Page 1
SAIN3 LLC DUAL BAND FM Transceiver UV-5R PERATING ANUAL FCC ID: 2AN62-UV5R...
Page 2
PREFACE Thank you for purchasing UV-5R Amateur Portable Radio, which is a dual band/dual display radio. This easy-to-use radio will deliver you secure, instant and reliable communications at peak efficiency. Please read this manual carefully before use. The information presented herein will help...
Page 3
CONTENT 1.-SAFETY INFORMATION 2.-FEATURES AND FUNCTIONS 3.-UNPACKING AND CHECKING EQUIPMENTS 4.- OPTIONAL ACCESSORIES 5.- INSTALLATION OF ACCESSORIES 5.1.- INSTALLING THE ANTENNA 5.2.- INSTALLING THE BELT CLIP 5.3.- MICRO-HEADSET INSTALLATION OF EXTERNAL 5.4. – BATTERY INSTALLATION 6.-BATTERY CHARGING 7.-BATTERY INFORMATION 7.1.-INITIAL USE 7.2.-BATTERY TIPS 7.3.-PROLONG BATTERY LIFE 7.4.-BATTERY STORAGE...
12.2.-SHORTCUT MENU OPERATION 12.3. -“SQL” (SQUELCH) 12.4.-FUNCTION “VOX” (VOICE OPERATED TRANSMISSION) 12.5.- SELECT WIDEBAND OR NARROW BAND “W/N” 12.6.-TDR (DUAL WATCH/DUAL RECEPTION) 12.7.- TOT(TRANSMISSION TIMER) 12.8.-CTCSS/DCS 12.9.- ANI 12.10.- DTMFST (DTMF TONE OF TRANSMITTING CODE ) 12.11.- SC-REV(SCAN RESUME METHOD) 12.12.- PTT-ID(PTT OR RELEASE PTT TO TRANSMIT THE SIGNAL CODE) 12.13-BCL(BUSY CHANNEL LOCKOUT) 12.14.- SFT-D(DIRECTION OF FREQUENCY SHIFT)
1.-SAFETY INFORMATION: The following safety precautions shall always be observed during operation, service and repair of this equipment. ◇ This equipment shall be serviced by qualified technicians only. ◇ Do not modify the radio for any reason. ◇ Use only SAIN3 LLC supplied or approved batteries and chargers. ◇...
4.- OPTIONAL ACCESSORIES: Note: - Consult the dealer or retailer for information about options available. 5.- INSTALLATION OF ACCESSORIES: 5.1.- INSTALLING THE ANTENNA: Install the antenna as shown in the figure below and turn it clockwise until it stops. Note: - When installing the antenna, don’t rotate it by its top, holding it by its base and turn.
Plug the external micro-headset connector into the jack of ‘SP. & MIC’ of the transceiver as shown in the figure below. 5.4. – BATTERY INSTALLATION: -When attaching the battery, make sure the battery is in parallel and in good contact with the aluminum chassis.
6.-BATTERY CHARGING: Use only the charger specified by the manufacturer. The charger’s LED indicates the charging progress. CHARGING STATUS LED INDICATION Standby (no-load) Red LED flashes,while Green LED glows Charging Red LED solidly glows Fully Charged Green LED solidly glows Error Red LED flashes,while Green LED glows Please follow these steps:...
7.2.-BATTERY TIPS: 1. When charging your battery, keep it at a temperature among 5℃ - 40℃. Temperature out of the limit may cause battery leakage or damage. 2. When charging a battery attached to a radio, turn the radio off to ensure a full charge. 3.
-While setting the RX CTCSS/DCS, press the key 【*SCAN】to scan the RX CTCSS/DCS. KEY: -Under channel mode, press key to switch High/Low transmit power. -Press key for 2 seconds to lock/unlock the keypad. -FUNCTION KEYPAD: -【MENU】key: -To enter the menu of the radio and confirm the setting. -【▲】【▼】key: -Press and hold 【▲】or 【▼】key for frequency up or down fast.
‘DCS’ activated. Frequency offset direction for accessing repeaters. Dual Watch/Dual Reception functions activated. Function ‘VOX’ enabled. Reverse function activated. Wide Band selected. Battery Level indicator Keypad lock function activated. Low transmit power. Operation frequency. ▲▼ Signal Strength Level. 10.- 1750 Hz TONE FOR ACCESS TO REPEATERS: The user needs to establish long distance communications through an amateur radio repeater which is activated after receiving a 1750 Hz tone.
12.2.-SHORTCUT MENU OPERATION: 1.-Press the key MENU,then press the key ▲ or ▼ to select the desired menu. 2.-Press the key MENU again, come to the parameter setting. 3.-Press the key ▲ or ▼ to select the desired parameter. 4.-Press the key MENU to confirm and save, press the key EXIT to cancel setting or clear the input. -Note: Under channel mode,the following menu settings are invalid:CTCSS,DCS,W/N,PTT-ID,BCL,SCAN ADD TO,S-CODE,CHANNEL NAME.Only the H/L power could be changed.
This feature allows you to operate between frequency A and frequency B. Periodically, the transceiver checks whether a signal is received on another frequency that we have scheduled. If you receive a signal, the unit will remain in the frequency until the received signal disappears. 12.7.- TOT(TRANSMISSION TIMER): This function can automatically control the time we transmit each time you press [PTT] on the transceiver.
12.11.- SC-REV(SCAN RESUME METHOD): This transceiver allows you to scan memory channels, all the bands or part of the bands. When the transceiver detects a communication, the scan will stop automatically. Notes: - "TO" (Time Operation): Scanning will stop when it detects an active signal. The scanning will stop on each channel or active frequency for a predetermined time, after that time the scan will resume automatically.
12.16.-STE (TAIL TONE ELIMATION): This function is used to activate or deactivate the transmission end of the transceiver. this final tone transmission only be used in communications between transceivers and not in communications through a repeater, which must be deactivated. 13.-CTCSS TABLE: Nº...
Page 19
15.-TECHNICAL SPECIFICATION: 15.1.-GENERAL: Frequency range: Rx:136MHz-174MHz / 400MHz-480MHz Tx:144MHz-148MHz / 420MHz-450MHz Memory channels: Up to 128 channels Frequency stability: 2.5ppm. Frequency step: 2.5kHz/5kHz/6.25kHz/10kHz/12.5kHz/25kHz. 50Ω . Antenna impedance: Operating temperature: -20 ° C to +60 ° C. Supply voltage: Rechargeable Lithium-Ion mAh 7.4V/1800. Consumption in standby: Consumption in reception: 380mA...
Page 20
16.-TROUBLESHOOTING: Problem Possible cause / solution The radio does not start. The battery is low, replace the battery with a charged battery or proceed to the battery. The battery is not installed correctly, remove the battery and reattach it. The battery runs down quickly. The battery life has come to an end, replace the battery with a new one.
17.-WARRANTY: (Better buy the radios from local dealer). WARRANTY CERTIFICATE Brand: Model no.: Serial no.: Name of purchaser: Address: City: Zip code: Province/State: Tel no.: Seal and name of the dealer: Date of purchase: WARNING: Warranty is valid provided it is complete and properly filled in legibly and clearly present the seal and name of the dealer and have attached the bill proof of purchase of equipment.
Page 22
The warranty does not cover any faults caused by accident, improper installation and use, electric shock (eg storms), connect a power other than that specified, reverse polarity in the diet, or claims due to deterioration in the external appearance of normal use, nor the amount or condition of the accessories. Checking the accessories is the responsibility of the purchaser at the time of purchasing the device.