Copyright 2006 InnoLux Tech. Corp. Ltd All Rights Reserved This manual may not, in whole or in part, be copied, Photocopied, reproduced, translated, or converted to any electronic or machine readable form without prior written permission of InnoLux Tech. Corp. Ltd. Acer D240H Service Manual...
Acer Acer –LCD-D240H Important Safety Notice Safety precautions This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However, improper used or installation may cause damage to the monitor as well as to the user.
01 Product Specification General: Acer D240H is designed with LVDS interface and VGA/DVI-D/HDMI input, and Embedded DPF Function ,it featured with embedded universal AC power supplies and audio input. It’s a green product and meets all ROHS standard. The power button and display control buttons are on the front of the monitor.
Page 5
Acer Acer –LCD-D240H USB: USB2.0 (optional function) Webcam: 1.0M resolution(1280 x 800), standard USB2.0 interface, array microphone (optional function) Operation Specifications The unit should suffer no visible cosmetic damage and should operate with no degradation in display quality during exposure to the operating conditions and after exposure to the non-operating conditions, in any sequence.
Page 7
Acer Acer –LCD-D240H DC output loading Vcc5V/1.8A, capability Vcc25V/1.4A Audio 5V: 1.5A USB 5V: 1.5A Rise Time <50mS Dynamic load change Hold-up time AC input: 100V~240V >10mS Overshoot <10% Turn on delay time Power management See Table-1 Note3: Paralleled a 0.1uF ceramic Cap. And 47uF aluminum Cap. Between the end of DC loading side, Measured band-width=20MHz.
Page 8
Acer Acer –LCD-D240H CCFL startup voltage ≧2000 Vrms (0˚C) CCFL startup voltage ≧1850 Vrms (25˚C) Operating frequency 40~60 KHz Protect delay time > 1 second Efficiency ≥75% Note: Other panels please refer to the reference panel specs. Brightness output The test to verify specifications in this section shall be performed under the following standard conditions unless otherwise noted.
Page 9
Acer Acer –LCD-D240H Min. luminance nine points (backlight ≥ 75 Max. luminance nine points (backlight Input / Output Signal Specifications 4.1 AC in AC Input Voltage: 100~240VAC 4.1.1 AC Input Current: 1.2A @100Vac, 0.6A @240Vac 4.1.2 AC Frequency Range: 50~60Hz 4.1.3...
Page 10
Acer Acer –LCD-D240H 4.5 DVI-D in DVI-D Connector Pin assignment: Symbol Symbol TMDS Data 2- Hot Plug Detect TMDS Data 2+ TMDS Data 0- TMDS Data 2/4 shield TMDS Data 0+ TMDS Data 0/5 shield DDC Clock DDC Data Clock shield...
Page 11
Acer Acer –LCD-D240H DDC SCL Signal SPEC: 4.6.2 Items Condition Specification Analog RGB signal Input impedance =75 Ohm 0.7Vp-p Sync Input impedance ≧1k Ohm TTL level, Separate H/V-sync(+/-) H-Sync Frequency 31K~83KHz V-Sync Frequency 49~76Hz 4.7 Timing table VESA MODES Horizontal...
Page 12
Acer Acer –LCD-D240H SVGA 832*624@75Hz 49.725 74.55 57.283 1152*870@75Hz 68.681 75.062 Other MODES WXGA 1280*800@60Hz 49.702 59.81 83.5 Note: 1. Non-interlace signals only (An interlace signal cannot be display) 2. Please refer to F/W specification for more detail 3. Each frequency of Power Macintosh and Sun Ultra is a reference value...
Page 13
Acer Acer –LCD-D240H 4.8 HDMI timing table For DVD Player Input, Attached timing is supported : Ratio Mode Resolution Pixel Clock MHz H sync KHz V sync Hz 640 x 480p 25.2 31.5 NTSC (480i) 720 x 480 13.50 15.73...
Page 14
0A D0 8A 4.11 DPF function D240H supports DPF Function, which Embeded 2G Nandflash stroage ,it can also communication with PC by connecting USB cable,and supports 4 IN 1 memory card which includes SD, XD, MS, and MMC, besides the 4 kind’s memory card,it also...
Page 15
2) card reader function Connect the USB upstream and the card read function will be started when D240H on Monitor mode..PC will find the two USB devices are CF card and SD/MS/XD/MMC card, the two devices that in the DPF all can be operation by PC 4.11.2.
Page 16
Acer Acer –LCD-D240H 4.11.4. DPF function test 4.11.4.1. DPF Monitor Category Yes/ No keypad control flow .jpg 1. Switch to DPF Photo keypad flow .bmp 2. DPF play photo mode keypad flow...
Page 19
Acer Acer –LCD-D240H Setting menu layer-1...
Page 20
Acer Acer –LCD-D240H Setting menu layer-2 Setting menu layer-3...
