Pioneer DVH-P500UB Installation Manual
Dvd rds receiver
Hide thumbs
Also See for DVH-P500UB:
- Operation manual (96 pages) ,
- Service manual (125 pages) ,
- Service manual (125 pages)
Table of Contents
Advertisement
Quick Links
DVH-P500UB
Printed in Thailand
ç‡Ô˜‡Ú‡ÌÓ ‚ í‡Ë·̉Â
<CRD4326-A/N> RE
<KMMNX> <07L00000>
Connecting the Units
Note:
•
Control signal is output through blue/white cable
•
When this unit is installed in a vehicle without
when this unit is powered on. Connect it to an
ACC (accessory) position on the ignition switch,
external power amp's system remote control or
red cable must be wired to the terminal that can
the vehicle's auto-antenna relay control terminal
detect the operation of the ignition key.
(max. 300 mA, 12 V DC). If the vehicle is
Otherwise, battery drain may result.
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
•
Never connect blue/white cable to external power
amp's power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
•
IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
•
Black cable is ground. This cable and other prod-
ACC position
No ACC position
uct's ground cable (especially, high-current prod-
•
Use this unit in other than the following condi-
ucts such as power amp) must be wired separate-
tions could result in fire or malfunction.
ly. Otherwise, fire or malfunction may result if
— Vehicles with a 12-volt battery and negative
they are accidentally detached.
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
•
To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the battery
before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not remove RCA caps if RCA cables are
not used.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's nega-
tive cables.
Power cable connection
Note:
Depending on the kind of vehicle, the
function of 3* and 5* may be different. In
this case, be sure to connect 2* to 5* and 4*
Antenna jack
to 3*.
1*
15 cm
3*
2*
5*
4*
Connect leads of the same
color to each other.
Cap (1*)
Do not remove cap if
Fuse (10 A)
this terminal is not in
use.
Yellow (3*)
Yellow (2*)
Back-up (or
Connect to the constant
accessory)
12 V supply terminal.
Fuse resistor
Red (5*)
Red (4*)
Accessory
Connect to terminal controlled
(or back-up)
by ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Speaker leads
Note:
White:
Front left
In some vehicles, the ISO connector
White/black: Front left
may be divided into two. In this case,
Gray:
Front right
be sure to connect to both connectors.
Gray/black: Front right
Green:
Rear left
or subwoofer
When you connect the separately sold multi-channel
Green/black: Rear left
or subwoofer
processor (DEQ-P6600) to this unit, do not connect
Violet:
Rear right
or subwoofer
anything to the speaker leads and system remote
Violet/black: Rear right
or subwoofer
control (blue/white).
<ENGLISH>
AUX jack (3.5 ø)
20 cm
Use a mini plug cable
1.5 m
to connect with
auxiliary device.
USB cable
Connect to separately sold USB device.
15 cm
IP-BUS input
This product
(Blue)
Hard-wired remote control adaptor can be
connected (sold separately).
IP-BUS cable
Multi-CD player
(sold separately)
Yellow/black
If you use an equipment with Mute function, wire
this lead to the Audio Mute lead on that equipment.
If not, keep the Audio Mute lead free of any
connections.
Violet/white
Of the two lead wires connected to the back lamp,
connect the one in which the voltage changes when
the gear shift is in the REVERSE (R) position.
For details, refer to When connecting with a rear
view camera.
Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Blue/white (7*)
Blue/white (6*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
Notes:
The pin position of the ISO connector will differ
• Change the initial setting of this unit (refer to the
depends on the type of vehicle. Connect 6* and
Operation Manual). The subwoofer output of this
7* when Pin 5 is an antenna control type. In
unit is monaural.
another type of vehicle, never connect 6* and 7*.
• When using a subwoofer of 70 W (2 Ω) , be sure to
connect with Violet and Violet/black leads of this
unit. Do not connect anything with Green and
Green/black leads.
Advertisement
Table of Contents
Related Manuals for Pioneer DVH-P500UB
Summary of Contents for Pioneer DVH-P500UB
- Page 1 Black cable is ground. This cable and other prod- ACC position No ACC position connected (sold separately). IP-BUS cable DVH-P500UB uct’s ground cable (especially, high-current prod- • Use this unit in other than the following condi- Connect leads of the same...
