Sony VPL-CX85 Operating Instructions Manual
Air shot
Hide thumbs
Also See for VPL-CX85:
- Operating instructions manual (192 pages) ,
- Service manual (116 pages) ,
- Operation instructions manual (21 pages)
Related Manuals for Sony VPL-CX85
Summary of Contents for Sony VPL-CX85
- Page 1 3-000-000-11 (1) Data Projector Operating Instructions for Air Shot VPL-CX85 © 2004 Sony Corporation...
- Page 2 Precautions xxxxxxx...
-
Page 3: Table Of Contents
Table of Contents Features ..........4 System Requirement ......5 Inserting Card ........5 Installation .......... 6 Connecting Examples ......7 When Simple Mode is Used ....8 When Simple Mode is not Used ..10 Setting/Operating the Projector from the Computer (via Web) ....12 Accessing from the Computer ..12 Confirming the State of Projector Settings (Information) ..13... -
Page 4: Features
Control by using Web browser Features You can control the projector and confirm its setting. This unit is equipped with the Air Shot (wireless connection) function. Any image Connection to a LAN of a computer can be projected by using the You can not only connect the projector and projector without connecting cables. -
Page 5: System Requirement
System Requirement Inserting Card Recommended system requirements for the Insert the supplied wireless LAN card into installed Projector Station for Air Shot are as the slot of the projector. follows. Inserting the card Available computer Insert the card facing the right side towards CPU: Intel Pentium III 600 MHz or higher the front panel of the projector until it stops. -
Page 6: Installation
Remove the card. Installation For using Air Shot, install the application software, Projector Station for Air Shot, in the computer. Connect the supplied USB storage media to the USB terminal of the computer. Note After the card is removed, press the eject Computer button. -
Page 7: Connecting Examples
Connecting to wireless LAN using Connecting the wireless LAN access point Examples For setting and operations, see “When Simple Mode is not Used” on page 10. Wireless LAN module Connecting one projector and one (supplied) computer Projector When Simple Mode is used See “When Simple Mode is Used”... -
Page 8: When Simple Mode Is Used
Connecting to several projectors at When Simple Mode the same time For setting and operations, see “When is Used Simple Mode is not Used” on page 10. Wireless LAN card Projector (supplied) Setting the projector Insert the supplied wireless LAN card into the slot of the projector. - Page 9 Click the [Change Projector] button of Setting the computer [Simple Mode Setting]. The dialog box with a projector name Start the Projector Station for Air and serial number is displayed. Shot. When it starts, the [ ] icon appears in Click the [Add] button and enter the the task bar.
-
Page 10: When Simple Mode Is Not Used
• Wireless Access Point: for wireless When Simple Mode LAN connection with the access point Network Name (SSID): enter the same is not Used network name as that of the connected computer. A maximum of 32 characters/numbers can be entered. Setting the projector Network Channel: when [Ad-hoc (Peer- to-peer)] is selected in [Network Mode],... - Page 11 IP Address: select the IP address setting wireless LAN module. from among 0 to 255. When a device other than the supplied wireless LAN module is used, set the Subnet Mask: select the subnet mask wireless setting of the computer so setting from among 0 to 255.
-
Page 12: Setting/Operating The Projector From The Computer (Via Web)
After access, the following display appears. Setting/Operating the Projector from the Computer (via Web) You can check the information of the projector from the computer or operate the projector on the computer. Check the connection and turn on the equipment. Accessing from the Computer You can access the Web page of the... -
Page 13: Confirming The State Of Projector Settings (Information)
Confirming the State of Setting the Connecting Mode Projector Settings (Simple Mode) (Information) Click [Simple Mode]. Set the Simple Mode and user name. Click [Information]. Click the [Apply] button to reflect the You can confirm the current state of the projector. -
Page 14: Operating The Projector On The Computer (Control)
Operating the Projector on Setting (Setup) the Computer (Control) Click [Setup]. Set for using the network function. Click [Control]. Click [Projector Setting] or [Password] and You can control the projector on the set each item. computer. The current state is reflected in the projector The keys that have the same names as those by clicking the [Apply] button. - Page 15 Simple Mode: set [On] or [Off]. User Memory: select from [User 1] to When [Off] is selected, set the [User 5]. Edit: click when you want to enter a new following. Setting: select [Ad-hoc (peer-to-peer)] or user name. The [User Name], [Setting] [Wireless Access Point].
-
Page 16: Troubleshooting
Troubleshooting Symptom Cause and Remedy The image does not • The supplied wireless LAN card is not used. c When the supplied wireless LAN card is not used, Air Shot does appear in Simple Mode. not work correctly. • A black screen appears (picture muting.) c Press the PIC MUTING key to release the muting. -
Page 17: Warning Messages
Warning Messages Symptom Cause and Remedy Cannot connect. • Cannot disconnect. • Cannot switch. • Wireless LAN card not • The wireless LAN card is not inserted correctly into the slot of the inserted. projector. c Check the card direction and insert until it stops. Incompatible card •... -
Page 18: Technical Terms
Access point mode Technical Terms The mode using the wireless access point in a wireless LAN. Air Shot Ad-hoc (peer-to -peer) mode The function to connect the computer and The mode not using the wireless access point the projector in wireless mode. in a wireless LAN. - Page 19 Sony Corporation...