Page 21
Acer Acer –LCD-D240H 4.11.4.2. DPF photo function test 1.Test the picture as below items: 1).Photo performance 2). Next picture 3). Forward picture 4). Pause 5). Play 6), slide show. 7). Rotate. 8). Browser small and big photo Check and confirm the function is OK! 2.Test the setting menu as below items:...
Page 22
4). If first Monitor mode switch to DPF when AC on and DC on and form power saving ,the screen will display DPF Acer logo 5). If hot_plug any card on DPF mode,the display screen will change to input source select mode .
Page 24
Acer Acer –LCD-D240H Function Specifications All the tests to verify specifications in this section shall be performed under the following standard conditions unless otherwise noted. The standard conditions are: Temperature : 25 ± 5°C Warm-up time : 30 minutes minimum...
Page 25
Acer Acer –LCD-D240H Function Specifications All the tests to verify specifications in this section shall be performed under the following standard conditions unless otherwise noted. The standard conditions are: Temperature : 25 ± 5°C Warm-up time : 30 minutes minimum...
Page 26
Acer Acer –LCD-D240H Text mode Standard mode Graphics mode Movie mode User mode Text mode 0~100 Contrast Standard mode Graphics mode Movie mode 0~100 H. Position 0~100 V. Position 0~100 Focus 0~100 Clock 50 (1) Warm Cool Color Temp 0~100 User 0~100...
Page 27
Acer Acer –LCD-D240H Reset Resolution H. Freq V. Freq Input Type Notes: (1) Clock default 50 is for Visa timing. Others depend on timing. (2) Depend on timing & S/N...
Page 28
Acer Acer –LCD-D240H 5.4 OSD Translation 5.4.1 Monitor part Main menu (NO_EMEA) English Deutsch Français Español Italiano 繁體中文 简体中文 日本語 (英语) (德语) (法语) (西班牙语) (意大利语) Picture Bild Image Imagen Immagine 畫面 画面 ピクチャー Brightness Helligkeit Luminosité Brillo Luminosità 亮度 亮度...
Page 29
Acer Acer –LCD-D240H Message menu: (NON_EMEA) English Deutsch Français Español Italiano 繁體中文 简体中文 日本語 (英语) (德语) (法语) (西班牙语) (意大利语) Autoréglage Autoajuste Auto Config 自動調整 Autom. Abgl. Autoregolazione 自动调整 自動調整 Veuillez Espere, Please Wait Bitte warten Attendere prego 請稍待 请稍待 お待ちください...
Page 30
English Russian Deutsch Français Español Italiano Dutch Finnish (英语) (俄语) (德语) (法语) (西班牙语) (意大利语) (荷兰语) (芬兰语) Acer Acer –LCD-D240H Picture Изображ. Bild Image Imagen Immagine Beeld Kuva Brightness Яркость Helligkeit Luminosité Brillo Luminosità Helderheid Kirkkaus Контрастно Contrast Kontrast Contraste Contraste...
Page 31
Acer Acer –LCD-D240H Standard Standard Standard Estándar Standard 標準 标准 標準 Text Text Texte Texto Testo 文字 文本 テキスト グラフィック Graphics Grafiken Images Gráficos Grafica 圖形 图形 ス Movie Spielfilm Film Película Film 電影 电影 ムービー User Benutzer Utilisateur Usuario Utente 使用者...
Page 32
Acer Acer –LCD-D240H Monitor Weight 5.6±0.3Kg 6.2 Cabinet Material Cabinet Material Spec Cabinet Plastic Material ABS HB(PMMA) BLACK Front Bezel Back Cover BLACK Base BLACK Cabinet Texture ACER SPECIFICATION 6.3 Mechanical Specification Mechanical Spec Bezel Gap Specification ≦1.3mm Screen printed Parts Front bezel 6.4 Base Mechanical Interface...
Page 33
Acer Acer –LCD-D240H 7. Package 7.1 Unit Package Specification 7.1.1 Units package Items Spec Packaging Refer to ME PACKING SPEC COLOR Length 632+/-2.0mm Height 494+/-2.0mm Width 139+/-2.0mm Gross Weight 7.9±0.3kg Units per Pallet 56sets/pallet 40’ /20’ Container Loading, Palletized 1120sets/560sets 7.1.2 Unit Packing Vibration...
Page 34
Acer Acer –LCD-D240H Test 7.1.3 Non operation Thermal Shock Item Description Temperature C to 60 >60 (10hrs)>25 (2hrs)>-20 (10hrs)>25 ºC ºC ºC ºC ºC Reset cycles times every transition time 0.5 hr, 3cycles , Total cycles 3 cycles 7.1.4 Package Drop...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 1.0 Handling Precautions Since front polarizer is easily damaged, pay attention not to scratch it. Be sure to turn off power supply when inserting or disconnecting from input connector. Wipe off water drop immediately. Long contact with water may cause discoloration or spots. When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 2.0 General Description This specification applies to the 24 inch-wide Color a-Si TFT-LCD Module M240HW01.The display supports the Full HD - 1920(H) x 1080(V) screen format and 16.7M colors (RGB 6-bits + Hi-FRC data). All input signals are 2-channel LVDS interface and this module doesn’t contain an inverter board for backlight.
