PLC-HF15000L Expand Serial Command Functional Specifications Overview 1ÿ 0û This Functional Specification defines communication for PLC-HF15000L. 0û Most commands are also available to remote-control a projector through RS-232C from a computer. Therefore, commands are defined as Expand Serial Commands. 0û The operation by some commands depends on Optional Board installed in Input Slot of the projector.
Page 11
PLC-HF15000L Expand Serial Command Functional Specifications 0û Expand Serial Command is defined as a single command per line that starts with “C” and ends with carriage return (0x0D). 0û When a projector receives carriage return (0x0D), it starts decoding. 0û There are two types of commands as below: Example of Functional Execution Command:”CF_BRIGHT_032”...
PLC-HF15000L Expand Serial Command Functional Specifications Notation 4ÿ 0û Data from a controller to a projector is represented as COMMAND, and data from a projector to a controller in response to the incoming command is represented as RESPONSE. 0û [CR]: Carriage Return Code The command ends with carriage return code.
PLC-HF15000L Expand Serial Command Functional Specifications Functional Execution Command Table 5ÿ 5.1 Image Command Table Execute command Item CF_CONT_%1[CR] Set value of Contrast CF_BRIGHT_%1[CR] Set value of Brightness CF_COLOR_%1[CR] Set value of Color CF_TINT_%1[CR] Set value of Tint CF_COLMNSAV_%1[CR] Set area to store current values of Color Management CF_COLMNLD_%1[CR] Set area to load values of Color Management CF_APCTRL_%1[CR]...
PLC-HF15000L Expand Serial Command Functional Specifications 5.3 Input Control Command Table Execute command Item CF_INPUT_%1[CR] Select Input CF_SOURCE_%1[CR] Select Source of selected Input CF_INPUT1_%1[CR] Select Input1 and also set input source to %1 CF_INPUT2_%1[CR] Select Input2 and also set input source to %1 CF_INPUT3_%1[CR] Select Input3 and also set input source to %1 CF_INPUT4_%1[CR]...
Page 15
PLC-HF15000L Expand Serial Command Functional Specifications Select Input and Source of Sub picture for “Picture in CF_PIPSUBINP_%1_%2[CR] Picture” CF_PIPSIZE_&1[CR] Set size of Main /Sub picture for “Picture in Picture” CF_PIPSIZEMAIN_&1[CR] Set size of Main picture for “Picture in Picture” CF_PIPSIZESUB_&1[CR] Set size of Sub picture for “Picture in Picture”...
PLC-HF15000L Expand Serial Command Functional Specifications CF_PTIME_%1[CR] Set the time for count down mode in P-timer function CF_KEYDIS_%1[CR] Set limitation of RC/KEY control CF_FDEFAULT_%1[CR] Return the settings to Factory Default status CF_SHUTRCPROT_%1[CR] Set valid / invalid of RC use on Shutter control function Set valid / invalid use of key on the side panel on CF_SHUTKEYPROT_%1[CR] Shutter control function...
PLC-HF15000L Expand Serial Command Functional Specifications Status Read Command Table 6ÿ 6.1 Image Status Read Command Table Status read command Item CR_CONT [CR] Get value of Contrast CR_BRIGHT [CR] Get value of Brightness CR_COLOR [CR] Get value of Color CR_TINT [CR] Get value of Tint CR_APCTRL Get setting status of Auto Picture Control...
PLC-HF15000L Expand Serial Command Functional Specifications CR_SRCINP1 [CR] Get selected source for Input 1 CR_SRCINP2 [CR] Get selected source for Input 2 CR_SRCINP3 [CR] Get selected source for Input 3 CR_SRCINP4 [CR] Get selected source for Input 4 CR_HMSLOT [CR] Get the total number of Slots CR_NMSLOT1 [CR] Get a card name inserted to Slot 1...
PLC-HF15000L Expand Serial Command Functional Specifications 6.7 Setting Status Read Command Table Status read command Item CR_LANG [CR] Get selected language CR_MENUSIZE [CR] Get setting status of Menu size CR_DISP [CR] Get setting status of Display CR_BACKGND [CR] Get setting status of Screen for no signal CR_LOGO [CR] Get setting status of Logo CR_LOGOLOCK [CR]...
