hit counter script
Sony HT-MT500 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Speaker System
  5. HT-MT500
  6. Service manual

Sony HT-MT500 Service Manual

Hide thumbs Also See for HT-MT500:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
Ver. 1.0 2017.02
• All of the units included in the HT-MT500 (SA-
MT500/SA-WMT500/Remote control) or HT-
MT501 (SA-MT501/SA-WMT501/Remote con-
trol) are required to confi rming operation of SA-
MT500/MT501. Check in advance that you
have all of the units.
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
COMPONENT MODEL NAME
Bar Speaker (Active Speaker System)
Subwoofer (Active Subwoofer)
• Please refer to service manual separately issued for Subwoofer.
Amplifier section
POWER OUTPUT (rated)
Front L + Front R: 25W + 25W
(at 4ohms, 1kHz, 1% THD)
POWER OUTPUT (reference)
Front L/Front R speaker blocks: 35W
(per channel at 4ohms, 1kHz)
Inputs
ANALOG IN
TV IN (OPT)
Outputs
HDMI OUT (TV (ARC))
HDMI Section
Connector
Type A (19pin)
USB section
(USB) port:
Type A (For connecting USB memory)
LAN section
LAN(100) terminal
100BASE-TX Terminal
Wireless LAN section
Communication system
IEEE 802.11 a/b/g/n
Frequency band
2.4GHz, 5GHz
9-896-356-01
2017B33-1
Sony Video & Sound Products Inc.
©
2017.02
HT-MT500/MT501
HT-MT500
HT-MT501
SA-MT500
SA-MT501
SA-WMT500
SA-WMT501
SPECIFICATIONS
BLUETOOTH section
Communication system
BLUETOOTH Specification version 4.1
Output
BLUETOOTH Specification Power
Class1
Maximum communication range
1)
Line of sight approx. 30m
Maximum number of devices to be
registered
9 devices
Frequency band
2.4 GHz band (2.4GHz - 2.4835GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
2)
Compatible BLUETOOTH profiles
A2DP 1.2 (Advanced Audio Distribution
Profile)
AVRCP 1.5 (Audio Video Remote
Control Profile)
3)
Supported Codecs
4)
5)
SBC
, AAC
, LDAC
Transmission range (A2DP)
20 Hz - 40,000 Hz (LDAC sampling
frequency 96kHz with 990 kbps
transmission)
20 Hz - 20,000 Hz (Sampling frequency
44.1kHz)
1)
The actual range will vary depending on
factors such as obstacles between
devices, magnetic fields around a
microwave oven, static electricity,
cordless phone use, reception
sensitivity, the operating system,
software applications, etc.
2)
BLUETOOTH standard profiles indicate
the purpose of BLUETOOTH
communication between devices.
3)
Codec: Audio signal compression and
conversion format
4)
Abbreviation for Subband Codec
5)
Abbreviation for Advanced Audio
Coding
Photo: SA-MT500
Front L/Front R speaker block section
Speaker system
Full range speaker system, Acoustic
suspension
Speaker
45mm (1 13/16 in.) cone type
General
Power requirements
DC 19.5 V (using the supplied AC
adapter connected to AC 100 V - 240 V,
50 Hz/60Hz power supply)
Power consumption (using the supplied
AC adapter)
On: 30W
For details about the power
consumption during standby mode,
see "Power Consumption by the
Setting Value for Each Standby
Mode".
Dimensions* (approx.) (w/h/d)
500mm × 64mm × 108mm
(19 3/4 in x 2 5/8 in x 4 3/8 in)
(without grille frame)
500mm × 64mm × 110mm
(19 3/4 in x 2 5/8 in x 4 3/8 in)
(with grille frame)
*Not including projection portion
Mass (approx.)
2kg (4 lb 6 1/2 oz)
Compatible iPod/iPhone models
The compatible iPod/iPhone models are as
follows. Update your iPod/iPhone with the
latest software before using with the
system.
BLUETOOTH technology works with:
iPhone 7 Plus/iPhone 7/iPhone SE/
iPhone6s Plus/iPhone 6s/iPhone 6 Plus/
iPhone6/iPhone 5s/iPhone 5c/iPhone 5/
iPhone 4s
iPod touch (6th generation)/iPod touch
(5th generation)
ACTIVE SPEAKER SYSTEM
SA-MT500/MT501
AEP Model
UK Model
Wireless transmitter section
Communication system
Wireless Sound Specification version
3.0
Frequency band
5.2GHz (5.180GHz - 5.240GHz)
5.8GHz (5.736GHz - 5.814GHz)
Modulation method
DSSS
What's in the Box
• Bar Speaker (1)
• Subwoofer (1)
• Remote control (1)
• R03 (size AAA) battery (2)
• Optical digital cable (1)
• AC adapter (1)
• AC power cord (mains lead) (1)
• AC power cord (mains lead) for the
subwoofer (1)
• Speaker pad for the subwoofer (4)
• Startup Guide
• Operating Instructions
Design and specifications are subject to
change without notice.
HT-MT500/MT501
SOUND BAR
SA-MT500/MT501