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25℃: Item Unit Conditions Min. Typ. Max. Note Horizontal (Right) CR = 10 (Left) Viewing Angle [degree] Vertical (Up) CR = 10 (Down) Contrast ratio Normal Direction...
Page 41
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION Note 1: Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring (at surface 35 ) ℃ . In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and dark room.
Page 42
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION Note 3: Contrast ratio is measured by TOPCON SR-3 Note 4: Definition of Response time measured by Westar TRD-100A The output signals of photo detector are measured when the input signals are changed from “Full Black”...
Page 43
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION CT = | YB – YA | / YA × 100 (%) Where YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2) Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3 R G B R G B Gray Level = L127...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 3.0 Functional Block Diagram The following diagram shows the functional block of the 24.0 inch Color TFT-LCD Module: LVDS I/F PCB Interface: JAE FI-XB30SSL-HF15 STM MSBKT2407P30HB Mating Type: FI-X30HL (Locked Type) document version 1.0 NUMPAGES |29}...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 4.0 Absolute Maximum Ratings Absolute maximum ratings of the module are as following: 4.1 TFT LCD Module Item Symbol Unit Conditions Logic/LCD Drive [Volt] Note 1,2 Voltage 4.2 Backlight Unit Item Symbol Unit Conditions CCFL Current ICFL...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 5.0 Electrical characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Input power specifications are as following: Symbol Parameter Unit Conditions Logic/LCD Drive [Volt] +/-10% Voltage VDD= 5.0V,All black Pattern, IDD1 Input Current At 60Hz VDD= 5.0V,All black Pattern, PDD1 VDD Power...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when VDD is off. Please refer to specifications of SN75LVDS82DGG (Texas Instruments) in detail. Characteristics of each signal are as following: Symbol Parameter Units...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 5.2 Backlight Unit Parameter guideline for CCFL Inverter is under stable conditions at 25 (Room Temperature): ℃ Parameter Min. Typ. Max. Unit Note CCFL Standard Current (ISCFL) [mA] rms CCFL Operation Current (IRCFL) [mA] rms CCFL Frequency (FCFL) [KHz]...
Page 49
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION Note 2: CCFL standard current is measured at 25±2℃. Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter and TFT LCD. Note 4: The frequency range will not affect lamp life and reliability characteristics. Note 5: CCFL inverter should be able to release power that has generating capacity exceeding 2000 volt.
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 6.0 Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship of the input signals and LCD pixel format. 1919 1920 R G B R G B R G B R G B 1st Line R G B R G B R G B R G B...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 6.3 Signal Description The module using one LVDS receiver SN75LVDS82(Texas Instruments). LVDS is a differential signal technology for LCD interface and high speed data transfer device. LVDS transmitters shall be SN75LVDS83(negative edge sampling). The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels.
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION Note1: Start from left side Note2: Input signals of odd and even clock shall be the same timing. 6.4 Timing Characteristics Basically, interface timing described here is not actual input timing of LCD module but close to output timing of SN75LVDS82DGG (Texas Instruments) or equivalent.
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 6.5 Timing diagram M pixel Tblk(v) Tdisp(v) Invalid Data Invalid Data RGB Data Line Line Line Line Line Line Tclk Tdisp(h) Tblk(h) RGB Data Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 6.6 Power ON/OFF Sequence VDD power and lamp on/off sequence are as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. Value Parameter Unit...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 7.0 Connector & Pin Assignment Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. 7.1 TFT LCD Module Connector Name / Designation Interface Connector / Interface card Manufacturer...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 7.2 Backlight Unit Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation Lamp Connector / Backlight lamp Manufacturer CVILUX CP0502SL090...
Product Specification M240HW01 V2 AU OPTRONICS CORPORATION 9.0 Shipping Label The label is on the panel as shown below: Note 1: For Pb Free products, AUO will add for identification. Note 2: For RoHS compatible products, AUO will add for identification. Note 3: For China RoHS compatible products, AUO will add for identification.
07 Assembly and Disassembly Take out a panel Take out a chassis on the panel and assemble the power board and the chassis Assemble the panel and the bezel. Take out the main board and insert the FFC cable and keypad cable.
Page 76
Use a screwdriver to screw the 4 screws to Assemble the main board and the Card fix the main board and USB board. board with the chassis. MAIN BOARD Card BOARD S8: Use a screwdriver to screw the 1 Use a screwdriver to screw the 5 screws to screw to fix the HDMI connecter.
Page 77
Use a screwdriver to screw the 4 screws S11: Set up the speaker. to fix the VGA and DVI connecter. Red left and green right S12: Set up the keypad board and the S10: Fix the chassis in the bezel. touchpad board.
Page 78
S13: Fix the touchpad board and the keypad S15: Assemble the stand and fix it. board. Connect the two board S14: Assemble the back cover. S16: Assemble the left and right hinge cover.