PLC-HF15000L Expand Serial Command Functional Specifications CR_BLENDBLK[CR] Get setting status of Black level of Edge blending CR_BLENDTESTPAT[CR] Get setting status of Test pattern of Edge blending CR_COLORMATCHING[CR] Get setting status of Color matching CR_CMMSXY_%1[CR] Get “x”,”y” value of Measured of Color matching CR_CMMSL_%1[CR] Get “L”...
PLC-HF15000L Expand Serial Command Functional Specifications Functional Execution Command 8ÿ 8.1 Format 1) PC issues a command in the format below: Pattern1: “CF_Command” [CR] Pattern2: “CF_Command_” %1 [CR] CF_: Header Command: String %1: Parameter (String) _: Space (To separate Command and Parameter) 2) The projector decodes the received command and when it gets ready to receive another command, it returns the response.
PLC-HF15000L Expand Serial Command Functional Specifications 8.4 Image Command 8.4.1 CF_ CONT Command Command “CF_CONT_%1” [CR] “000-063”--------------- Directly specify setting value of Contrast “UP”--------------------- Increment setting value of Contrast by 1 “DN”--------------------- Decrement setting value of Contrast by 1 Set user controlled value of Contrast. (Available only in the normal Power ON status) Details The value set by this command is not stored in the projector.
PLC-HF15000L Expand Serial Command Functional Specifications 8.4.5 CF_COLMNSAV Command Command “CF_COLMNSAV_%1” [CR] “000 – 009” ---------------- Specify the area to store Store current setting status of Color Management to the area specified in %1. Details (Available only in the normal Power ON status) Acceptable “000”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.4.9 CF_WBAL- Command Command “CF_WBAL-%1_%2” [CR] “R” ------------- RED “G” ------------ GREEN “B” ------------- BLUE “000-063”------ Directly specify value of Color selected in %1 of White Balance. “UP”------ Increment setting value of Color specified in %1 of White Balance by 1 “DN”----- Decrement setting value of Color specified in %1 of White Balance by 1 Set value of Color specified in %1 of White Balance (Available only in the normal Power ON status)
PLC-HF15000L Expand Serial Command Functional Specifications 8.4.12 CF_GAMMA Command Command “CF_GAMMA_%1” [CR] “000-015” ---------------- Directly specify setting value of Gamma “UP”---------------------- Increment setting value of Gamma by 1 “DN”---------------------- Decrement setting value of Gamma by 1 Set user controlled value of Gamma. (Available only in the normal Power ON status) Details The value set by this command is not stored in the projector’s memory.
PLC-HF15000L Expand Serial Command Functional Specifications 8.4.15 CF_IMAGE Command Command “CF_IMAGE__%1” [CR] “STAND” ----------- Standard (Image adjustment value is set to factory default) “REAL” ------------- Real (Fixed value to display graphic image with natural tone) “CINEMA” --------- Cinema (Fixed value to focus on tone reproduction for movie) “DYNAMIC”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.4.17 CF_ADVCOL Command Command “CF_ADVCOL_%1” [CR] “AUTO” -------------- Set Advanced color to Auto “OFF” ----------------- Set Advanced color OFF. “UP” ----------- The same operation as pressing Up key or Left key “DN” -----------The same operation as pressing Down key or Right key *”UP”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.5 PC Control Command 8.5.1 CF_FSYNC Command Command “CF_FSYNC_%1” [CR] “0000-0031” ----------------- Directly specify setting value of Fine Sync “UP” --------------------------- Increment setting value of Fine Sync by 1 “DN” --------------------------- Decrement setting value of Fine Sync by 1 Set value of Fine Sync in PC signal (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory.