Advertisement

Table of Contents
loading

Related Manuals for Sony HT-MT500

Summary of Contents for Sony HT-MT500

  • Page 1 SERVICE MANUAL AEP Model UK Model Ver. 1.0 2017.02 • All of the units included in the HT-MT500 (SA- MT500/SA-WMT500/Remote control) or HT- MT501 (SA-MT501/SA-WMT501/Remote con- trol) are required to confi rming operation of SA- MT500/MT501. Check in advance that you have all of the units.
  • Page 2 Bluetooth SBC, it operates without any down- SIG, Inc. and any use of such marks by Sony conversion of the Hi-Res Audio content*, Corporation is under license. Other and allows approximately three times...

  • Page 3: Table Of Contents

    ADVANCE PREPARATION WHEN CONFIRMING OP- TROUBLESHOOTING .......... 35 ERATION All of the units included in the HT-MT500 (SA-MT500/SA- DIAGRAMS WMT500/Remote control) or HT-MT501 (SA-MT501/SA-WMT501/ 5-1. Block Diagram - MAIN Section - ........38 Remote control) are required to confi rming operation of SA- 5-2.
  • Page 4 HT-MT500/MT501 MODEL IDENTIFICATION RESETTING THE SYSTEM Distinguish by Part No. and Destination code of the model number It can return each settings to the initial state of factory shipment. Note 1: To delete the Bluetooth pairing information, select the “All Set- label on the bottom side of the main unit.
  • Page 5 HT-MT500/MT501 NETWORK INFORMATION WRITING METHOD Diag When the MB-1610 board or WLAN/BT combo card is replaced, Category: Wireless LAN Test perform the writing work of the network information in the service mode. Diag Procedure: Category: Wireless LAN Test 1. Connect this unit with TV monitor.
  • Page 6 HT-MT500/MT501 NETWORK CONNECTION CHECKING METHOD 9. Press the [V]/[v] buttons on the remote commander to select the “Auto”, and press the [b] button on the remote command- When the MB-1610 board or WLAN/BT combo card is replaced, check the connection of wireless/wired LAN.
  • Page 7 HT-MT500/MT501 NOTICE OF MAC ADDRESS CHANGE TO CUSTOM- 10. Press the [SECURE LINK] button on the subwoofer. 11. The message “Finish” is displayed on the TV monitor, the power indicator of the subwoofer is lit in orange and secure When the MB-1610 board or WLAN/BT combo card is replaced, link is completed.
  • Page 8 HT-MT500/MT501 BOND FIXED POSITION OF ELECTRICAL PARTS COLOR VARIATION When the parts that fi xed on the board by the bond have been re- HT-MT500 HT-MT501 moved, fi x the parts by using the bond (ADHESIVE (SC608Z2)) SA-MT500 SA-MT501 in the mounting to the board. (Refer to the fi gure below) Charcoal Crème...

  • Page 9: Disassembly

    HT-MT500/MT501 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-2. GRILLE ASSY, HI-RES LABEL (Page 10) 2-3. USB COVER (Page 10) 2-4. TOP PANEL BLOCK, BOTTOM PANEL BLOCK (Page 11) BOTTOM PANEL BLOCK TOP PANEL BLOCK 2-12.

  • Page 10: Grille Assy, Hi-Res Label

    HT-MT500/MT501 Note: Follow the disassembly procedure in the numerical order given. 2-2. GRILLE ASSY, HI-RES LABEL 1 grille assy 2 HI-RES label top side right side HI-RES label Upward arrow. – – 3 mm – – 13 mm 2 degrees or less.

  • Page 11: Top Panel Block, Bottom Panel Block

    HT-MT500/MT501 2-4. TOP PANEL BLOCK, BOTTOM PANEL BLOCK 1 eight screws (BVTP3 left side front side 1 eight screws (BVTP3 Note: Lay a soft piece of cloth under the unit to avoid damaging the top panel. top side 2 Lift up the top cabinet block in the direction of the arrow at about a 90-degree angle.

  • Page 12: Top Panel Assy Block

    HT-MT500/MT501 2-5. TOP PANEL ASSY BLOCK CN1901 FFC 12P Bend. top panel block right side rear side front side terminal side TOUCH board 1 FFC 12P Note: Lay a soft piece of cloth under the unit (CN1901) to avoid damaging the top panel.

