Advertisement
Available languages
Available languages
Installation Manual of Room Air Conditioner
Preparation
Necessary Tools for Installation
Driver
Nipper
Hacksaw
Hole core drill
Spanner(17,19 and 26mm)
Gas leakage detector or
soap-and-water solution
Power Source
Before inserting power plug into receptacle, check the voltage without fail.
The power source is the same as the corresponding name plate.
Install an exclusive branch circuit of the power.
A receptacle shall be set up in a distance where the power cable can be
reached.Do not extend the cable by cutting it.
Drawing for the installation of indoor and outdoor units
The models adopt HFC free refrigerant R410A
more than 5cm
more than10cm
Indoor unit B
Arrangement of piping
directions
Rear left
Rear
Left
right
Right
Below
The marks from
to
A
in the figure are the
G
parts numbers.
The distance between
the indoor unit and the
floor should be more
than 2m.
Read this manual before installation
Explain sufficiently the operating means to the user according to this manual
NO.00105
Torque wrench
(17mm,22mm,26mm)
Pipe cutter
Flaring tool
Knife
Measuring tape
Reamer
Indoor unit A
more than 10cm
more than 10cm
more than 10cm
more than 60cm
Please be subject to the actual product purchased ,
the above picture is just for your reference.
Selection of Installation Place
Indoor Unit
Place, robust not causing vibration, where the body can be supported sufficiently.
Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the
unit are not disturbed.
Place, possible to drain easily, where piping can be connected with the outdoor unit.
Place, where cold air can be spread in a room entirely.
Place, nearby a power receptacle, with enough space around. (Refer to drawings).
Place where the distance of more than lm from televisions, radios, wireless apparatuses
and fluorescent lamps can be left.
In the case of fixing the remote controller on a wall, place where the indoor unit can
receive signals when the fluorescent lamps in the room are lightened.
Outdoor Unit
Place, which is less affected by rain or direct sunlight and is sufficiently ventilated.
Place, possible to bear the unit, where vibration and noise are not increased.
Place, where discharged wind and noise do not cause a nuisance to the neighbors.
Place, where a distance marked
Attention must be paid to
the rising up of drain hose
F
C
D
E
more than15cm
is available as illustrated in the above figure.
Optional parts for piping
Non-adhesive tape
A
Adhesive tape
B
Saddle (L.S) with screws
C
Connecting electric cable
D
for indoor and outdoor
E
Drain hose
F
Heating insulating material
G
Piping hole cover
Floor fixing dimensions of the
outdoor unit (Unit:mm)
106.5
566
106.5
Fixing of outdoor unit
Fix the unit to concrete or block
with bolts (10mm) and nuts firmly
and horizontally.
When fitting the unit to wall
surface, roof or rooftop, fix
a supporter surely with nails
or wires in consideration of
earthquake and strong wind.
If vibration may affect the
house, fix the unit by attaching a
vibration-proof mat.
Advertisement
Table of Contents
Related Manuals for Haier 2HUM14HB03
Summary of Contents for Haier 2HUM14HB03
-
Page 1: Installation Manual Of Room Air Conditioner
Place, robust not causing vibration, where the body can be supported sufficiently. Hacksaw Pipe cutter Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the Hole core drill Flaring tool unit are not disturbed. -
Page 2: Indoor Unit
When connecting the cable before installing the indoor unit Ø60mm Insert the cable from the back side of the unit, then pull it out on the front side. Loosen the screws and insert the cable ends fully into terminal block, then... -
Page 3: Outdoor Unit
Install according to Connection of pipes 4G0.75mm To bend a pipe, give the roundness as large as possible not to crush the pipe , Outdoor unit B and the bending radius should be 30 to 40 mm or longer. Indoor unit A Connecting the pipe of gas side first makes working easier. -
Page 4: Refrigerant Charge Label
The end is imm- It waves. The gap with the There is the bad To prevent the gas leakage, turn the service port’s cap, the valve rod’s cap for 2-way high midway. ersed in water. ground is too small. smell from a ditch valve and 3-way’s a little more than the point where the torque increases suddenly. - Page 5 Elija un lugar que permita soportar el peso de la unidad y que no amplifique el ruido y las vibraciones. Seleccione un lugar en el que los residuos y el viento generado por la unidad no cause una molestia a los vecinos.
