hit counter script
Panasonic KX-TS100EXW Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Telephone
  5. KX-TS100EXW
  6. Service manual

Panasonic KX-TS100EXW Service Manual

Telephone equipment
Hide thumbs Also See for KX-TS100EXW:
Table of Contents

Advertisement

Quick Links

Download this manual
ORDER NO. KM40201786C2
Telephone Equipment
KX-TS100EXW
Integrated Telephone System
White Version
(for Europe)
SPECIFICATIONS

Advertisement

Table of Contents
loading

Related Manuals for Panasonic KX-TS100EXW

Summary of Contents for Panasonic KX-TS100EXW

  • Page 1 ORDER NO. KM40201786C2 Telephone Equipment KX-TS100EXW Integrated Telephone System White Version (for Europe) SPECIFICATIONS...

  • Page 2: Location Of Controls

    1. LOCATION OF CONTROLS 2. CONNECTION...

  • Page 3: Connecting The Handset/Telephone Line Cord

    2.1. Connecting the Handset/Telephone Line Cord After connection, lift the handset to check for a dial tone. - Use only a Panasonic Handset for the KX-TS100EXW. 2.2. Connecting a Communication Device If you connect a communication device (computer, modem, fax, answering machine, etc.) to the telephone line, you can connect it through this unit using the DATA jack.
  • Page 4 - Make sure the communication device is not in use before using this unit (making calls, storing phone numbers in memory etc.) or the communication device may not operate properly. 3. OPERATIONS 3.1. Making Calls...

  • Page 5: Answering Calls

    3.2. Answering Calls...

  • Page 6: Special Features

    4. SPECIAL FEATURES...
  • Page 7 4.1. RECALL Button 4.2. How to Use the PAUSE Button (For Analog PBX Line/Long Distance Service Users) 4.3. How to Use the PAUSE Button (For Analog PBX Line/Long Distance Service Users) 5. DISASSEMBLY INSTRUCTIONS...

  • Page 8: How To Replace Flat Package Ic

    Ref. No. Procedure Shown in Fig —. To remove —. Remove —. Lower Cabinet Screws (2.6 × 12)..... (A) × 5 1 ~ 2 Printed Circuit Board Remove the P.C.Board 6. HOW TO REPLACE FLAT PACKAGE IC 6.1. Preparation - SOLDER Sparkle Solder 115A-1, 115B-1 or Almit Solder KR-19, KR-19RMA - Soldering iron Recommended power consumption will be between 30 W to 40 W.
  • Page 9 *Most important matter is accurate setting of IC to the corresponding soldering foil. 2. Apply flux for all pins of FLAT PACKAGE IC. 3. Solder employing specified solder to direction of arrow, as sliding the soldering iron. 6.3. Modification Procedure of Bridge 1.

  • Page 10: Terminal Guide Of The Ics, Transistors And Diodes

    8. TERMINAL GUIDE OF THE ICs TRANSISTORS AND DIODES 9. IC BLOCK DIAGRAM...

  • Page 11: Option Jumper Table

    10. OPTION JUMPER TABLE 10.1. Dialing Mode SW SW Position Pin 14 LOW Tone dialing 10 pps Pin 14 High Pulse dialing 10.2. Flash Key Flash time Option 98 ms 305 ms 600 ms default 11. BLOCK DIAGRAM (IC2)

  • Page 12: Circuit Operations

    12. CIRCUIT OPERATIONS Note: The circuit diagram may be modified at any time with the development of new technology. 12.1. Telephone Line Interface When the hook switch SW1 is ON (off-hook), the circuit is closed, and current is supplied to the base of Q2 via the diode bridge D1 and Q2 is On Q1 is ON (OFF-HOOK condition).

  • Page 13: Ringer Circuit

    to output the signal to line. Shown below is the signal flow used to output the DTMF signal from the handset as a monitor tone when a dial key is pressed. Pin 11 of IC1 Handset Speaker. The signal combination and frequency corresponding to each dial key is shown on next page. Tone Frequencies High Group Low Group...

  • Page 14: Power Circuit And Redial Back-Up Circuit

    SW3 then impressed on the ceramic sound generator, and so is generated. Output frequency is controlled by R2 and C3 following below formula. 12.4. Power Circuit and Redial Back-up Circuit Function: This set is powered from the line. When it is an OFF-HOOK status, Tel Line pin 17 of IC1 (to become the power supply for IC1 speech network).

  • Page 15: Service Hints

    13.1. Service Hints SYMPTOM CURE No Tone Dialing. Check IC1, Q3, Q9, R37, R38, R34 and R35. Dead. Check IC1, Q2 and Q1. Rings, no dial tone or tone dial. Check Q1, Q2, D1. No rings. Check C1, R1, R3 and IC2. 13.2.