-
Page 2: Connecting The Units
Connecting the Units Connecting the Units <ENGLISH> <ENGLISH> Connecting and installing the Installing the optical cable Connecting to separately sold power amp When connecting with a multi-channel processor optical cable connection box connection box Power amp (sold • When installing the optical cable WARNING separately) •... -
Page 3: When Using A Display Connected Video Outputs
Connecting the Units <ENGLISH> When using a display connected video outputs When connecting with a rear view camera When this product is used with a rear view camera, it is possible to automatically switch WARNING from the video to rear view image when the gear shift is moved to REVERSE (R). NEVER install the display in a location that enables the Driver to watch the DVD or Video CD WARNING while Driving. -
Page 4: Installation
Installation <ENGLISH> Note: • The cords must not cover up the area shown in the DIN Front/Rear-mount Removing the Unit DIN Rear-mount Fastening the front panel figure below. This is necessary to allow the • Check all connections and systems before final 1. -
Page 5: Èó‰Íî˛˜âìëâ ÛòúÓèòú
èÓ‰Íβ˜ÂÌË ÛÒÚÓÈÒÚ‚ <êìëëäàâ> èËϘ‡ÌËÂ: • äÓÌÚÓθÌ˚È Ò˄̇Π‚˚ıÓ‰ËÚ ÔÓ ÒËÌÂ/·ÂÎÓÏÛ ëÓ‰ËÌÂÌËfl ÒËÎÓ‚˚ı ͇·ÂÎÂÈ • äÓ„‰‡ ‰‡ÌÌÓ ÛÒÚÓÈÒÚ‚Ó ÛÒڇ̇‚ÎË‚‡ÂÚÒfl ‚ ͇·Âβ, ÍÓ„‰‡ ‰‡ÌÌÓ ÛÒÚÓÈÒÚ‚Ó ÔÓ‰Íβ˜ÂÌÓ Í Ú‡ÌÒÔÓÚÌÓÏ Ò‰ÒÚ‚Â ·ÂÁ ACC ˝ÎÂÍÚÓÔËÚ‡Ì˲. èÓ‰Íβ˜ËÚÂ Â„Ó Í ÒËÒÚÂÏ ÉÌÂÁ‰Ó AUX (3.5 ø) (‚ÒÔÓÏÓ„‡ÚÂθÌ˚ ÔË·Ó˚) ÔÓÎÓÊÂÌËfl ̇ Á‡ÏÍ ‰ËÒڇ̈ËÓÌÌÓ„Ó... - Page 6 èÓ‰Íβ˜ÂÌË ÛÒÚÓÈÒÚ‚ Connecting the Units <êìëëäàâ> <ENGLISH> ëÓ‰ËÌÂÌËÂ Ò ÛÒËÎËÚÂÎÂÏ ÏÓ˘ÌÓÒÚË, ÍÓÚÓ˚È ÔÓ‰‡ÂÚÒfl ÓÚ‰ÂθÌÓ èÓ‰Íβ˜ÂÌË ÏÌÓ„Ó͇̇θÌÓ„Ó ÔÓˆÂÒÒÓ‡ èÓ‰ÒÓ‰ËÌÂÌËÂ Ë ÏÓÌÚ‡Ê 2. èÓ‰ÒÓ‰ËÌËÚ ÓÔÚ˘ÂÒÍËÈ Í‡·Âθ Í ÒÓ‰ËÌËÚÂθÌÓÈ ÍÓÓ·Í ÒÓ‰ËÌËÚÂθÌÓÈ ÍÓÓ·ÍË ÓÔÚ˘ÂÒÍÓ„Ó Í‡·ÂÎfl. ÓÔÚ˘ÂÒÍÓ„Ó Í‡·ÂÎfl ìÒËÎËÚÂθ ÏÓ˘ÌÓÒÚË (ÔÓ‰‡ÂÚÒfl ÓÚ‰ÂθÌÓ) ÇçàåÄçàÖ ä‡Ï‡ Á‡‰ÌÂ„Ó ‚ˉ‡ ëÓ‰ËÌËÚÂ...
- Page 7 èÓ‰Íβ˜ÂÌË ÛÒÚÓÈÒÚ‚ <êìëëäàâ> äÓ„‰‡ ËÒÔÓθÁÛÂÚÒfl ˝Í‡Ì, ÔÓ‰Íβ˜ÂÌÌ˚È Í ‚ˉÂÓ‚˚ıÓ‰‡Ï äÓ„‰‡ ÔÓ‰Íβ˜‡ÂÚÂÒ¸ ‚ ͇Ï Á‡‰ÌÂ„Ó ‚ˉ‡ äÓ„‰‡ ‰‡ÌÌÓ ÛÒÚÓÈÒÚ‚Ó ËÒÔÓθÁÛÂÚÒfl Ò Í‡ÏÂÓÈ Á‡‰ÌÂ„Ó Ó·ÁÓ‡, ÏÓÊÌÓ èêÖÑìèêÖÜÑÖçàÖ ‡‚ÚÓχÚ˘ÂÒÍË ÔÂÂÍβ˜ËÚ¸ ÓÚ ‚ˉÂÓ Í ËÁÓ·‡ÊÂÌ˲ Á‡‰ÌÂ„Ó Ó·ÁÓ‡, ÍÓ„‰‡ ˚˜‡„ çËÍÓ„‰‡ Ì ÛÒڇ̇‚ÎË‚‡ÈÚ ˝Í‡Ì ‚ ÏÂÒÚÂ, ÍÓÚÓÓ ‰‡ÒÚ ‚ÓÁÏÓÊÌÓÒÚ¸ ‚Ó‰ËÚÂβ ÒÏÓÚÂÚ¸ ÔÂÂÍβ˜ÂÌËfl...
- Page 8 ìÒÚ‡Ìӂ͇ <êìëëäàâ> èËϘ‡ÌËÂ: • 䇷ÂÎË Ì ‰ÓÎÊÌ˚ Á‡Í˚‚‡Ú¸ Û˜‡ÒÚÓÍ, è‰ÌÂÂ/ᇉÌ ÍÂÔÎÂÌË 쉇ÎÂÌË ìÒÚÓÈÒÚ‚‡ ᇉÌ ÍÂÔÎÂÌË ÔÓ Òڇ̉‡ÚÛ DIN á‡ÍÂÔÎÂÌË Ô‰ÌÂÈ Ô‡ÌÂÎË • èӂ¸Ú ‚Ò ÒÓ‰ËÌÂÌËfl Ë ÒËÒÚÂÏ˚ Ô‰ Û͇Á‡ÌÌ˚È Ì‡ ÒÎÂ‰Û˛˘ÂÏ ËÒÛÌÍÂ. ùÚÓ ÔÓ Òڇ̉‡ÚÛ DIN 1. éÚÚflÌËÚ ‚Âı Ë ÌËÁ ·ÒÚ˘ÌÓ„Ó Ó·Ó‰Í‡ Ú·ӂ‡ÌËÂ...