GE GFDS150EDWW Installation Instructions Manual
Ge 7.5 cu. ft. capacity frontload dryer with steam and stainless steel drum
Hide thumbs
Also See for GFDS150EDWW:
- Owner's manual (60 pages) ,
- Installation instructions manual (17 pages)
Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Download this manual
See also:
Owner's Manual
Installation
Instructions
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
• IMPORTANT-
Save these instructions
for local inspector's use.
• IMPORTANT-
Observe all governing
codes and ordinances.
• Note to Installer -
instructions with the customer.
• Note to Customer - Keep these instructions
with your Owner's Manual for future
reference.
•
or discarded, remove the dryer door.
• Service information and the wiring diagram
are located in the control console.
• Do not allow children on or in the appliance.
Close supervision of children isnecessary
when the appliance is used near children.
• Install the dryer where the temperature is
dryer control system.
• Product failure due to improper installation
is not covered under the Warranty.
TOOLS YOU
WILL NEED
SLIP JOINT PLIERS
FLAT BLADE SCREWDRIVER
PHILLIPS SCREWDRIVER
LEVEL
Minimum Clearance Other Than Alcove or Closet Installation
Consideration must be given to provide adequate clearance for installation and service.
Printed in Mexico
Questions on Installation? Call: 800.GE.CARES (US)
or visit our Web site at: www.GEAppliances.com (US)
• To reduce the risk of severe injury or death, follow all installation
instructions.
•
• Install the clothes dryer according to these instructions and in accordance
with local codes.
• This dryer must be exhausted to the outdoors.
• Use only rigid metal 4" diameter ductwork inside the dryer cabinet and use
only UL approved transition ducting between the dryer and the home duct.
•
and installed in accordance with the instructions found in "Connecting
materials are known to collapse, be easily crushed, and trap lint. These
• Do not install or store this appliance in any location where it could be
exposed to water and or weather.
•
NOTE: Installation and service of this dryer requires basic
mechanical and electrical skills. It is your responsibility to contact
MATERIALS YOU WILL NEED
4" DIA. METAL DUCT
(RECOMMENDED)
4" DIA. FLEXIBLE METAL (SEMI-RIGID)
UL LISTED TRANSITION DUCT
(IF NEEDED)
KIT WX08X10077 (INCLUDES 2 ELBOWS)
4" DIA. FLEXIBLE METAL (FOIL TYPE)
UL LISTED TRANSITION DUCT
(IF NEEDED.)
WARNING
RISK OF FIRE
4" DUCT
4" DIA. METAL
CLAMPS (2)
ELBOW
OR
4" SPRING
CLAMPS (2)
DUCT TAPE
4" COVER PLATE (IF NEEDED
(KIT WE1M454)
Electric Dryer
01
SAFETY
EXHAUST
GLASSES
HOOD
3/4" STRAIN
RELIEF
GLOVES
UL RECOGNIZED
234D2008P001 31-16714 03-13 GE
DRYER POWER
CORD KIT
(NOT PROVIDED
WITH DRYER)
UL RATED
120/240V,30A
WITH 3 OR 4 PRONGS.
IDENTIFY THE PLUG
TYPE AS PER THE
HOUSE RECEPTACLE
BEFORE PURCHASING
LINE CORD.
Advertisement
Table of Contents
Related Manuals for GE GFDS150EDWW
Summary of Contents for GE GFDS150EDWW
-
Page 1: Electric Dryer
Installation Electric Dryer Instructions Questions on Installation? Call: 800.GE.CARES (US) or visit our Web site at: www.GEAppliances.com (US) BEFORE YOU BEGIN WARNING RISK OF FIRE Read these instructions completely and • To reduce the risk of severe injury or death, follow all installation carefully. -
Page 2: Installation Instructions
Installation Instructions CONNECTING DRYER USING 4-WIRE PREPARING FOR INSTALLATION OF CONNECTION (MUST BE USED FOR NEW DRYER MOBILE HOME INSTALLATION) TIP: Install your dryer before installing your washer. This will allow better access when installing dryer exhaust. NOTE: Since January 1,1996, the National Electric code requires REMOVING LINT FROM WALL EXHAUST that the new constructions utilize a 4-wire connection to an electric dryer. - Page 3 Installation Instructions CONNECTING DRYER USING 3-WIRE CONNECTION 3-wire Connection to grounded metal, cold water pipe, or other established ground Not for use in Canada. determined by a qualified electrician. DO NOT use for Mobile Home Installations. Wire according to the terminal block illustration that matches NOT for use on new construction.
