Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Service Hints How to remove the backcover Remove the 18 fixing screws. (see Fig.5) SCREWS SCREWS Fig.5 How to remove the Pedestal assembly Lay the main unit face down. (see Fig.6) Fig.6 Remove the 4 fixing screws and the pedestal assembly. (see Fig.7) SCREWS Fig.7...
Chassis Board Layout G-BOARD P-BOARD A-BOARD K-BOARD V-BOARD Board Name Function A-Board Tuner, PC, AVSW, HQ1L, HDMI,CI Slot, Global Core, GENX, AV Terminal, SD Slot, Speaker out, ADV P-Board Power Supply, Main Input V-Board Remote Receiver, Bats, R/G LED G-Board Side AV Connector K-Board Main Switch...
Setting Inspection Voltage Confirmation Confirm the following voltages: P board Description Test Position Normal mode Stand by mode Active stand by mode point Panel 12V TP863 P2, pins 16, 17 12,0V +/- 0,35V 12V +/- 0,35V 16V_Audio TP858 P2, pins 20, 21 16V +/- 1V 16V +/- 1V SUB_9V...
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button. Panasonic 2008LCD 32HD TX-32LXD85 Self Check Complete 1723 O.K.
Power LED blinking timing chart Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit. Blinking Blinking timing Contents...
Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu How to enter SERVICE While pressing (-/v) button on TV unit, press on the remote control for 3 times within 2 seconds.
SERVICE SERVICE Peaks SOFT 2.106 OPTION 1 0c Key Command ADJUST Peaks EEP 01.05.0012 OPTION 2 00 WB-ADJ LSI DATA 0.00.04 OPTION 3 OPTION STBY SOFT 1.01.00 Model ID • SRV-TOOL STBY EEP 1.03.00 03141100 Press the 3/4 button to change the adjustment values or function. STBY ROMCOR 1.01.00 00000004...
Option Bytes Description OPTION1 ATP Speed Slow (1) / Fast (0) TXT Ch On (1) / Off (0) ID-1 On (1) / Off (0) Macrovision Auto Evaluation On (1) / Off (0) SRS Surround On (1) / Off (0) Teletext Top Off (1) / On (0) Equalizer Not Use...
Adjustment Method Sub-Contrast/White Balance Adjustment Instrument Name Connect to Remarks Remote controller Correlation can be also taken by LCD WB meter (Minolta CS-1000A equivalent) CA-210 or equivalent Comunication jig Computer for external control Procedure Remarks Let the panel standfor more than 3 hours at more than 20 °C.
Replacement Parts List Important Safety Notice Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order. RTL (Retention Time Limited) Note: The marking (RTL) indicates that the Retention Time is Limited for this item.
Page 41
Cct Ref Parts Number Description Cct Ref Parts Number Description C8319 F1G1E103A123 S.M.CAP 10nF RELAYS C8320 F1G1E103A123 S.M.CAP 10nF RL801 K6B2ADA00007 RELAY C8321 F1G1E103A123 S.M.CAP 10nF C8327 F1H1A1050032 S.M.CAP 1000nF DIFFERENCES FOR MODEL TX--32LXD85 C8328 F1H1A1050032 S.M.CAP 1000nF C8329 F1G1E103A123 S.M.CAP 10nF EXPLODED VIEW...
Page 42
Cct Ref Parts Number Description Cct Ref Parts Number Description TQB0E0565K DANISH TKZ0E9160 LCD BRACKET TQB0E0565M BULGARIAN L5EDD9Q00004 LCD PANEL TQB0E0565N ROMANIAN TBM0E1206 MODEL LABEL TQB0E0565O LATVIAN TTX0E0007 PEDESTAL ASSY TQB0E0565P POLISH TKP0E91801 POWER BUTTON BRACKET TQB0E0565Q HUNGARIAN TUA0E3400 R CHASSIS FRAME BRACKE TQB0E0565R CZECH TKP0E35301...
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM (Ω) (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.