PLC-HF15000L Expand Serial Command Functional Specifications 8.5.4 CF_V-POS Command Command “CF_V-POS_%1” [CR] “0000-nnnn” ------------ Directly specify setting value of Vertical Position “nnnn” indicates maximum value, which is current (Total Line – Display Area V) value “UP” --------------------- Increment setting value of Vertical Position by 1 “DN”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.5.7 CF_DLINE Command Command “CF_DLINE_%1” [CR] “0100-nnnn” ----------- Directly specify setting value of Display Line “nnnn” indicates maximum value, which is current value of (Total Line - Position V). “UP” ------------------- Increment setting value of Display Line by 1 “DN”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.5.9 CF_PCSTORE Command Command “CF_PCSTORE_%1” [CR] “MODE1” --------------------------- Store current PC Adjust status to Mode1 “MODE2” --------------------------- Store current PC Adjust status to Mode2 “MODE3” --------------------------- Store current PC Adjust status to Mode3 “MODE4” --------------------------- Store current PC Adjust status to Mode4 “MODE5”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.7.3 CF_KEYSTONE Command Command “CF_KEYSTONE _%1” [CR] “UP” ------------- Correct Keystone distortion to reduce upper part of image “FUP” ----------- Correct Keystone distortion to reduce upper part “DN” ------------- Correct Keystone distortion to reduce lower part of image “FDN”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.7.6 CF_CORNER-DL Command Command “CF_CORNER-DL%1”[CR] “UP” ------------ Correct the horizontal line of image upwards “DN” ------------ Correct the horizontal line of image downwards “LEFT” --------- Correct the vertical line of image to the left “RIGHT”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.7.10 CF_CEIL Command Command “CF_CEIL_%1” [CR] “ON” --------------------------- Set Ceiling to ON “OFF” ------------------------- Set Ceiling to OFF Set/Cancel Ceiling. (Valid only when in the normal Power ON status.) When Ceiling is set to ON, image is left/right as well as top/bottom reversed. Details The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
PLC-HF15000L Expand Serial Command Functional Specifications 8.8 Lamp Command 8.8.1 CF_LAMPMODE Command Command “CF_LAMPMODE_%1” [CR] “4LAMP” ------------- Set lamp mode to 4-lamps “3LAMPAUTO” ---- Set lamp mode to 3-lamps and automatically and preferentially use lamps with shorter cumulated lighting time. “3LAMP123”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.8.4 CF_LAMPLIFECONTRL Command Command “CF_LAMPLIFECONTRL_%1” [CR] “MODE1” -------------------------- Set Lamp life control mode to Mode1 “MODE2” -------------------------- Set Lamp life control mode to Mode2 Select Lamp life control. (Valid only when in the normal Power ON status.) Details The value set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.4 CF_DISP Command Command “CF_DISP_%1” [CR] “ON” ----------------------------- Set Display to ON “CNTDWNOFF” -------------- Set Display to Count down Off “OFF” --------------------------- Set Display to OFF “UP” ----------- The same operation as pressing Up key or Left key “DN”...
PLC-HF15000L Expand Serial Command Functional Specifications Select input and source of Sub picture of “Picture in Picture”. (Valid only when in the normal Power ON status.) * In the case of a specific status, return Error Code “101” [CR] and the command is Details not executed.
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.13 CF_PIPPOSITION Command Command “CF_PIPPOSITION_%1” [CR] “POS1” -------------------- Move main picture position to up “POS2” -------------------- Move main picture position to down “POS3” -------------------- Move main picture position to left “POS4” -------------------- Move main picture position to right “POS5”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.16 CF_PIPMODEFREE Command Command “CF_PIPMODEFREE_%1” [CR] “USER1” --------------------------- Set User1 to Free status “USER 2” -------------------------- Set User2 to Free status “USER 3” -------------------------- Set User3 to Free status “USER 4” -------------------------- Set User4 to Free status “USER 5”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.20 CF_BLENDSTART Command Command “CF_BLENDSTART_%1_%2” [CR] “LEFT” ---------------------- Left side “RIGHT” -------------------- Right side “TOP” ----------------------- Upper side “BOTTOM” ---------------- Lower side “000”-“1024”-------------------- Directly specify value of direction of %1 *Value of upper limit changes by choice of %1 Left ---------------------- 000~1024 Right -------------------- 000~1024 Top ---------------------- 000~540...
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.23 CF_BLENDTESTPAT Command Command “CF_BLENDTESTPAT_%1” [CR] “ON” ---------------------- Set to On “OFF” -------------------- Set to Off Set Test pattern of Edge blending.(Available only in the normal Power ON status) Details The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.28 CF_CMMSXY Command Command “CF_CMMSXY_%1_%2_%3” [CR] “RED” ---------------------- Set value of Red “GREEN” ----------------- Set value of Green “BLUE” -------------------- Set value of Blue “0000” – “1000” --------- Directly specify “x” value of color of %1 “0000”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.31 CF_CMTGG Command Command “CF_CMTGG_%1_%2” [CR] “RED” ---------------------- Set value of Red “GREEN” ----------------- Set value of Green “BLUE” -------------------- Set value of Blue “WHITE” ------------------ Set value of White “CYAN” -------------------- Set value of Cyan “MAGENTA”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.35 CF_CMMSTESTPAT Command Command “CF_CMMSTESTPAT_%1” [CR] “RED” ---------------------- Display Red “GREEN” ------------------ Display Green “BLUE” -------------------- Display Blue “OFF” --------------------- Do not show test pattern display Display Test pattern of Measured of Color matching. Details (Available only in the normal Power ON status) Acceptable...
