Page 4
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards. 1.1.1. Leakage Current Cold Check 1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2.
Page 5
milliamp. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer. 2. Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity.
Page 6
installed. Caution Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
Page 7
Suggested Pb free solder There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used. 4. Input signal that can be displayed *Mark:Applicable input signal for Component(Y,P )and HDMI Horizontal...
Page 8
display. 5. Self-check function When phenomena like "the power fails from time to time" or "the video/audio fails from time to time" can not be confirmed at the time of servicing, the self-check function can be used to confirm the occurrence and to limit the scope for the defective circuits.Also, when "the power fails from time to time", display on the screen can be used to confirm the occurrence and to limit the scope for the defective circuits.
Page 9
Board Name Function A-Board Main (AV connector, AV Switch, Tuner, Audio & Video Processor, MCU, LCD Driver, LVDS) V-Board Remote Receiver, LED, B.A.T.S. G-Board AV3,Headphone jack AP-Board Power Supply, Power Regulator Power Unit Power (AC/DC) None serviceable. Power Unit should be exchanged for service. Control Panel Unit None serviceable.
Page 10
4. Remove the fixing screws (4 pcs). 5. Remove the pedestal ass’y. 7.2. Rear cover...
Page 11
1. Remove the fixing screws (12 pcs for 26" or 14 pcs for 32" and 3 pcs). 2. Remove the rear cover. 7.3. Rear Support MTG (Left and right) 1. Remove the rear cover. (See 7.2) 2. Remove the fixing screws (4 pcs). 3.
Page 12
7.4. AC cord AC cord (26") 1. Remove the rear cover (See 7.2) and the rear support MTG. (See 7.3) 2. Take out the groove of the AC cord from the slot of the Tuner cover. 3. Disconnect the couplers of AC cord.
Page 13
AC cord (32") 1. Remove the rear cover (See 7.2) and the rear support MTG. (See 7.3) 2. Take out the groove of the AC cord from the slot of the Tuner cover. 3. Unlock the cable clamper. 4. Disconnect the couplers of AC cord.
Page 14
7.5. Tuner Cover Ass’y 1. Remove the rear cover (See 7.2) and the rear support MTG. (See 7.3) 2. Remove the fixing screws (2 pcs). 3. Remove the Tuner Cover Ass’y. 7.6. Power Button Bracket Ass’y...
Page 15
1. Remove the rear cover (See 7.2) and the rear support MTG. (See 7.3) 2. Remove the fixing screws (2 pcs). 3. Remove the Power Button Bracket Ass’y. 7.7. Control Panel Ass’y 1. Remove the Power Button Bracket Ass’y. (See 7.5) 2.
Page 16
7.8. Power Supply unit 1. Disconnect the couplers (P301~AP2 and P302~AP1). 2. Remove the fixing screws (5 pcs). 3. Remove the Power Supply unit. 7.9. A-Board 1. Remove the Tuner Cover Ass’y. (See 7.5) 2. Remove the fixing screws (11 pcs). 3.
Page 17
Fix the A shield case to A-Board as follow: Caution Fix carefully shield case to shield clip (ZA4001-ZA4008, and ZA4030). 7.10. AP-Board 1. Disconnnect the couplers (AP1-AP6). 2. Remove the fixing screws (4 pcs). 3. Remove the AP-Board.
Page 18
7.11. G-Board G-Board (26") 1. Remove the Rear Cover. (See 7.2) 2. Disconnect the couplers (G1 and G2). 3. Remove the fixing screws (2 pcs). 4. Remove the G-Board Ass’y. 5. Remove the fixing screws (2 pcs). 6. Remove the G-Board.
Page 19
7. Remove the fixing screws (2 pcs). 8. Remove the Shield case. G-Board (32") 1. Remove the Rear Cover. (See 7.2) 2. Disconnect the couplers (G1 and G2). 3. Remove the fixing screws (2 pcs). 4. Remove the G-Board Ass’y.
Page 20
5. Remove the fixing screws (2 pcs). 6. Remove the G-Board. 7. Remove the fixing screws (2 pcs). 8. Remove the Shield case.
Page 21
7.12. V-Board and Led Panel 1. Remove the fixing screws (2 pcs). 2. Disconnect the couplers (V1). 3. Remove the V-Board. 7.13. Speaker 1. Remove the fixing screws (8 pcs).
Page 22
2. Remove the Speakers (left and right). 7.14. Main chassia Ass’y 1. Remove the fixing screws (3 pcs). 2. Disconnect the couplers. 3. Remove the Main Chassia Ass’y. 7.15. LCD Panel LCD Panel (26")
Page 23
1. Remove the Main Chassis Ass’y. (See 7.13) 2. Remove the fixing screws (7 pcs). 3. Remove the LCD mount MTG (top, bottom, left, right). 4. Disconnect the couplers. 5. Remove the LCD Panel. LCD Panel (32") 1. Remove the Main Chassis Ass’y. (See 7.13) 2.
Page 24
8. Location of Lead Wiring Location of Lead Wiring (26") Location of Lead Wiring (32")
Page 26
10. Service Mode Function MPU controls the functions switching for each IC through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Mode. 10.1. How to enter SERVICE 1 1. Set OFF TIMER to 15,30..2.
