key Functions
Remote Control Key Functions. To put remote into TV operating mode, select TV with the MODE key. Notes: This remote is supplied with the TV. This typical LG multi-brand remote control is shown for reference. Follow the instructions provided on the next page to access the Installer menus. -
Page 6: Commercial Mode Setup
Commercial Mode Setup for Master TV This page provides an overview of the TV configuration. See the pages listed below for more specific, detailed instructions at each step; how to access and use the Installer menu etc. Note 1: Disconnect all Aux inputs. Under certain conditions, EZ Scan (Channel search) is disabled if there is an Aux input active. -
Page 7: Master Tv Cloning Connections And Cloning Overview
Connections for the LT2002 Clone Programmer to Learn the TV Master TV Setup Antenna or CATV Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer device will be damaged. Notes: It is assumed that the TV is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, see above and next page. -
Page 8: Cloning Learning Setup
Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I. input capability. After the time is copied to the Clone programmer, the current time can then be transferred to another TV. -
Page 9: Cloning Connections/Teaching Setup
Teaching the Master Setup to Another TV Connections for the LT2002 to Teach another TV the Master Setup Antenna or CATV Teach Master TV’s Setup to the target TV After learning is complete, remove the M.P.I. cable from the master TV and connect it to the target TV that you want to copy the master TV’s setup into. -
Page 10: Installer Menu
Installer Menu Use the Installer’s Menu to set up or change operational settings. See more detailed descriptions of the Installer menu items on the following pages... Accessing the Installer’s Menu Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remote control. - Page 11 Installer Menu Items 035 through 118 Menu Item Function Value Range Default Value COMPPORT EN. YPrPb EN. REAR AUX EN AUTO CAMPORT STRT AUX SRCE AUX STATUS DIS. CH-TIME M. EN. CH-T COL. FOR. CH-TIME BCK. CH-TIME CH NOT AVBLE REVERT CH UPN MSB 0 ~ 255...
- Page 12 Installer Menu Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The POWER MANAGE function is for saving energy.
- Page 13 011 - KEY DEFEAT (Keyboard Defeat) If set to 1, key defeat prevents the end user from accessing the on- screen menus with the display front panel—MENU, SELECT, and Left / Right arrow keys do not function. If set to 0, those keys do function. NOTE: The menus can always be accessed by pressing MENU on the remote.
-
Page 14: Installer's Menus
Installer Menu Detailed Descriptions of Installer Menu Items 047 - AUX STATUS Set to 1 for M.P.I. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX identification change. Controls M.P.I. status channel response for AUX inputs. 053 - DIS. - Page 15 093 - RJP AVAILABLE (Remote Jack Pack Available) 0 = Remote jack pack is not available or disabled. 1 = Series 100 RJP, HDMI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI. Audio stream is expected from HDMI source. If no audio is pres- ent, no audio will be heard.
-
Page 16: Clonable Menu Features Chart
Reference: Clonable Menu Features Menu /Sub Menu Features Setup SET ID Audio Audio Language EZ SoundRite EZ sound Balance Treble Bass Front Surround TV Speaker Time Auto Clock Auto Off Note: Video Menu and other feature settings are not clonable on all TVs. End user has access to EZ Picture, EZ Sound and Ratio on user remote control. - Page 17 Reference: Procedures for adding Channel Label Icons/Custom Channel Labels Adding Channel Icons and Labels in the 2-5-4 + Menu Mode Editing/Adding Channel ICONs and/or Labels If there is no pre-assigned ICON, you can make a custom chan- nel label of up to 7 characters to help in identifying the chan- nel or network.
-
Page 18: Editing Channel Icons/Adding Ch Labels 2-5-4 + Menu Mode 17 Detailed Instructions For Making A Master Tv
TV Master TV setup. You will also need an LG Installer remote control similar to the one shown in the front of this manual. The installer remote must have a “Source”... -
Page 19: Software Updating Procedure
Procedure for Checking Software Version The software version of the TV may be checked by accessing the INSTALLER MENU. To do this, press the MENU button repeatedly until the menu display ceases to respond to MENU key presses. Then, press "9", "8", "7", "6", "ENTER/SELECT". PTC INSTALLER MENU INSTALLER SEQ UPN 000-000-000-000... -
Page 20: Camport Auto Sense Operation
TV Camport Auto Sense Operation The CAMPORT Auto Sense function is enabled when: 1. Installer Menu Item 34, CAMPORT EN is set to 1 AND 2. Installer Menu Item 40, AUTO CAMPORT is enabled (1). Selectable= Can be accessed with INPUT key, direct access, etc. Auto Sense= Switches to this input when connector is inserted. -
Page 21: Aux Input Configuration
Troubleshooting Some quick and easy tips to resolving problems Symptoms Possible Cause(s) Software Problems Cannot direct enter Channel not included in channel channel number or scan in TV controller. “No Signal” appears. 206-4071 TV Aux Input Configuration / Troubleshooting Possible Solution(s) After 2-5-5 + MENU, only channels included in TV controller will appear. -
Page 22: Troubleshooting
-Move remote closer to TV’s IR receiver or darken room. -Replace batteries. -Check that “+” and “-” match in battery compartment. -Dim room light. -Requires compatible Installer remote, contact your LG dealer. -Press MUTE or use Volume Up key to increase sound level. -Try a different channel. See Page(s) -
Page 23: Cloning Troubleshooting
Possible Solution(s) - Press Reset on clone programmer, redo teach/learn. (Teach/Learn should take a minimum of 1 minute.) - Only use an LG Installer remote to operate clone programmer with TV. - Connect M.P.I. cord properly, assure good connection. - TV must be powered On for clone to work. -
Page 24: Troubleshooting Flow Chart
Troubleshooting Flow Chart Controller Quick Check 'STATUS' LED on Connected to Analog Board AC Power Blinking Red LED 1. Bad Analog Board. on TV 2. Bad Digital Board. Cycle the power by removing and re-connecting the AC power cord. Observe the 'POWER' LED and TV screen as soon as AC power is re-applied. -
Page 25: Commercial Mode Check
Press the "On/Off" key on the front panel. The On/Off key is always operational. you get a response Leave TV set On Go to Installer menu by pressing "MENU" until the TV stops responding. TV stop responding or continue to respond Continued respond TV is not in Commercial Mode... -
Page 26: Rjp Mode Configuration
Reference: RJP Mode Configuration P A G E 2 6 206-4071... -
Page 27: Glossary Of Terms
A list of definitions for some of the words found in this guide 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. -
Page 28: Back Cover
For Customer Support/Service Please call: 1-888-865-3026 www.lgcommercial.com Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue Englewood Cliffs, NJ 07632 206-4100 © Copyright 2008, LG Electronics U.S.A., Inc. Issue*...