Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: P L EASE READ THESE I N STRUCT I O NS CAREFULLY. NOTE THE SAFE O P E RAT I O NAL RE Q U I R EMENTS, WARN I N GS & CAUT I O NS. USE
THE P R ODUCT CORRECTLY AND W I T H CARE FOR THE P U R P O SE FOR WH I C H I T I S I N TENDED. FA I L URE TO DO SO MAY CAUSE DAMAGE AND/OR
P E RSONAL I N JURY AND W I L L I N VAL I D ATE THE WARRANTY.
Refer to
Wear eye
instructions
protection
1. SAFETY
9
Follow all workshop safety rules, regulations, and conditions when using wrench.
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
9
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Non-authorised parts
may be dangerous and will invalidate the warranty.
‰
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Only use impact sockets which are specifically designed for use with a ratchet wrench.
9
Wear approved safety eye/face shield, ear defenders, and hand protection.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
9
Keep children and non essential persons away from the working area.
DO NOT use the wrench for a task it is not designed to perform.
8
‰
WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
DO NOT use wrench unless you have been instructed in its use by a qualified person.
8
8
DO NOT expose the comfort grip to excessive heat.
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
8
8
DO NOT operate wrench if you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT carry wrench with your hand on the power trigger in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. INTRODUCTION
Composite cover moulded around lightweight aluminium alloy housing reduces effects of chill on operator's hands and provides added control.
Air motor with quality bearings for smooth and powerful operation. Exhaust outlet adjusts 360°, keeping airflow away from operator. Features
twist-reverse action and trigger operated power control. Hardened gear and yoke assembly ensures suitability for the professional workshop.
3. SPECIFICATION
MODEL No:
Drive size
Max torque
Air consumption
Operating pressure
Inlet size
Vibration/Uncertainty
Noise Power / Pressure
Free Speed
4. PREPARATION
4.1.
AIR SUPPLY
WARNING! Ensure the air supply is clean and does not exceed 90 psi while operating the die wrench. Too high an air pressure and
‰
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.1.
Recommended hook-up procedure is shown in fig.1.
Ensure wrench air valve (or trigger) is in "off" position before connecting to the air supply.
4.1.2.
You will require an air pressure of 90psi, and an air flow according to specification.
4.1.3.
Drain the air tank daily. Water in the air line will damage the wrench.
4.1.4.
Clean air inlet filter weekly.
4.1.5.
Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
4.1.6.
Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
© Jack Sealey Limited
All manuals and user guides at all-guides.com
3/8" / 1/2" SQ DRIVE AIR RATCHET WRENCH
MODEL NO:
Wear protective
Wear ear
gloves
protection
SA607.V2
SA608.V2
3/8"Sq
1/2"Sq
50lb.ft (68Nm)
50lb.ft (68Nm)
4cfm
4cfm
90psi
90psi
1/4"BSP
1/4"BSP
0.44/0.22m/s²
0.44/0.22m/s²
84/83dB.A
85/83dB.A
200rpm
200rpm
Original Language Version
SA607.V2, SA608.V2
Wear face
mask
SA607.V2, SA608.V2
Issue 2 (H,F) 06/08/21
Advertisement
Related Manuals for Sealey SA608.V2
Summary of Contents for Sealey SA608.V2
- Page 1 SA607.V2, SA608.V2 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: P L EASE READ THESE I N STRUCT I O NS CAREFULLY. NOTE THE SAFE O P E RAT I O NAL RE Q U I R EMENTS, WARN I N GS & CAUT I O NS. USE THE P R ODUCT CORRECTLY AND W I T H CARE FOR THE P U R P O SE FOR WH I C H I T I S I N TENDED.
- Page 2 Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty. If the air system does not have an oiler, lubricate the air wrench daily with a few drops of Sealey air tool oil dripped into the air inlet 6.1.
- Page 3 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...