Table of Contents Hardware Installation and Connection ................1 1.1 Check Unpacked NVR ..................1 1.2 About Front Panel and Rear Panel ..............1 1.3 After Remove the Chassis ..................1 1.4 HDD Installation ..................... 1 1.5 Front Panel ......................2 1.6 Rear Panel ......................
Page 3
Welcome Thank you for purchasing our network disk recorder! This quick start guide is designed to be a reference tool for your system.
Page 4
Important Safeguards and Warnings 1.Electrical safety All installation and operation here should conform to your local electrical safety codes. The product must be grounded to reduce the risk of electric shock. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.
1 Hardware Installation and Connection Note: All the installation and operations here should conform to your local electric safety rules. 1.1 Check Unpacked NVR When you receive the NVR from the forwarding agent, please check whether there is any visible damage.
4. After connect the cable, put the front cover back to the device and then fix screws of the rear panel in the chassis. 1.5 Front Panel For detailed operation instruction, please refer to the User’s Manual included in the resources CD. The front panel is shown as in Figure 1-1.
Page 7
Name Icon Function playback/8 normal playback. Play Next /0 When playback, click it to view the next record. │ Play previous/9 │ When playback, click it to view the previous record. It is to display system is recording or not Record 1~16 indicator light...
1.6 Rear Panel The K-NL316K/G rear panel is shown as below. See Figure 1-2. Figure 1-2 Please refer to the following sheet for detailed information. Name Function Power switch Power on-off button Power input Input AC 100~240V. port MIC IN Audio input port Bidirectional talk input port.
Page 9
Name Function port RS485_B.It is the cable B. You can connect to the control devices such as speed dome PTZ. CTRL 12V Controller 12V power output. It is to control the on- off alarm relay output. It can be used to control the device alarm output.
3 GUI Operation Connect the device to the monitor and then connect a mouse and power cable. Click the power button at the rear panel and then boot up the device to view the video output. You can use the mouse to implement some GUI operation.
Important: For security reason, please modify password after you first login. Within 30 minutes, three times login failure will result in system alarm and five times login failure will result in account lock! 3.2 Remote Device From Main menu->SETTING->REMOTE->REMOTE device or right click mouse on the preview interface and then select remote device item, you can see the following interface.
Page 13
Click Manual Add button, you can add a device directly. See Figure 3-6. Important Please note the manual add function is for Panasonic, the others and custom. When the type is the custom, you can just input URL address, username and password connect to the network camera without considering network camera manufacture.
3.3 Schedule Note: You need to have proper rights to implement the following operations. Please make sure the HDDs have been properly installed. After the system booted up, it is in default 24-hour regular mode. You can set record type and time in schedule interface.
Page 15
Figure 3-7 Set record type. See Figure 3-8. Figure 3-8 Please draw manually to set record period. There are six periods in one day. See Figure 3-9. Figure 3-9 Please check the box to select the corresponding function. After completing all the setups please click save button, system goes back to the previous menu.
3.4 Realtime Playback Preview control interface Move you mouse to the top center of the video of current channel, you can see system pops up the preview control interface. See Figure 3-12. If your mouse stays in this area for more than 6 seconds and has no operation, the control bar automatically hides.
4 Web Operation This series NVR product support the Web access and management via PC. Web includes several modules: Monitor channel preview, record search, alarm setup, system configuration, PTZ control, monitor window and etc. 4.1 Network Connection Before web client operation, please check the following items: Network connection is right ...
If it is your second time to insert the PoE, system can check the saved MAC address according to <Channel>---<IPC mac> map to make sure current IPC has connected or not. If system finds the previous information and the channel is idle, system can map it to the previously used channel.
4.3 Main Window 4.3.1 LAN Login For the LAN mode, after you logged in, you can see the main window. See Figure 4-2. Click the channel name on the left side; you can view the real-time video. Figure 4-2 4.3.2 WAN Login In WAN mode, after you logged in, the interface is shown as below.
Page 21
Note For detailed operation introduction, please refer to our resource CD included in your package for electronic version of the User’s Manual. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice. ...