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.39 CF_CMMENU Command Command “CF_CMMENU_%1” [CR] “ON” ---------------------- Display Advanced color matching menu “OFF” --------------------- Set Advanced color matching menu undisplayed. Set Advanced color matching menu displayed or undisplayed. Details (Available only in the normal Power ON status) Acceptable “000”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.46 CF_P-MANE Command Command “CF_P-MANE_%1” [CR] “OFF” ---------------------------------- Set Power Management to Off “READY” ----------------------------- Set Power Management to Ready “SHUTDOWN” --------------------- Set Power Management to Shut Down mode “UP” ----------- The same operation as pressing Up key or Left key “DN”...
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.50 CF_PJPINCODE Command Command “CF_PJPINCODE_%1” [CR] “0000 – 9999” ------------- Directly specify PJ PIN code Enter PIN code to cancel PIN code lock (Available only in the normal Power ON status) PIN code can not be changed. (Only PIN code lock is canceled.) *When PIN code Lock is enabled: PIN code is matched ------------------------- Command is valid (Acceptable) PIN code is mismatched -------------------- Command is invalid (Error code “102”)
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.54 CF_SHUTEFFECT Command Command “CF_SHUTEFFECT_%1” [CR] “OFF” --------Disable fade in and out function of Shutter “L1” --------- Set fade in and out function of Shutter to L1 “L2” --------- Set fade in and out function of Shutter to L2 Set Effect function of Shutter.
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.58 CF_CCAPTIONCOLOR Command Command “CF_CCAPTIONCOLOR _%1” [CR] “COLOR” ------- Select Color “WHITE” -------- Select White Select color of Closed caption. The status set with this command is stored in EEPROM and its setting is effective even after ALL is OFF.
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.62 CF_ PTIMEMODE Command Command “CF_PTIMEMODE_%1” [CR] “COUNTUP” ---------------------- Set P-timer to Count up mode “COUNTDN” ---------------------- Set P-timer to Count down mode Select count up/down mode of P-timer. (Available only in the normal Power ON status) Details The status set by this command is stored in EEPROM and setting value remains effective even after the power is turned to ALL OFF status.
PLC-HF15000L Expand Serial Command Functional Specifications 8.9.66 CF_FDEFAULT Command Command “CF_FDEFAULT_%1” [CR] “RST” Return the settings to Factory Default status (Valid only when in the normal Power Details ON status) Acceptable “000” [CR] Response Unacceptable “Error Code” [CR] 61/105...
PLC-HF15000L Expand Serial Command Functional Specifications 8.10.3 CF_POWER Command Command “CF_POWER_%1” [CR] “ON” ----------------------------- Power ON “OFF” --------------------------- Power OFF * Issuing another command during countdown process forced countdown operation to be terminated. * Error Code is returned in some projector statuses, which indicates the command is impossible to be executed.
PLC-HF15000L Expand Serial Command Functional Specifications Status Read Command 9ÿ 9.1 Format PC issues a command in the format below: “CR_Command” [CR] Command: String When the projector receives the applicable command, it returns the required information as a data string. “000_”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.4 Image Status Read Commands 9.4.1 CR_CONT Command Command “CR_CONT” [CR] Details Get user controlled value of Contrast Acceptable “000_%1” [CR] Response “000” – “063” Unacceptable “?” [CR] 9.4.2 CR_BRIGHT Command Command “CR_BRIGHT” [CR] Details Get user controlled value of Brightness Acceptable...
