Panasonic LP-400 Series Operation Manual
Co2 laser marker
Hide thumbs
Also See for LP-400 Series:
- Operation and maintenance manual (334 pages) ,
- External control manual (180 pages)
Related Manuals for Panasonic LP-400 Series
Summary of Contents for Panasonic LP-400 Series
- Page 1 Laser Marker LP-400 SERIES Operation Manual ME-LP400-OP-18 2013.7 panasonic.net/id/pidsx/global...
- Page 2 REFERENCE Note 1. This manual is subject to LP-400 Series. This manual uses illustrations and screens of LP-400 Series standard model type. Note that the illustrations shown in these manuals might be different. 2. Contents of this manual will be changed without notice. This manual and software must not be partially or totally copied or revised.
-
Page 3: General Terms And Conditions
(2) Any Products found to be defective must be shipped to Panasonic Industrial Devices SUNX with all shopping costs paid by Purchaser or offered to Panasonic Industrial Devices SUNX for inspection and examination. Upon examination by Panasonic Industrial Devices SUNX, Panasonic Industrial Devices SUNX will, at its sole discretion, repair or replace at no charge, or refund the purchaser price of, any Products found to be defective. - Page 4 Trademarks Windows is a registered trademark or trademark of U.S.A. Microsoft Corporation in U.S.A and other countries. All other product names and companies provided in this manual are trademarks or registered trademarks of their respective companies. QR Code is the registered trademarks of DENSO WAVE INCORPORATED. Applicable Standards and Product Model This product is applied the following standards.
-
Page 5: License Agreement
"Panasonic Industrial Devices SUNX Co., LTD." support number provided in the documentation for the DEVICE. Should you have any questions concerning this EULA, or if you desire to contact "Panasonic Industrial Devices SUNX Co., LTD." for any other reason, please refer to the address provided in the documentation for the DEVICE. - Page 6 Caution in Handling Laser Beam The product uses the laser beam of Class 4 (marking laser) and Class 2 (guide laser) classified by “Safety of laser products“ (JIS C 6802), US standard (FDA 21 CFR 1040.10 and 1040.11), and international standard (IEC60825-1).
- Page 7 ■ Laser Radiation Range [Unit: mm] LP-4xxU / LP-42XS9U (Standard head type) NOHD [Unit: mm] LP-4xxTU / LP-42XS9TU (Tower head type) NOHD [Unit: mm] Model Specified Point LP-431U LP-431TU LP-430U LP-430TU LP-435U LP-435TU LP-410U LP-410TU LP-411U LP-411TU LP-421S9U LP-421S9TU LP-420S9U LP-420S9TU LP-425S9U LP-425S9TU...
- Page 8 DANGER Never look at laser beam directly or through lens. Diffused reflected beam is also harmful. laser does not enter into eye's retina, however, if it exposed to the eyes, it can inflict severe corneal injuries. WARNING Wear laser protective goggles for operator's eyes. The goggles should be used against scattered beam, so avoid to direct beam or reflection beam.
- Page 9 Safety Protection Measures This product falls into Class 4 laser (marking laser) and Class 2 laser (guide laser) based on the classifica- tions of the Safety of laser products (JIS C 6802) / FDA standards 21 CFR 1040.10 and 1040.11/IEC60825-1. Perform the safety protection measure shown below before using the system.
-
Page 10: Protective Clothing
7. Termination of laser beam High output laser is used for marking taking into consideration a case where there is no substrate in a laser path, terminate a laser beam path within the marking range by using a flame-resistant object. Do not use the laser for the end edge of the specular reflexion.