-
Page 4: Exhaust Information
Installation Instructions EXHAUST INFORMATION EXHAUST LENGTH WARNING - IN CANADA AND IN THE RECOMMENDED MAXIMUM LENGTH UNITED STATES, THE REQUIRED EXHAUST DUCT Exhaust Hood Types DIAMETER IS 4 in (102mm). DO NOT USE DUCT Use only for short Recommended LONGER THAN SPECIFIED IN THE EXHAUST run installations 4"... -
Page 5: Exhaust Connection
Installation Instructions STANDARD REAR EXHAUST EXHAUST SYSTEM CHECK LIST (cont.) SEPARATION OF TURNS For straight line installation, connect straight duct, including distance between last turn and exhaust the dryer exhaust to the external hood. exhaust hood using duct tape or clamp. -
Page 6: Alcove Or Closet Installation
Installation Instructions For best drying performance pipe. 2. Secure the duct with a clamp. without kinking and or crushing the transition duct, to its full length. Allow 2” of duct to overlap the exhaust • Avoid resting the duct on sharp objects. UL-LISTED FLEXIBLE METAL (FOIL-TYPE) TRANSITION DUCT 4. - Page 7 Installation Instructions BATHROOM OR BEDROOM INSTALLATION FIXING HOLE • The installation must conform with local codes or, in the absence of local codes, with the NATIONAL ELECTRICAL 9" Cut the duct as shown and keep portion A. TAB LOCATION MOBILE OR MANUFACTURED HOME INSTALLATION BEND TAB UP 45...
- Page 8 Installation Instructions ADDING ELBOW AND DUCT FOR ADDING COVER PLATE TO REAR OF EXHAUST TO LEFT OR RIGHT SIDE OF CABINET (SIDES AND BOTTOM EXHAUST) CABINET • Preassemble 4” elbow with 4” duct. Wrap duct tape around joint. opening and connect the elbow to the dryer internal duct.
-
Page 9: Instrucciones De Instalación
(SI ES NECESARIO Espacio mínimo diferente a instalación en nichos o closets frente y 3 pulg. en la parte trasera. Debe tenerse en cuenta un espacio libre adecuado para un funcionamiento y reparación correctos. 234D2008P001 31-16714 03-13 GE Impreso en México... -
Page 10: Requisitos Eléctricos
Instrucciones de instalación CÓMO CONECTAR LA SECADORA USANDO PREPARACIÓN PARA LA INSTALACIÓN UNA CONEXIÓN DE 4 CABLES (DEBE UTILIZARSE DE UNA SECADORA NUEVA EN INSTALACIONES DE CASAS MÓVILES) CONSEJO: Instale su secadora antes de instalar la lavadora. Esto permitirá un mejor acceso cuando NOTA: Desde el 1 de enero de 1996, el Código Eléctrico Nacional instale la salida de la secadora. - Page 11 Instrucciones de instalación CÓMO CONECTAR LA SECADORA UTILIZANDO UNA CONEXIÓN DE 3 CABLES NO usar en Canadá. agua fría con conexión a tierra u otra conexión a tierra establecida NO usar en instalaciones en casas móviles. por un electricista calificado. NO usar en casas nuevas.
- Page 12 Instrucciones de instalación INFORMACIÓN DE SALIDA ADVERTENCIA LONGITUD DE SALIDA – EN CANADÁ Y LONGITUD MÁXIMA RECOMENDADA LOS ESTADOS UNIDOS, EL DIÁMETRO Tipos de campana de salida Utilizar sólo en instalaciones DE CONDUCTO DE SALIDA REQUERIDO Recomendado de trayecto corto 4"...
- Page 13 Instrucciones de instalación LISTA DE CONTROL DEL SISTEMA DE SALIDA riesgo potencial de incendio. (cont.) un riesgo potencial de incendio. SEPARACIÓN DE CURVAS incendio. menos 4 pies de conducto recto, incluyendo la distancia entre la • Incluya un acceso para inspección y limpieza del sistema GIROS QUE NO SON DE 90°...
- Page 14 Instrucciones de instalación NOTA: LOS CODOS EVITAN QUE LOS cielorrasos, pisos u otros espacios cerrados. CONDUCTOS SE DOBLEN O CAIGAN. CÓMO CONECTAR LA SECADORA A LA VENTILACIÓN DOMÉSTICA CONDUCTO DE TRANSICIÓN DE METAL RÍGIDO QUÉ NO HACER conducto de transición de metal rígido. •...
- Page 15 Instrucciones de instalación SALIDA DE LA SECADORA HACIA LA INSTALACIÓN EN NICHO O EN CLOSET DERECHA, IZQUIERDA O PARTE INFERIOR DEL GABINETE aparato. • Esta secadora DEBE tener una ventilación al exterior. ADVERTENCIA - Ver la INFORMACIÓN SOBRE SALIDA secciones 3 y 4. ANTES DE •...
- Page 16 Instrucciones de instalación CÓMO AGREGAR CONDUCTOS NUEVOS CÓMO AGREGAR UN CODO DE SALIDA A ORIFICIO TRAVÉS DE LA PARTE INFERIOR DEL GABINETE DE MONTAJE • Introduzca el codo a través de la abertura trasera y PORCIÓN “A” conéctelo al conducto interno de la secadora. interno de la secadora y el codo, como puede verse SALIDA LATERAL POR DERECHA O IZQUIERDA...