PLC-HF15000L Expand Serial Command Functional Specifications 9.4.12 CR_OFFSET-B Command Command “CR_OFFSET-B” [CR] Details Get user controlled Blue value of Offset Acceptable “000_%1” [CR] Response “000” – “063” Unacceptable “?” [CR] 9.4.13 CR_SHARP Command Command “CR_SHARP” [CR] Details Get user controlled value of Sharpness Acceptable “000_%1”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.5 PC Status Read Commands 9.5.1 CR_FSYNC Command Command “CR_FSYNC” [CR] Details Get value of Fine Sync Acceptable “000_%1” [CR] Response “0000” – “0031” “Error Code” [CR] -------------- When command is invalid in the Unacceptable given condition (such as being selected input) “?”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.5.5 CR_CLAMP Command Command “CR_CLAMP” [CR] Details Get value of Clamp Acceptable “000_%1” [CR] “0000” – “ 4095” Response “Error Code” [CR] -------------- When command is invalid in the Unacceptable given condition (such as being selected input) “?”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.5.8 CR_ORGMODE Command Command “CR_ORGMODE” [CR] Get the original signal of current selected Mode that is set in PC Adj. Details When MODE1- 10 or EXT11-60 is not selected, get the current signal. Acceptable “000_%1”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.6 Video Status Read Command 9.6.1 CR_SERSYS Command Command “CR_SERSYS” [CR] Get currently selected signal. Details Value only when Input is video. (Invalid when Input is computer) Acceptable “000_%1” [CR] “1080PSF/24” ------- 1080psf 24Hz “1080P60”...
PLC-HF15000L Expand Serial Command Functional Specifications “AUTO” ------------------- indicates Auto is selected “NTSC” ------------------- indicates NTSC is selected “NTSC443” -------------- indicates NTSC4.43 is selected “PAL” ---------------------- indicates PAL is selected Input is Video “SECAM” ----------------- indicates SECAM is selected or S-video “PAL-M”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.7.5 CR_MODELIST Command Command “CR_MODELIST” [CR] Details Get possible modes for Mode list Acceptable “000_%1_%2_---_%x” [CR] Error Code “101” is returned except for PC-Analog and for no signal with PC-Analog Possible modes in Mode1-10 are returned when PC-Analog signal is coming.
PLC-HF15000L Expand Serial Command Functional Specifications 9.7.8 CR_SRCINP3 Command Command “CR_SRCINP3” [CR] Details Get Source of Input 3 Acceptable “000_%1” [CR] Response The same data as CF_SRCINP1 Unacceptable “?” [CR] 9.7.9 CR_SRCINP4 Command Command “CR_SRCINP3” [CR] Details Get Source of Input 4 Acceptable “000_%1”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.7.13 CR_NMSLOT3 Command Command “CR_NMSLOT3” [CR] Details Get the board name inserted to Slot 3 Acceptable “000_%1” [CR] Response The same data as CR_NMSLOT1 Unacceptable “?” [CR] 9.7.14 CR_NMSLOT4 Command Command “CR_NMSLOT4” [CR] Details Get the board name inserted to Slot 4 Acceptable “000_%1”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.7.17 CR_IDSLOT3 Command Command “CR_IDSLOT3” [CR] Get ID information on Slot 3. This command is to recognize the inserted slot board Details and specify the valid Input source. Acceptable “000_%1” [CR] Response The same as CR_IDSLOT1 Unacceptable “?”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.8.10 CR_SCREENASPECT Command Command “CR_SCREENASPECT”[CR] Details Get status of Screen aspect Acceptable “000_%1” [CR] “FULL” ÿ e ÿ e ÿ e ÿ e ÿ e ÿ e ÿ e Select Full screen mode “43MODE” ÿ...
PLC-HF15000L Expand Serial Command Functional Specifications 9.9 Lamp Status Read Commands 9.9.1 CR_LAMPREPL Command Command “CR_LAMPREPL” [CR] Details Get the information of Lamp Replacement time Acceptable “000_%1” [CR] “4****” 4 ---------------- indicates 4 lamps are used in this model. * ---------------- indicates the status of each lamp in lamp number order.
PLC-HF15000L Expand Serial Command Functional Specifications 9.9.5 CR_AUTOLAMPCONTRL Command Command “CR_AUTOLAMPCONTRL” [CR] Details Get selected Lamp control mode Acceptable “000_%1” [CR] “NORMAL” ---------- NORMAL is selected. “ECO1” --------------- ECO1 is selected. Response “ECO2” --------------- ECO2 is selected. “AUTO” -------------- AUTO is selected. Unacceptable “Error Code”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.9.10 CR_LAMPH Command Command “CR_LAMPH” [CR] Get Lamp running time (in hours) Details * return actual lamp running time Acceptable “000_%1_%2_%3_%4” [CR] Lamp 1 data comes first, and then one space, after that lamp 2 data is followed.