  • Page 16: Cabinet And Electrical Parts Location

    13.4. Problems With Ringer Check R1, C1, IC2, R3, C37, R2, C3, C2. 13.5. How to Check the IC1 (Scanning to the key) 14. CABINET AND ELECTRICAL PARTS LOCATION...

  • Page 17: Accessories And Packing Materials

    15. ACCESSORIES AND PACKING MATERIALS...

  • Page 18: Replacement Parts List

    16. REPLACEMENT PARTS LIST Note: 1. RTL (Retention Time Limited) The marking (RTL) indicates that the Retention Time is limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of availability depends on the type of assembly and the laws governing parts and product retention.
  • Page 19 At the end of this period, the assembly will no longer be available. 2. Important safety notice Components identified by the mark indicates special characteristics important for safety. When replacing any of these components, only use specified manufacture's parts. 3. The S mark means the part is one of some identical parts. For that reason, it may be different from the installed part.
  • Page 20 Ref. No. Part No. Part Name & Description Remarks PCB1 PQWPTS100EXW MAIN P.C BOARD ASS'Y (RTL) (ICS) C1CA00000250 PQVILS1240A (TRANSISTORS) 2SA1625 TRANSISTOR(SI) PQVT2N6517CA TRANSISTOR(SI) 2SC2120 TRANSISTOR(SI) 2SD1819A TRANSISTOR(SI) 2SD1819A TRANSISTOR(SI) 2SD1819A TRANSISTOR(SI) 2SD1819A TRANSISTOR(SI) PQVTFB1A4M TRANSISTOR(SI) 2SD1819A TRANSISTOR(SI) UN5113 TRANSISTOR(SI) 2SD1819A TRANSISTOR(SI) 2SD1819A...
  • Page 21 Ref. No. Part No. Part Name & Description Remarks ERDS2TJ564 560k ERDS2TJ683 ERJ3GEYJ104 100k ERJ3GEYJ104 100k ERDS2TJ332 3.3k ERJ3GEYJ392 3.9k ERJ3GEYJ822 8.2k ERJ3GEYJ222 2.2k ERJ3GEYJ560 ERDS1TJ150 ERJ3GEYJ103 ERJ3GEYJ475 4.7M ERJ3GEYJ560 ERJ3GEYJ392 3.9k ERJ3GEYJ333 ERJ3GEYJ224 220k ERJ3GEYJ273 ERJ3GEYJ103 ERJ3GEYJ335 3.3M ERJ3GEYJ272 2.7k ERJ3GEYJ331 ERJ3GEYJ333...
  • Page 22 Ref. No. Part No. Part Name & Description Remarks ERJ3GEYJ102 R188 ERJ3GEYJ104 100k (CAPACITORS) ECQE2155T370 ECEA1HKS100 ECUV1C563KBV 0.056 ECKD2H681KB 680p ECKD2H681KB 680p ECUV1H103KBV 0.01 ECUV1H103KBV 0.01 ECEA1VU330 ECEA1EU470 ECUV1C393KBV 0.039 ECEA1AU221 ECUV1C104KBV ECUV1H102KBV 0.001 ECUV1H331JCV 330p ECUV1C104KBV ECUV1C104KBV ECUV1C104KBV ECEA1HU100 ECUV1H333KBV 0.033 ECUV1H103KBV...

  • Page 23: For Schematic Diagram

    Ref. No. Part No. Part Name & Description Remarks PQJA10075Z TEL CORD PQJA212M CURL CORD PQJXC0202Z HANDSET PQKL10038Y1 WALL MOUNT ADAPTOR PQQW12610Z LEAFLET PQQX13329Z INSTRUCTION BOOK (for English) PQQX13330Z INSTRUCTION BOOK (for Spanish) PQQX13331Z INSTRUCTION BOOK (for Dutch) PQPH89Y POLY BAG PQPK13677Z GIFT BOX 17.
  • Page 24 SW25 E C B C186 R111 JJ102 C181 R184 C187 JJ101 POS1 E C B E C B [BREAK 60%] [BREAK 66%] RINGER H/S_JACK BLACK KX-TS100EXW CIRCUIT BOARD (Flow Solder Side View)
  • Page 25 4.10 0.00 0.00 0.00 0.00 4.10 0.00 4.47 1.47 0.00 1.45 0.64 1.43 0.00 0.35 0.00 0.00 0.00 0.00 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 4.10 KX-TS100EXW SCHEMATIC DIAGRAM...
  • Page 26 PROGRAM PAUSE REDIAL FLASH AUTO SHARP Q182 Q183 KX-TS100EXW CIRCUIT BOARD (Component View)

Table of Contents