Page 1
STR-D760Z/DE815G SERVICE MANUAL US Model STR-D760Z/DE815G Canadian Model E Model Australian Model PX Model STR-DE815G Photo : STR-DE815G SPECIFICATIONS — Continued on next page — FM STEREO FM-AM RECEIVER MICROFILM — 1 —...
DE815G : Canadian model 4-989-884-1 FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS DE815G : E, PX model 4-989-884-2 QUE PAR DES PIÈCES SONY DONT LES NUMÉROS DE815G : Singapore, Malaysia model 4-989-884-3 SONT DONNÉS DANS CE MANUEL OU DANS LES 4-989-884-4 DE815G : Australian model SUPPLÉMENTS PUBLIÉS PAR SONY.
SECTION 1 SERVICING NOTE ALL CLEAR Adjustment of OSD Screen Position Mode which erases all the user memories registered in this unit and The position of the screen can be adjusted freely to correct the de- sets to setting at shipment. viation of the OSD screen caused by the monitor type that users are using.
SECTION 4 ELECTRICAL ADJUSTMENT TUNER SECTION OSD Color burst Adjustment Procedure 2: (When no vectorscope is used) Connection: Connection: No adjustment is needed due to a tuner unit (TU401). frequency counter monitor screen Green area OSD SECTION VTR etc. Monitor S.VIDEO board OSD Width Adjustment JW232...
STR-D760Z/DE815G 5-2. BLOCK DIAGRAMS — DOLBY SURROUND SECTION — AUDIO SELECTOR IC406 FRONT REAR REAR 5.1 INPUT REAR L OUT R OUT CENTER CENTER C OUT CENTER CENTER MUTE FM/AM TUNER Q403 TU401 ANTENNA MUTE STEREO STEREO Q451 PANEL SECTION...
Page 28
STR-D760Z/DE815G — OSD SECTION — VIDEO SELECTOR IC211 BUFFER J211 VIDEO1 VIDEO OUT Q215,218 LD/DVD VIDEO IN TV/DBS VIDEO IN BUFFER VIDEO2 VIDEO OUT Q216,219 VIDEO3 INPUT VIDEO J209 VIDEO2 VIDEO IN CLAMP OSD SWITCH ON SCREEN DISPLAY (OSD) Q203...
Page 29
STR-D760Z/DE815G — POWER AMP SECTION — RY602 L/R DRIVER IC501 J701 PHONES HEADPHONE H.P RY PROTECTOR RELAY DRIVE DRIVE Q508 Q601 TM501 RY501 POWER AMP PRE DRIVE Q504–507 POWER AMP PRE DRIVE FRONT SP/A RY Q554–557 A RELAY DRIVE Q546...
Page 30
STR-D760Z/DE815G — PANEL SECTION — DISPLAY DRIVER IC102 EXCEPT Singapore, Malaysia model DISPLAY CONTROL • S151 IC103 POWER FLUORESCENT INDICATOR TUBE FL CLEAR S POWER FL101 FL DATA S105–108 AD KEY IN 1 FL CLK FL LAT SDATA • S113–115...
• OSD Section IC202 uPD4053BC IC205 MB90095PF-186-BND YOUT ANALOG COUT SWITCH VOUT TO BLOCK AVCC VIDEO SERIAL FSCO S.DATA SIGNAL INPUT 4FSC VBLK S.CLK GENERATOR CONTROL CLOCK 21 TEST VOC0 NTSC/PAL OUTPUT VOC1 SIGNAL CONTROL HSYNC VOC2 GENERATOR VSYNC DISPLAY IC210 LA7217 MEMORY CONTROL...
5-12. IC PIN FUNCTIONS • IC103 Mode Controller (MB90673PF-G-216-BND) Pin No. Pin Name Function AC MUTE Mute signal output to Rear power amp D. LAT Latch output to Dolby surround processor T. LAT Latch output to Tone controller S. CLK Serial clock output to Dolby surround processor S.
Page 45
Pin No. Pin Name Function MODE 0 Mode setting pin (Fixed at “H”) MODE 1 Mode setting pin (Fixed at “H”) MODE 2 Mode setting pin (Fixed at “L”) STANDBY Standby signal input of hardware STOP STOP signal input LEANING LED DE815G: LEARNING LED drive signal output D760Z: Not used —...
Page 46
• IC205 OSD (MB90095PF-G-186-BND) Pin No. Pin Name Function Luminous signal input for superimpose displays (Not used) Chroma signal input for superimpose displays (Not used) Composite signal input for superimpose displays AVCC – Power supply (+5V) (Analog) FSCO Color burst phase signal output VBLK Vertical blanking period output (Not used) –...
Page 47
• IC209 OSD Controller (MB90672PF-G-125-BND) Pin No. Pin Name Function 1, 2 AD14, AD15 Address bus and data bus input/output 3 to 6 A16 to A19 Address bus output Chip Enable output to RC controller (For communication using personal computers) PCLK Clock output to RC controller (For communication using personal computers) Data output to RC controller (For communication using personal computers)
Page 48
Function Pin No. Pin Name Mode setting (Fixed at “H”) MODE 0 Mode setting (Fixed at “L”) MODE 1 Mode setting (Fixed at “L”) MODE 2 Hardware standby (Fixed at “H”) HSTX Request input of reset interrupt STOP IR sensor remote control input (Not used) IR-IN (A6) Not used —...
Page 49
• IC215 RC Controller (LC86F5864A-5E72) Pin No. Function Pin Name P70/INT0 Chip enable input from OSD controller P71/INT1 Chip enable input (For on–board) (Not used) P72/INT 2/TOIN Not used (Connector to ground) P73/INT 3/TOIN SIRCS signal input Power supply normality signal input Infrared rays transmission data status signal output to OSD controller “L”...
Page 50
Pin No. Pin Name Function P10/SOO Serial data output to OSD controller P11/SI0/SB0 Serial data input to OSD controller P12/SCKO Serial clock input from OSD controller P13/SO1 – Ground P14/SI1 Serial data input (For on–board) (Not used) P15/SCK1 Serial clock input (For on–board) (Not used) P16/BUZ Not used P17/PWM...
SECTION 6 EXPLODED VIEWS NOTE: The components identified by • Abbreviation • Items marked “*” are not stocked since they are mark ! or dotted line with mark CND : Canadian model seldom required for routine service. Some delay ! are critical for safety. : Singapore model should be anticipated when ordering these items.
SECTION 7 5.1 IN ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by In each case, u: µ , for example: may be different from the parts specified in the mark ! or dotted line with mark uA...: µ...
SP SW STAND BY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R744 1-249-425-11 CARBON 4.7K 1/4W F A-4398-127-A STAND BY BOARD, COMPLETE (US,CND) (DE815G) ********************************** A-4398-138-A STAND BY BOARD, COMPLETE (E,PX) R745 1-249-421-11 CARBON 2.2K 1/4W F (DE815G) ********************************...