Page 29
10.4. Option Code Setting If the memory IC (IC1102) or A Board is replaced, option code should be re-memorized. Spare part of IC1102 is already memorized all Data. If you use for other model, you should re-memorized the different option code in SERVICE 2 mode.
Page 30
11. Adjustment 11.1. Voltage chart of A board 11.2. Voltage chart of AP board 11.3. DVCO adjustment...
Page 49
TX-26LX60A/M/X, TX-32LX60A/M/X Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks C1168 ECJ1XB1C104K C 0.1UF, Z, 16V C901 ECJ2FB1H104K C 0.1UF, K, 50V C1181 ECJ0EB1H102K C 1000PF, K, 50V C902 ECJ2FB1H104K C 0.1UF, K, 50V C1182 ECJ0EB1H102K C 1000PF, K, 50V C903...
Page 50
TX-26LX60A/M/X, TX-32LX60A/M/X Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks C2181 ECJ1VB1C224K C 0.22UF, K, 16V C4057 F1J0J1060004 C 0.010UF, K, 16V C2223 EEEHB1E101P 100PF, J, 25V C4058 ECJ0EB1A104K C 0.1UF, K, 10V C2367 EEEHB1C101UP C 100PF, J, 16V...
Page 51
TX-26LX60A/M/X, TX-32LX60A/M/X Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks C4808 ECJ1XB1C104K C 0.1UF, Z, 16V D1811 MA111 DIODE C5001 ECJ0EB1A104K C 0.1UF, K, 10V D1812 MA8220-M ZENER DIODE C5002 ECJ0EB1A104K C 0.1UF, K, 10V D1813 MA111...
Page 54
TX-26LX60A/M/X, TX-32LX60A/M/X Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks R1826 ERJ3GEYJ103 M 10KOHM,J,1/16W R3029 ERJ3EKF1002 M 10KOHM, 1/16W R1827 D0GB472JA041 M 4.7K OHM J 1/16W R3031 ERJ3EKF2200 M 220 OHM, 1/16W R1828 D0GB472JA041 M 4.7K OHM J 1/16W R3032...
Page 55
TX-26LX60A/M/X, TX-32LX60A/M/X Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks R3233 D0GB473JA041 M 47K OHM J 1/16W R4065 D0GB220JA041 M 22 OHM J 1/16W R3234 D0GB222JA041 M 2.2K OHM J 1/16W R4066 D0GB101JA041 M 100 OHM J 1/16W R3235 D0GB152JA041 M 1.5K OHM J 1/16W...
Page 56
TX-26LX60A/M/X, TX-32LX60A/M/X Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks R4202 ERJ3EKF1000 M 100 OHM, 1/16W R4754 ERJ2GE0R00 M 0.0 OHM, J,0.063W R4203 D0GB102JA041 M 1K OHM J 1/16W R4755 ERJ2GE0R00 M 0.0 OHM, J,0.063W R4204 ERJ3EKF1600 M 160 OHM, 1/16W...
Page 57
CIRCUIT BOARD A TX-26LX60A TXN/A10MBM CIRCUIT BOARD A TX-26LX60M TXN/A10MEM CIRCUIT BOARD A TX-26LX60X TXN/A10MXJ CIRCUIT BOARD A TX-32LX60A TXN/A10MAM CIRCUIT BOARD A TX-32LX60M TXN/A10MDM CIRCUIT BOARD A TX-32LX60X LSEP1221A1HB P MODULE 1 PRT-10...
Page 58
K2CT2YY00002 AC POWER CORD TX-26LX60M/X K2DR53D00001 AC PLUG ADAPTER 1 TX-26LX60X,TX-32LX60X K2CJ2YY00003 AC POWER CORD TX-32LX60A K2CT2YY00004 AC POWER CORD 1 TX-32LX60M/X L5EDD6Q00013 LCD PANEL TX-26LX60A/M/X L5EDD8Q00019 LCD PANEL TX-32LX60A/M/X N2QAJB000121 REMOTE CONTROL TRANSMITT TBLA0194 STAND ASS'Y...
Page 93
AUDIO VCC 13.5V POWER CONTROLLER UNIT MAIN 5V MAIN 1.8V AC IN ST7V RELAY7V KEY CONTROL POWER SUPPLY INV_ON INV_SOS IC1102 KIDO_PWM 3.3V 1.8V ST7V EEPROM FACT5V AUDIO_VCC BT30V IC4001 PANEL_5V TU101 TV_V RF in Tuner Jk3001 MOUT Y/Pb/Pr,V,L/R Y,Pb,Pr IC4004 V,L/R,Y/C VCTP...
Page 94
KEY-UNIT AP-BOARD P-BOARD A-BOARD JTAG EEPROM FPGA G-BOARD VCTP A9 FPGA HEADPHONES HEADPHONE JACK AMP. TV SOUND POWER HDMI AMPLIFIER V-BOARD LED,BATS SPEAKER R SPEAKER L TX-26/32LX60A/M/X TX-26/32LX60A/M/X P.C.B. BLOCK DIAGRAM P.C.B. BLOCK DIAGRAM...