PLC-HF15000L Expand Serial Command Functional Specifications 9.10 Setting Status Read Commands 9.10.1 CR_LANG Command Command “CR_LANG” [CR] Details Get selected language Acceptable “000_%1” [CR] “ENG” -------------------------- English is selected “DEU” -------------------------- German is selected “FRA” -------------------------- French is selected “ITA” ---------------------------- Italian is selected “ESP”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.10.5 CR_PIP Command Command “CR_PIP” [CR] Details Get setting status of “Picture in Picture” Acceptable “000_%1” [CR] “OFF” -------------------- Off is selected “USER1” ---------------- User1 is selected “USER2” ---------------- User 2 is selected Response “USER3”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.10.14 CR_BLEND Command Command “CR_BLEND” [CR] Details Get all values set for Width in Edge blending Acceptable “000_%1_%2_%3_%4” [CR] Left width data comes first, and then one space, after that right width data is followed. %1 = Left width %2 = Right width %3 = Top width...
PLC-HF15000L Expand Serial Command Functional Specifications 9.10.17 CR_BLENDTESTPAT Command Command “CR_BLENDTESTPAT” [CR] Details Get setting status of Test pattern of Edge blending Acceptable “000_%1” [CR] “ON” ---------------------- On is selected Response “OFF” --------------------- Off is selected Unacceptable “Error Code” [CR] 9.10.18 CR_COLORMATCHING Command Command “CR_COLORMATCHING”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.10.21 CR_CMTGXY_%1 Command Command “CR_CMMTGXY_%1” [CR] Details Get “x””y” value of Target of Color matching Acceptable “000_%2” [CR] “RED” ---------------------- value of Red is selected “GREEN” ----------------- value of Green is selected “BLUE” -------------------- value of Blue is selected “WHITE”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.10.25 CR_CMTGTESTPAT Command Command “CR_CMTGTESTPAT” [CR] Details Get setting status of Test pattern(Target) of Color matching Acceptable “000_%1” [CR] “RED” ---------------------- Red is displayed “GREEN” ----------------- Green is displayed “BLUE” -------------------- Blue is displayed “WHITE”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.10.40 CR_SHUTKEYPROT Command Command “CR_SHUTKEYPROT” [CR] Details Get status if Shutter can be controlled by key on the side panel Acceptable “000_%1” [CR] “ON” ----------- Shutter is not controllable by key on the side panel Response “OFF”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.10.50 CR_FILREMAIN Command Command “CR_FILREMAIN” [CR] Details Get the value of Filter counter remaining (remaining life time of the air filter) (%). Acceptable “000_%1” [CR] “100” = Filter counter remaining is 100% Response ÿ “000”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.11 Other Status Read Commands 9.11.1 CR_STATUS Command Command “CR_STATUS” [CR] Get operating status of Projector Details Same as “CR0” in basic command except error code follows it. Acceptable “000_%1” [CR] “00” = Power ON “80”...
PLC-HF15000L Expand Serial Command Functional Specifications 9.11.5 CR_TEMPFAIL Command Command “CR_TEMPFAIL” [CR] Get the temperature inside the projector when the abnormal status occurs. Details It is possible to get the temperatures for more than one sensor all at once if it is applicable.
PLC-HF15000L Expand Serial Command Functional Specifications 9.11.6 CR_TEMP Command Command “CR_TEMP”[CR] Get the current temperature information inside a projector. Details It is possible to get the temperatures all at once when several sensors installed. Acceptable “000_%1_%2” [CR] %1 ------------------ Sensor 1 temp. (External temp.) %2 ------------------ Sensor 2 temp.
PLC-HF15000L Expand Serial Command Functional Specifications 9.11.9 CR_SERIALNO Command Command “CR_SERIALNO” [CR] ÿ Details Get value of the serial number. For Dealerÿ Acceptable “000_%1” [CR] Response Eight digits of alphanumeric characters Unacceptable “?” [CR] 103/105...
PLC-HF15000L Expand Serial Command Functional Specifications 10ÿ Command with Address Specification 10.1. Overview - Commands with address are used to remote control more than one projector through RS-232C by a computer. - The command with address is defined as a single command per line that starts with “A” and ends with carriage return (0x0D).
PLC-HF15000L Expand Serial Command Functional Specifications 10.2.2. When the command pipelining is needed When it needs command pipelining, the operation is the same as the remote control as below: Sending-side system issues commands every 100ms When receiving an applicable command, the function is executed repeatedly for 120ms.