Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DCG406N-XJ
Summary of Contents for DeWalt DCG406N-XJ
- Page 1 DCG406 Final page size: A5 (148mm x 210mm)
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A 90˚ 90˚ Fig. B...
- Page 4 Fig. C Fig. D Fig. E Fig. F Fig. G...
-
Page 5: Definitions: Safety Guidelines
English CORDLESS SMALL ANGLE GRINDER DCG406 Congratulations! and the accessories, keep the hands warm, organisation of work patterns. You have chosen a D WALT tool. Years of experience, thorough EC-Declaration of Conformity product development and innovation make D WALT one of the most reliable partners for professional power tool users. -
Page 6: Work Area Safety
Weight English Batteries Chargers/Charge Times (Minutes) Cat # Weight (kg) DCB107 DCB113 DCB115 DCB118 DCB132 DCB119 DCB546 18/54 6.0/2.0 1.05 DCB547 18/54 9.0/3.0 1.25 DCB181 0.35 DCB182 0.61 DCB183/B 0.40 DCB184/B 0.62 DCB185 0.35 DCB187 0.48 e ) When operating a power tool outdoors, use an Denotes risk of fire. -
Page 7: Safety Instructions For All Operations
English ADDITIONAL SPECIFIC SAFETY RULES will do the job better and safer at the rate for which it was designed. Safety Instructions for All Operations b ) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled a ) This power tool is intended to function as a with the switch is dangerous and must be repaired. -
Page 8: Causes And Operator Prevention Of Kickback
English personal protective equipment. Fragments of b ) Never place your hand near the rotating accessory. workpiece or of a broken accessory may fly away and Accessory may kickback over your hand. cause injury beyond immediate area of operation. c ) Do not position your body in the area where power j ) Hold the power tool by insulated gripping surfaces tool will move if kickback occurs. -
Page 9: Important Safety Instructions For All Battery Chargers
English Residual Risks operations, is moving away from your body, the possible kickback may propel the spinning wheel and the power In spite of the application of the relevant safety regulations tool directly at you. and the implementation of safety devices, certain residual risks c ) When wheel is binding or when interrupting a cut cannot be avoided. -
Page 10: Charger Operation
English WARNING: Shock hazard. Do not allow any liquid to get electric shock. Removing the battery pack will not reduce inside charger. Electric shock may result. this risk. WARNING: We recommend the use of a residual current • NEVER attempt to connect two chargers together. device with a residual current rating of 30mA or less. -
Page 11: Wall Mounting
English when the battery pack needs to be cooled. Never operate the Do not incinerate the battery pack even if it is severely • charger if the fan does not operate properly or if ventilation slots damaged or is completely worn out. The battery pack can are blocked. -
Page 12: Storage Recommendations
English All lithium-ion batteries have the Watt Hour rating marked on the pack. Furthermore, due to regulation complexities, D WALT does not recommend air shipping lithium-ion battery packs Read instruction manual before use. alone regardless of Watt Hour rating. Shipments of tools with batteries (combo kits) can be air shipped as excepted if the Watt Hour rating of the battery pack is no greater than 100 Whr. -
Page 13: Intended Use
English Features • Check for damage to the tool, parts or accessories which may have occurred during transport. Kickback Brake™ • Take the time to thoroughly read and understand this manual When a pinch, stall, or bind-up event is sensed, the electronic prior to operation. - Page 14 English To Remove the Battery Pack from the Tool wheel where surface grinding is forbidden. Cutting can also be performed by using a Type 41 wheel and a Type 1 guard. 1. Press the release button 10 and firmly pull the battery pack nOTE: See the Accessory Chart to select the proper guard / out of the tool handle.
-
Page 15: Prior To Operation
English 1. Place the tool on a table, guard up. Mounting Wire Cup Brushes and Wire Wheels (Fig. A) 2. Install the backing flange 5 on spindle 4 with the raised centre (pilot) facing the wheel. Press the backing flange WARNING: Failure to properly seat the flange/ clamp nut/ into place. - Page 16 English Spindle Lock (Fig. A) WARNING: • Ensure all materials to be ground or cut are secured The spindle lock is provided to prevent the spindle from 3 in place. rotating when installing or removing wheels. Operate the • Secure and support the workpiece. Use clamps or a spindle lock only when the tool is turned off, unplugged from vice to hold and support the workpiece to a stable the power supply, and has come to a complete stop.
-
Page 17: Cutting Metal
English Precautions To Take When Working on a NOTICE: Edge grinding/cutting with a Type 27 wheel must be limited to shallow cutting and notching—less Painted Workpiece than 13 mm in depth when the wheel is new. Reduce the 1. Sanding or wire brushing of lead based paint is NOT depth of cutting/notching equal to the reduction of the RECOMMENDED due to the difficulty of controlling the wheel radius as it wears down. -
Page 18: Protecting The Environment
English Working Advice Max. Min. Periphical Threaded [mm] Rotation speed hole length Exercise caution when cutting slots in structural walls. [mm] Slots in structural walls are subject to the country-specific [min. –1 [m/s] [mm] regulations. These regulations are to be observed under all circumstances.Before beginning work, consult the responsible 115 –... -
Page 19: Accessory Chart
English Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Locking flange Wire wheels with threaded nut Type 27 guard Wire wheel Wire cup with threaded nut... - Page 20 English Accessory Chart (cont.) guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal Backing flange cutting disc, bonded Cutting wheel Diamond cutting Locking flange wheels Type 1 Guard Type 27 Guard...
- Page 24 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)