- Page 6 1. Pase la manguera aislante a través del hueco de los materiales de aislamiento de Accesorios calor de la unidad interior. 2. Inserte los cables eléctricos de interior / exterior a través de la parte trasera de la unidad interior y tire de ellos desde la parte delantera. A continuación, conéctelos. Manguera de Control remoto (1) 3.
-
Page 7: Unidad Exterior
Procure que no penetren materiales, como residuos o arena, en el tubo. La longitud estándar del tubo es de 5m. Si la longitud total del tubo es superior a 20m, se verá afectado el funcionamiento de la unidad, y deberá cargarse el refrigerante a razón de 20 g/m. - Page 8 7. Para evitar fugas de gas, gire el tapón del puerto de mantenimiento y el tapón del vástago de las válvulas de 2 y 3 vías un poco por encima del punto en el que la Deposite agua en la bandeja de drenaje de la unidad interior y confirme que el torsión aumenta súbitamente.
- Page 9 Attenersi al prodotto acquistato: le immagini sono solo per antivibrazione. riferimento Leggere questo manuale prima dell’installazione Spiegare all’utente in modo esauriente il funzionamento e l’uso del condizionatore in base alle istruzioni di questo manuale.
- Page 10 Allentare le viti ed inserire completamente le estremità del cavo nel blocco terminali, poi stringere le viti. Tirare leggermente il cavo per accertarsi che i cavi siano stati inseriti e fissati in modo appropriato. Dopo avere collegato i cavi, non dimenticare mai di stringere i cavi collegati con la copertura dei cavi.
- Page 11 1. Staccare il coperchio della porta di servizio della valvola a 3 vie, il coperchio collegamento è H05RN-F o H07RN-F. della valvola a stelo della valvola a 2 vie e della valvola a stelo della valvola a 3 2. Se il fusibile della scheda PC è saltato, sostituirlo con uno di tipo T.3.15A/250VAC vie, collegare la porta di servizio nella protuberanza del tubo di carico (basso) (interno), T.25A/250VAC (esterno).
- Page 12 Dopo avere attivato di nuovo il degassamento ed aspirato l'aria, riempire con refrigerante raccomandato usando la bombola del gas. 6. Staccare il tubo di carico dalla porta di servizio, aprire la valvola a 2 vie ed a 3 vie. Girare l'asta della valvola in senso antiorario delicatamente.
- Page 13 Clé dynamométrique (17 mm, 22 mm, L'emplacement ne doit pas être affecté par de la chaleur ou de la vapeur générées 26 mm) dans les environs et doit garantir que l'entrée et la sortie de l'unité ne seront pas Pince Coupe-tube gênées.
-
Page 14: Unité Intérieure
Lors du cintrage, prenez soin de ne pas écraser les tuyaux. 1. Exécutez une mise à niveau correcte de la plaque à fixer contre le mur en fonction Connectez au préalable le câble des unités intérieures/extérieures et recouvrez des piliers ou des linteaux autour, puis attachez la plaque temporairement avec un ensuite les câbles connectés avec l'isolation. - Page 15 3. 4. En tournant dans le sens antihoraire, ouvrez le robinet de la vanne à 2 voies à un angle de 90 degrés. Environ 6 secondes plus tard, fermez la vanne à 2 voies et...
- Page 16 Après avoir effectué l'évasement et le vide, remplissez de réfrigérant Moins de indiqué de la bouteille. 6. Détachez le tuyau de charge de l'orifice d'entretien, ouvrez la vanne à 2 et 3 voies. Tournez le robinet de la vanne dans le sens antihoraire. L'intervalle au sol Il est surélevé...