hit counter script
  1. Manuals
  2. Brands
  3. JVC Manuals
  4. TV VCR Combo
  5. TV 13142
  6. Service manual

Electrical Adjustments; Basic Adjustments - JVC TV-13142 Service Manual

Hide thumbs Also See for TV-13142:
Table of Contents

Advertisement

TV-13142
TV-13142W
1. BEFORE MAKING ELECTRICAL
ADJUSTMENTS
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
CAUTION
•
Use an isolation transformer when performing any
service on this chassis.
•
Before removing the anode cap, discharge electricity
because it contains high voltage.
•
When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
Inferior silicon grease can damage IC's and transistors.
•
When replacing IC's and transistors, use only specified
silicon grease (YG6260M).
Remove all old silicon before applying new silicon.
On-Screen Display Adjustment
1.
Unplug the AC plug for more than 5 seconds to set the
clock to the non-setting state. Then, set the volume
level to minimum.
2.
Press the VOL. DOWN button on the set and the
Channel button (9) on the remote control simultaneously
to appear the adjustment mode on the screen as shown
in Fig. 1-1.
00 OSD
3.
Use the Channel UP/DOWN button or Channel button
(0-9) on the remote control to select the options shown
in Fig. 1-2.
4.
Press the MENU button on the remote control to end
the adjustments.
NO.
FUNCTION
00
OSD H
01
CUT OFF
02
RF DELAY
03
VIF VCO
04
H VCO
05
H PHASE
06
V SIZE
07
V SHIFT
08
R DRIVE
09
B DRIVE
10
R CUT OFF
11
G CUT OFF
12
B CUT OFF

ELECTRICAL ADJUSTMENTS

TV
15
Fig. 1-1
NO.
FUNCTION
13
BRIGHTNESS
14
CONTRAST
15
COLOR
16
TINT
17
SHARPNESS
18
FM LEVEL
19
LEVEL
20
SEPARATION 1
21
SEPARATION 2
22
TEST MONO
23
TEST STEREO
24
X-RAY TEST
Fig. 1-2

2. BASIC ADJUSTMENTS

(VCR SECTION)
2-1: PG SHIFTER
1.
Connect CH-1 on the oscilloscope to TP1002 and CH-2
to pin 4 of CP1003.
2.
Playback the alignment tape.
3.
Press and hold the Tracking-Auto button on the remote
control more than 2 seconds to set tracking to center.
4.
Press the VOL. DOWN button on the set and the
channel button (3) on the remote control simultaneously
until the indicator REC disappears. If the indicator REC
disappears, adjustment is completed.
(If the above adjustments doesn't work well:)
5.
Press the VOL. DOWN button on the set and the
channel button (3) on the remote control simultaneously
until the indicator REC disappears.
6.
When the REC indicator is blinking, press both VOL.
DOWN button on the set and the channel button (4) on
the remote control simultaneously and adjust the
Tracking +/- button until the arising to the down of Head
Switching Pulse becomes 6.5 ± 0.5H.
(Refer to Fig. 2-1-A, B)
7.
Press the Tracking Auto button.
6.5H
6.5H
2-2: VCO FREERUN
1.
Receive the VHF HIGH.
2.
Place the set with Aging Test for more than 10 minutes.
3.
Connect the digital voltmeter between the pin 5 of
CP351 and the pin 1 (GND) of CP351.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (03) on the remote control to
select "VIF VCO".
5.
Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 2.5V.
6.
After the 2.5V adjustment, countdown the VIF VCO step
No. by 1 step with the VOL. DOWN button.
CH-2
CH-1
Fig. 2-1-A
CH-2
CH-1
Fig. 2-1-B
Show Quick Links

Hide quick links:

Advertisement

Table of Contents
loading

Related Manuals for JVC TV-13142

Related Content for JVC TV-13142

This manual is also suitable for:

Tv-13142w

Table of Contents