Table of Contents
Advertisement
Quick Links
EZ
Loop
AP100-PA Relay Board
•
S200P Sensor
•
S600SM Sensor
•
ACCESS
STATUS <
ONE
PROGRAM
!
Read and follow all U.L. and Safety Standards before installing any access device. Please refer to this manual and
qualified personnel for assistance. DO NOT install this device unless all entrapment and pinch points are eliminated.
Wireless Vehicle Detector
Product Manual
Installation Instructions
•
Program Instructions
•
WVD100
Revision 2.5E
1
Advertisement
Table of Contents
Related Manuals for Access One WVD100
Summary of Contents for Access One WVD100
- Page 1 WVD100 Wireless Vehicle Detector Loop AP100-PA Relay Board • S200P Sensor • S600SM Sensor • ACCESS STATUS < PROGRAM Product Manual Installation Instructions • Program Instructions • Read and follow all U.L. and Safety Standards before installing any access device. Please refer to this manual and qualified personnel for assistance.
-
Page 2: Table Of Contents
Above Ground Cap ..........12 Assemble the S200P Sensor ....... 13 Troubleshooting Chart ........22 S600SM Learn Button ......... 13 Limited Warranty Assemble the S600SM Sensor ......13 S600SM Sensor Detection ........13 Limited Warranty ..........23 WVD100, Rev 2.5E Page 2... -
Page 3: Quick Start
Use Up, Down, Enter buttons to enter time of relay action for needed settings, press Enter Relay 1 = Reverse Relay 3 = Shadow Relay 2 = Open Relay 4 = Auxiliary WVD100, Rev 2.5E Page 3... -
Page 4: Activate & Test Sensors
IMPORTANT: Read the entire manual for complete and 4. Place the sensor far enough away from the gate so the moving gate proper safety, installation and programming instructions. does not activate the sensor. Usually 8-10 feet from the gate. WVD100, Rev 2.5E Page 4... -
Page 5: Safety Information
DO NOT allow children to play near, on or with the gate, gate operator, or any of its controls. DO NOT allow pedestrian use of the vehicular gate. No one should cross the path of a moving gate! WVD100, Rev 2.5E Page 5... -
Page 6: System Overview
Connect Relay 4 to an auxiliary device. This can be used to arm a clear line of sight to the sensors. Access One keypad or phone entry, turn a camera on, turn a light on, etc. -
Page 7: External Antenna Kit
Installation External Antenna Kit: Antenna Line of Sight: Access One always recommends the use of Because significant signal strength is lost when a sensor is placed the external antenna kit to better the in the hole, it is very important to install the antenna in a location signal from the AP100 to each sensor. -
Page 8: Sensor Detection Overview
For example, Lane 1 would Expanded Area use ID 0001 and Lane 2 would use ID 0002. These IDs are field settable. Refer to the “Change ID” programming on Page 19. 6-8 feet Side to Side WVD100, Rev 2.5E Page 8... -
Page 9: Sensor Slide Gate Layout
This is usually 8-10 feet from the gate. Note: The Reverse Sensor near the swing of the gate should be 8-10 feet from the swing path of the gate. Mark the location of where each sensor will be installed. WVD100, Rev 2.5E Page 9... -
Page 10: Sensor Parking Gate Layout
The following diagram shows a parking gate application for two- way traffic with a free exit. For one-way traffic, the exit sensor is Access One always recommends testing the sensor above ground in not needed. (This diagram is a basic layout and does not show its desired location before drilling the hole to make sure the sensor safety devices, pedestrian gate, fencing, etc. -
Page 11: Unordinary Installation Suggestions
In some rare applications, it may be necessary to add a second antenna down the driveway to help with the signal and application. Install the sensor into the PVC sleeve the same as it would be installed in the driveway. Driveway WVD100, Rev 2.5E Page 11... -
Page 12: Installing The S200P Sensor In Snow
2. Cap must be secure enough to 2. Cap must be secure enough to prevent any stress or torque on prevent any stress or torque on the the inground housing. inground housing. WVD100, Rev 2.5E Page 12... -
Page 13: Assemble The S200P Sensor
The housing cover and baseplate MUST fit without any wires or screws preventing a tight and clean fit. WVD100, Rev 2.5E Page 13... -
Page 14: Installing The S600Sm Sensor With Epoxy
In such applications a cement epoxy similar to what is used to hold down highway reflectors can be used. One source we recommend is: https://stop-painting.com/order_form.asp Stop-Painting.com AP-43 Epoxy Kit for Road Reflectors—One Quart WVD100, Rev 2.5E Page 14... -
Page 15: Sensor Programming
AP100 to make it active. If a sensor is learned but Toggle Activates on 1st detect, deactivates on 2nd detect not made active, unplug the sensor battery until it is time to make the sensor active. WVD100, Rev 2.5E Page 15... -
Page 16: Sensor Active
Reset” on Page 14 for details. Select SENSOR, press Enter Select ACTIVE, press Enter Magnetized Select SENSORx, press Enter (x = Sensor being programmed) Screwdriver Select INACTIVE, press Enter Press and hold the Enter button to exit programming WVD100, Rev 2.5E Page 16... -
Page 17: Sensor Delete
X = width, Default = 20 Y = height, Default = 35 Z = Not used, Default = 100 Important: Access One cannot guarantee proper function Select PROGRAM, press Enter and detection when the sensitivity is changed. Select SENSOR, press Enter... -
Page 18: Sensor Time Schedules
Use of the Park Fail feature is at the relay functions on and off at certain times of the day or week. installers discretion and Access One will not be responsible for any failure, damage, or other cause if this feature does not work Example 1: An open sensor can be set to activate the open relay on properly. -
Page 19: Ap Programming
Hold the enter button to exit programming reset and then relearned after the new Unit ID. Function Action Activates alarm during a fault Does not activate the alarm during a fault CLEAR F Clears & resets the Fault Log in status WVD100, Rev 2.5E Page 19... -
Page 20: Relay Time Schedules
Active. In this case, the sensor will not reset and clear the fault since there is not a vehicle present. To reset the sensor, simply program the sensor Inactive and then Active again. WVD100, Rev 2.5E Page 20... -
Page 21: Status Menu
Select STATUS, press Enter Select CLOCK, press Enter AP100 Dimensions 5.50” wide, 4.25” high, 1” deep The date and time will be displayed S200P Dimensions 5” high, 1.90” wide S600SM Dimensions 6” x 6” wide, 1.50” high WVD100, Rev 2.5E Page 21... -
Page 22: Troubleshooting
Sensor detects and shows on LCD but Make sure that Sensor is programmed to a relay. does not activate relay Make sure the relay is programmed to a function other than NONE. None is the default. WVD100, Rev 2.5E Page 22... -
Page 23: Limited Warranty
You MUST read, understand and agree with ALL items in this limited warranty! Access One Technologies warrants this product to be free of defects in workmanship and materials for a period of (1) one year from the date of purchase. Access One Technologies reserves the right of final determination to the cause of any defect or failure. Access One Technologies shall, at its option, either repair or replace this product if returned freight prepaid to Access One Technologies during the warranty period. - Page 24 www.AccessOneTechnologies.com...