Related Manuals for Panasonic HMe Series
Summary of Contents for Panasonic HMe Series
- Page 1 Touch Terminals HMe Series Instruction Manual ACGM0195V5EN Version 5.0 2023.01 https://industry.panasonic.eu...
- Page 2 This manual and everything described in it are copyrighted. You may not copy this manual, in whole or part, without written consent of Panasonic. Please direct support matters and technical questions to your local Panasonic representative. Distributed by Panasonic Industry Europe GmbH https://industry.panasonic.eu...
-
Page 3: Table Of Contents
Table of contents Introduction ............................... 4 Important symbols ............................ 4 Special instructions for use ........................5 Standards and approvals ......................... 5 Product overview ............................6 Product identification ..........................6 Technical data common to all models ..................... 7 Hardware specifications ........................7 Environmental conditions ........................ -
Page 4: Introduction
Introduction Introduction This instruction manual contains information about the installation, transportation, storage, assembly, use and maintenance of touch terminals of the HMe series. The following models are available: HMe04 Touch terminal with TFT color 4.3” widescreen display touchscreen HMe07 Touch terminal with TFT color 7” widescreen display touchscreen HMe10 Touch terminal with TFT color 10.1”... -
Page 5: Special Instructions For Use
Special instructions for use Special instructions for use • The product shall only be used in an area of not more than pollution degree 2, as defined in IEC/EN 60664-1. • The product shall be installed in an enclosure that provides a degree of protection not less than IP54 in accordance with IEC/EN 60079-7. -
Page 6: Product Overview
They are the ideal choice for all demanding HMI applications including factory and building automation. The HMe series touch terminals have been designed to run the software HMWIN Studio. • Compatible with HMWIN Studio. • Full vector graphic support. Native support of SVG graphic objects, transparency and alpha blending. -
Page 7: Technical Data Common To All Models
Technical data common to all models Technical data common to all models Hardware specifications Touchscreen technology Resistive Real-time clock back-up Supercapacitor Fuse Automatic Serial port RS232, RS485, RS422 software configurable Recipe memory Flash Real-time clock Clock/calendar with supercapacitor back-up Accuracy real-time clock (at 25°C) <100ppm Environmental conditions Operating temperature... -
Page 8: Electromagnetic Compatibility (Emc)
Technical data common to all models Electromagnetic compatibility (EMC) Radiated disturbance test Class A EN 55011 8kV (air electrostatic discharge) Electrostatic discharge immunity EN 61000-4-2 test 4kV (contact electrostatic discharge) 80MHz–1GHz, 10V/m Radiated, radio frequency, 1.4–2GHz, 3V/m EN 61000-4-3 electromagnetic field immunity test 2–2.7GHz, 1V/m ±2kV DC power port Burst immunity test... -
Page 9: Viewing Angles
Technical data common to all models Viewing angles The viewing angles for the horizontal (L, R) and vertical (U, D) axes are specified in reference to the vertical axis of the display. The viewing angles always refer to the standard mounting orientation. For the viewing angle values (U, D ,L, R), refer to the technical data of the respective touch terminal model. -
Page 10: Technical Data By Model
Technical data by model Technical data by model HMe04 HMe07 HMe10 Display / Backlight TFT color / LED Colors Resolution (pixel) 480 x 272 800 x 480 1024 x 600 Brightness 200cd/m² typ. Display size (inch) 4.3” widescreen 7” widescreen 10.1”... -
Page 11: Product Dimensions
Product dimensions Product dimensions HMe04 Cutout 136mm 96mm 147mm 107mm 29mm ACGM0195V5EN Version 5.0... -
Page 12: Hme07
Product dimensions HMe07 Cutout 176mm 136mm 187mm 147mm 29mm ACGM0195V5EN Version 5.0... -
Page 13: Hme10
Product dimensions HMe10 Cutout 271mm 186mm 282mm 197mm 29mm ACGM0195V5EN Version 5.0... -
Page 14: Unpacking And Packing Instructions
Unpacking and packing instructions 10. Unpacking and packing instructions HMe04, HMe07 HMe10 To repack the product, please follow the instructions backwards. ACGM0195V5EN Version 5.0... -
Page 15: Installation
Installation 11. Installation 11.1 Installation environment The product is not intended for continuous exposure to direct sunlight. This might accelerate the aging process of the front panel film. The product is not intended for installation in contact with corrosive chemical compounds. Check the resistance of the front panel film to a specific compound before installation. -
Page 16: Installation Procedure
Installation 11.2 Installation procedure For details on installation, please refer to the “Installation Guide” provided with the product. Place the fixing brackets contained in the fixing kit as shown in the following figure. Notice Make sure to screw each fixing screw until the bezel corner gets in contact with the panel. Tightening torque: 75Ncm ACGM0195V5EN Version 5.0... -
Page 17: Connections
Connections 12. Connections 12.1 HMe04 (1) Serial port (2) Ethernet port (3) USB port (4) Power supply 12.2 HMe07 Serial port Ethernet port USB port Power supply ACGM0195V5EN Version 5.0... -
Page 18: Hme10
Connections 12.3 HMe10 (1) Serial port (2) Ethernet port (3) USB port (4) Power supply ACGM0195V5EN Version 5.0... -
Page 19: Serial Port
Connections 12.4 Serial port The serial port is used to communicate with the PLC or with another type of controller. Standards available for the signals in the PLC port connector are: RS232, RS422, RS485. Use the corresponding communication cable for the connection. The serial port is software programmable. -
Page 20: Power Supply, Grounding, And Shielding
Connections 12.6 Power supply, grounding, and shielding The power supply terminal block is shown in the following figure. DC power connector - AWG24 wire size - R/C terminal blocks (XCFR2), female pitch 5.08mm, torque 4.5lb-in 3 conductors, minimum 1.5mm² wire diameter, minimum temperature conductor rating 105°C NOTE Make sure that the power supply has sufficient power capacity for the operation of the product. -
Page 21: Getting Started
Getting started 13. Getting started The HMe series touch terminals must be programmed with the programming software HMWIN Studio (starting from v2.6), a Windows application. There are two options to transfer an HMWIN application project to a touch terminal: Ethernet Connect the touch terminal via the Ethernet interface to a personal computer running the HMWIN Studio software. -
Page 22: Touchscreen Calibration
Touchscreen calibration 14. Touchscreen calibration The HMe series touch terminals support the calibration of the interface. To start calibration do the following: • Tap on the surface of the touchscreen during the power-up phase of the device. The tapping frequency must be high. Start tapping the touchscreen as soon as power has been supplied to the touch terminal. -
Page 23: Record Of Changes
Record of changes 16. Record of changes ACGM0195V5EN, January 2023 • Deleted the chapter “System settings tool” • Added the chapters “Special instructions for use” and “Disposal” • Updated the chapter “Standards and approvals” • Updated company name and back page •... - Page 24 Panasonic Industry Europe GmbH Caroline-Herschel-Strasse 100, 85521 Ottobrunn, Germany +49 89 45354-1000 https://industry.panasonic.eu January, 2023...