Advertisement
Quick Links
Advertisement
Related Manuals for Asus UX562IA IQ
Summary of Contents for Asus UX562IA IQ
- Page 1 Disassembly Procedure ASUS UX562IA_IQ Repair Manual...
- Page 2 Disassembly Procedure...
- Page 3 Disassembly Procedure Service Overview ⚫ ASUS is not responsible for direct, indirect, intentional o unintentional damages resulting from improper installation and operation. ⚫ Carefully read through this Service Guide for a look at various components of the device before performing any service and repairs.
- Page 4 Disassembly Procedure Pre-repair checklist ⚫ Read the entire manual before starting any service procedures and follow all instructions. ⚫ Back up the data on your device. ⚫ Place your device on a clean and stable surface. ⚫ Turn off your device. ⚫...
- Page 5 Disassembly Procedure Service Overview Please pay special attention to the cautions below to prevent any damages to the notebook and please be sure to select the appropriate tools described in this section to perform any services desired. Precautions Before you perform any service or repair on the notebook, please follow the steps below first. 1.
- Page 6 Disassembly Procedure 9. Screw Appearance Criteria. If the screws have the following damaged appearance, please do not use. a. Shape deformed. b. Paint scratched off. c. Rusty. d. Damaged head – unable to drive in. e. Damaged unable to securely tighten. 10.
- Page 7 Disassembly Procedure Appropriate Tools The illustrations below show the appropriate tools that should be used for the notebook’s service and repair. ➢ Cross Screwdriver Please accord to different screw specification to choose different screwdriver and head. Below photos are for reference only. Use a cross screwdriver to fasten/remove screws.
- Page 8 Disassembly Procedure ➢ Thickness gauge Thickness compass specification 0.05mm-1.5mm. Use it to measure the gap.
- Page 9 Disassembly Procedure Bottom Case Module The illustrations below show how to remove the Bottom Case Module. Notice: After disassembling bottom case, if you want to replace any part, please be sure to disconnect the battery connector more than ten seconds to avoid damaging any part. 1.
- Page 10 Disassembly Procedure 3. Use plastic blade to pry Bottom Case and remove it. 4. Pull out battery cable. Snaps as below...
- Page 11 Disassembly Procedure Parts: ⚫ Total screw * 10 ⚫ BOTTOM CASE ASSY//*1 ⚫ (Actual part name depends on different SKU.)
- Page 12 Disassembly Procedure HDD Module The illustrations below show how to remove the HDD Module. Disconnect the HDD FFC and take out the HDD Module. Assembly Notice: Follow the reverse numbers to lock screws. 2. Remove the HDD Rubber, HDD FFC and HDD CONDUCTIVE TAPE. Parts: ⚫...
- Page 13 Disassembly Procedure Battery Module The illustrations below show how to remove the Battery Module. Disconnect the IO FFC and remove the acid cloth, antennas and EDP Cable. Please well arrange the EDP Cable and Antennas when assembled them.
- Page 14 Disassembly Procedure Follow below numbers to remove 5 screws on the battery module and take out the battery. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0KG±0.2kgf. 3. Remove the Battery. M2*4L (4.6,0.8) (K) B-ZN...
- Page 15 Disassembly Procedure Notice: Please stick new BATT AL FOIL when you assemble the Battery. Parts: ⚫ Total screw * 5 ⚫ Battery * 1 ⚫ (Actual part name depends on different SKU.)
- Page 16 Disassembly Procedure Speaker & Antenna Module The illustrations below show how to remove the Speaker & Antenna Module. 1. Disconnect the speaker cable and remove the acid cloth batt mylar. 2. Remove the antennas and speaker. Please well arrange the speaker cable and antennas when assembled.
- Page 17 Disassembly Procedure Parts: ⚫ Total screw * 0 ⚫ Speaker *1 ⚫ Antenna * 2 ⚫ (Actual part name depends on different SKU.)
- Page 18 Disassembly Procedure IO Board Module The illustrations below show how to remove the IO Board Module. 1. Remove 4 screws. Assembly Notice: follow the reverse numbers to lock screws. 3.0KG±0.2kgf M2*4L (4.6,0.8) (K) B-ZN 2.0KG±0.2kgf M2.5*4.5L (4.5,0.8) (K) B-ZN Rotate the hinge to take out the IO Board. Assembly notice: Please change new one, If FFC is damage during disassembly.
- Page 19 Disassembly Procedure Parts: ⚫ Total screw * 4 ⚫ HDMI Board * 1 ⚫ (Actual part name depends on different SKU.)
- Page 20 Disassembly Procedure SSD Module The illustrations below show how to remove the SSD Module. 1. Remove 1 screw and take out the SSD Module. Screw tightening torque (Kg F-cm): 2.0KG±0.2kg SSD & SSD AL FOIL THM SSD PAD M2*4L(4.6,0.8) Parts: ⚫...
- Page 21 Disassembly Procedure Thermal & Fan Module The illustrations below show how to remove the Thermal & Fan Module. 1. Disconnect the fan cable from mainboard. 2. Remove 5 screws on the Thermal & FAN Module. Assembly Notice: follow the reverse numbers to lock screws. Screw tightening torque: 2.0KG±0.2kgf Screw tightening torque: 2.0KG±0.2kgf M2*2.5L (K) W-NI...
- Page 22 Disassembly Procedure 3. Disconnect Thermal & Fan Module. Location: [GPU/CPU] Thermal material: 16TT0-R004H000 GA500 Grease thickness about 0.2~0.3mm ⚫ Please use the correct technique of taking fans in order to avoid being out of shape. Correct demonstration Wrong demonstration Parts: ⚫...
- Page 23 Disassembly Procedure Motherboard Module The illustrations below show how to remove the Motherboard Module. 1. Disconnect TP CMOS Cable, TP FFC, Backlight Keyboard Cable. 2. Remove 7 screws on the Mainboard. Assembly Notice: follow the reverse numbers to lock screws.
- Page 24 Disassembly Procedure M2.5*4.5L (4.5,0.8) 3.0KG±0.25kgf M2*2.5L (K) W-NI 2.0KG±0.2kgf M2*4L (4.6,0.8) 2.0KG±0.2kgf Parts: ⚫ Total screw * 7 ⚫ MAIN_BD *1 ⚫ (Actual part name depends on different SKU.)
- Page 25 Disassembly Procedure Notice: These pictures for your reference for mylar/gasket/sponge etc. of MB. 1. SSD MYLAR 2. CPU CAPTON 3. HOOK BLOCK 4. THM SSD PAD...
- Page 26 Disassembly Procedure Touchpad Module The illustrations below show how to remove the Touchpad Module. 1. Disconnect the TP FFC. Notice: Insert FFC to the bottom until just accord with the line when lock the latch. 2. Remove 3 screws on Touch Pad and take out it. Assembly Notice: follow the reverse numbers to lock screws.
- Page 27 Disassembly Procedure Assembly notice: Please change new one, If FFC is damage during disassembly. Here are some samples of FFC damage: Parts: ⚫ Total screw * 3 ⚫ TP FFC *1 ⚫ TOUCHPAD *1 ⚫ (Actual part name depends on different SKU.)
- Page 28 Disassembly Procedure Keyboard Module The illustrations below show how to remove the Keyboard Module. Remove the Keyboard. Parts: ⚫ Total screw * 0 ⚫ Keyboard Module *1 ⚫ (Actual part name depends on different SKU.)
- Page 29 Disassembly Procedure LCD Module The LCD Module（for UX564 EH EI ）does not need to disassemble for repair – This part has been packed as module.