Operating Instructions Video Monitor WV-LW1900 Model No. WV-LW2200 (This illustration represents WV-LW2200.) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual.
Page 2
This product has a fluorescent lamp that contains mercury. Dispose may be regulated in your community due to environ- mental considerations. For disposal or recycling information, please contact your local authorities, or the Electronic Industries Alliance: http://www.eiae.org WARNING: • This apparatus must be earthed. •...
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
AND/OR THE CORRESPONDING PRODUCT (S). Disclaimer of warranty IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW: (1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;...
Language in the menus to be displayed ... 18 Operation time check ... 19 Installation ... 20 How to mount monitor stand ... 20 How to remove monitor stand mounting bracket ... 20 Screw holes for wall mounting bracket ... 20 Connections ... 21 Troubleshooting ... 23 Specifications ...
Preface This is a video monitor provided with a 19"-type (WV- LW1900) or a 22"-type (V) (WV-LW2200) LCD panel. • Built-in full high-definition panel (for WV-LW2200)/high- definition panel (for WV-LW1900) with high-speed response • Supporting HDMI, composite video signal and analog RGB signal for personal computer (PC) •...
Page 7
Failure to observe this may cause damage to the LCD panel. • The LCD panel is made from a very precise technolo- Some bright and dark spots may exist on the monitor screen. It is operating normally if there are 99.99 % active pix- els.
Installation place • This monitor is designed to be used indoors. This moni- tor is not operable outdoors. • Keep the both side surfaces, top surface and rear sur- face of this monitor approximately 5 cm away from the wall.
This indicator lights green while power is supplied to this monitor and lights orange in the ECO mode ( page 14). When this monitor power is turned off, it lights red. e Input signal selection button (INPUT SELECT) Every pressing this button can change input signals as follows.
(3 to 3.26 mm x 7 to 7.26 mm x 3.5 to 4 mm). Use a strong cord or chain (locally procured) to secure this monitor to a solid wall or column for fall prevention. Remove the clamp when a mounting bracket for wall installation is used.
Page 11
Timing data chart for PC input This monitor supports the timing data listed as follows. The timing data are partly applicable to the items not listed in the table below. Resolution Refresh frequency (Hz) 640 x 480 800 x 600...
(cameras, digital disk recorders, etc.). ( page 21) z Press the power button. → The monitor will be powered on, and the power indi- cator will light up in green. x Press the INPUT SELECT button. Every pressing this button can change input signals as follows: →...
Audio Volume Control z Pressing the audio buttons (AUDIO –/+) during image display allows users to adjust the audio volume level. When the button is pressed, the volume level appears on the bottom of the screen. – : Audio volume down + : Audio volume up VOLUME Item...
ECO Mode Activation/Deactivation The ECO mode is a mode that can reduce the power con- sumption of this monitor by darkening or completely turning off the backlight of the LCD panel. The power indicator lights orange while the ECO mode is activated.
Video Adjustment and Setup Video adjustment Adjustment of this monitor will be performed in the VIDEO ADJUST menu. The menu title display differs depending on the selected input signal. Before adjustment, press the INPUT SELECT button surely to select the input signal.
Note: • [USER COLOR R], [USER COLOR G], and [USER COLOR B] can be adjusted only if [User] has been cho- sen for [COLOR TEMPERATURE]. v To reset the video adjustment to the default, use the C/D buttons to select "NORMAL SETTINGS" and press the menu button.
Page 17
v Use the C/D buttons to select the item to be adjusted, and press the -/+ buttons to adjust the screen. Item Effect H-POSITION Leftward Leftward V-POSITION (except video) Lower Upper CLOCK (only for PC) Smaller Larger PHASE (only for PC) Minimum Maximum Note: •...
Language in the menus to be displayed A language in the screen is selectable. z Press the menu button. → The main menu appears. ( page 15) x Use the C/D buttons to select "LANGUAGE", and press the menu button. V I D E O A D J U S T S C R E E N S E T U P M A I N T E N A N C E...
Operation time check The approximate time period of the monitor operation from startup to the present can be viewed. z Press the menu button. → The main menu appears. ( page 15) x Use the C/D buttons to select "MAINTENANCE", and press the menu button.
• Before installation work, remove all the connected cables and turn off the power of this monitor. • Do not block the ventilation opening. • Install this monitor at a vibrationless place. Installation of this monitor at a constantly vibrating place may cause trouble. How to mount monitor stand The monitor stand (accessory) is mounted.
Connections Another video monitor PC output Video input Power cord * Use a cord clamp to fasten the (accessory) HDMI cable and power cord. Audio output HDMI output Video output Digital disk recorder...
Connect the audio output connector of the digital disk recorder to the audio input connector of this monitor with an audio cable. I PC connection Connect the video output (analog RGB) of a PC to the PC input connector of this monitor. The length of a PC cable shall be 3 m or less.
• Press the reset switch to restart this monitor. • Check the cables are properly inserted into the connectors. When the power indicator lights orange, the ECO mode is active.
Page 24
Problem Inspect the power cord and power plug occasionally. The power cord, connectors, or power plug is partly hot during use. The power cord gets hot when bent or stretched. Cause · Remedy • The power cord, connectors, or power plug is damaged. Continued use of the damaged power cord, connectors, or power plug may cause electric shock or fire.
463 mm (W) x 321 mm (H) x 78 mm (D) {18-7/32" (W) x 12-5/8" mm (H) x 3-1/16" (D)} (monitor stand excluded) WV-LW2200: 531 mm (W) x 414 mm (H) x 235 mm (D) {20-29/32" (W) x 16-5/16" (H) x 9-1/4" mm (D)} (monitor stand included) 531 mm (W) x 361 mm (H) x 78 mm (D) {20-29/32"...