Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
WARNING! Ensure all Health & Safety, local authority and general workshop practice regulations are
strictly adhered to when using tools.
DO NOT use equipment if damaged.
Maintain the equipment in good and clean condition
for best and safest performance.
If required, ensure vehicle to be worked on is
adequately supported with axle stands, ramps and
chocks.
Wear approved eye protection. A full range of personal
safety equipment is available from your Sealey dealer.
Wear suitable clothing to avoid snagging. DO NOT
wear jewellery and tie back long hair.
Account for all tools and equipment being used and
DO NOT leave them in, on or near engine.
DO NOT use this equipment when tired or under the
influence of drugs, alcohol or intoxicating medication.
When not in use, place in protective case and store
in a safe, dry, childproof area.
IMPORTANT: Always refer to the vehicle
manufacturer's service instructions, or a proprietary
manual, to establish the current procedure and data. These instructions are provided as a guide only.
WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible
conditions and situations that may occur. It must be understood that common sense and caution are
factors which cannot be built into this product, but must be applied by the operator.
2.
INTRODUCTION
Ø57mm Gauge fitted with heavy
rubber bumper, 150mm hose and
M14/M18 fitting. Scale reads from
0-20bar(0-290psi). Suitable for most
petrol engined cars and light
commercials. Includes five adaptors
and two thread chasers covering
four plug thread sizes. Supplied in
carry-case.
3.
TEST PROCEDURE
WARNING! Always release the pressure via the release valve before disconnecting the tester.
Press the release valve slowly to release the pressure gradually. Refer to fig.1.
NOTE! A variation in compression readings between cylinders is often a better indication of engine
faults than the absolute values of compression.
3.1
Run the engine until it reaches the normal operating temperature.
3.2
Stop the engine and disconnect all HT leads, numbering them according to the cylinder to which they
were connected.
WARNING! At normal operating temperature the engine and components will be HOT.
3.3
Loosen all spark plugs by about half a turn, but DO NOT remove them.
3.4
Using an air hose or wire brush, remove all the dirt and debris from the spark plug wells.
3.5
Remove the spark plugs and place them on a clean, flat surface in the cylinder order in which they
were removed.
© Jack Sealey Limited
INSTRUCTIONS FOR:
PETROL COMPRESSION TEST KIT 8pc
MODEL No:
and properly maintained, give you years of trouble free performance.
Original Language Version
VSE200.V3
fig.1
fig.2
vSE200.v3
Issue No: 1 - 14/06/12
Advertisement
Related Manuals for Sealey VSE200.V3
Summary of Contents for Sealey VSE200.V3
- Page 1 VSE200.V3 MODEL No: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
- Page 2 Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.