  • Page 13: Touch Board

    HT-MT500/MT501 2-6. TOUCH BOARD packing (VG2-2) packing (VG2) guide line guide line guide line guide line TOUCH board rear side rear side TOUCH board guide line NFC board packing (VG2) packing (VG2) (center) 1 packing (VG2-2) left side 3 packing (VG2)

  • Page 14: Nfc Board

    HT-MT500/MT501 2-7. NFC BOARD Note 1: When the NFC board is replaced, refer to “NFC CONNEC- TION CHECKING METHOD” on page 6. 4 Gradually peel off the NFC board with a flathead screwdriver, etc. packing (VG2-2) Note 3: The NFC board is affixed to the top guide line panel with a strong adhesive sheet.

  • Page 15: Front Panel Block, Speaker Block

    HT-MT500/MT501 2-8. FRONT PANEL BLOCK, SPEAKER BLOCK Bend. FFC 12P FFC 12P hole Press. front side guide line double adhesive tape left side top side FFC 12P 1 Peel the FFC 12P off of the double adhesive tape. front side...

  • Page 16: Display Board Block, Front Panel

    HT-MT500/MT501 2-9. DISPLAY BOARD BLOCK, FRONT PANEL left side 6 front panel 2 claw Display bracket is not visible (inside the claw) 2 claw claw boss bottom side bottom side boss display bracket top side hole – – right side...

  • Page 17: Organic El Indicator Element, Display Board

    HT-MT500/MT501 2-10. ORGANIC EL INDICATOR ELEMENT, DISPLAY BOARD The opposite side FFC 22P is terminal side. filament tape CN1406 DISPLAY board LED cushion DISPLAY board CN1410 (sub material) The opposite side is terminal side. 3 filament tape D1401 4 FFC 22P...

  • Page 18: Loudspeaker (L-Ch, R-Ch)

    HT-MT500/MT501 2-11. LOUDSPEAKER (L-CH, R-CH) Note 2: When connecting the terminals of the speaker connection cable to the loudspeaker, be careful of the terminal direction of the terminals. (narrow) speaker connection cable (2P) loudspeaker (R-ch) terminal front side (wide) 3 Pull out the speaker block right side in the direction of the arrow.

  • Page 19: Bar-Amp Board Block

    HT-MT500/MT501 2-12. BAR-AMP BOARD BLOCK bottom panel block left side FFC 26P CN6013 2 MB-1610 board cable connector (CN6015) 1 MB-1610 board cable connector (CN6014) 3 FFC 26P front side (CN6013) The opposite side is terminal side. 4 screw front side...

  • Page 20: Mb-1610 Board-1

    HT-MT500/MT501 2-14. MB-1610 BOARD-1 USB-WSCHUKEI • Continued on 2-15 (page 21). board cable MB-1610 board MB-1610 USB-WSCHUKEI CN503 board board cable [black] C565 Pull. Press. WLAN/BT combo front side card cable wire Press. Pass the USB-WSCHUKEI board cable across the front side of the C565.

  • Page 21: Mb-1610 Board-2

    HT-MT500/MT501 2-15. MB-1610 BOARD-2 Note 1: When the MB-1610 board is replaced, refer to “NOTE OF REPLACING THE MB-1610 BOARD OR WLAN/BT COMBO CARD” on page 4. 1 three screws (BVTP3 left side 2 screw 1 three screws (BVTP3 front side...

  • Page 22: Wlan/Bt Combo Card Block

    HT-MT500/MT501 2-16. WLAN/BT COMBO CARD BLOCK 1 screw (BVTP3 1 screw (BVTP3 1 three screws (BVTP3 hole 2 chassis block Note: When installing the chassis block, align the two ribs and two holes. 1 screw (BVTP3 left side hole 1 screw...

  • Page 23: Wlan/Bt Combo Card

    HT-MT500/MT501 2-17. WLAN/BT COMBO CARD Note 1: When the WLAN/BT combo card is replaced, refer to “NOTE OF REPLACING THE MB-1610 BOARD OR WLAN/BT COMBO CARD” on page 4. WLAN/BT combo 2 screw card block (BVTP3 MB-1610 board (CN502) top side...

  • Page 24: Btw Board

    HT-MT500/MT501 2-18. BTW BOARD non woven non woven Pass the coaxial harnss across fabric (T0.3) fabric (T0.3) the rear side of the screw boss. rear side coaxial harnss rear side left side An arrow is turning to the right. guide line...

  • Page 25: Usb-Wschukei Board

    HT-MT500/MT501 2-19. USB-WSCHUKEI BOARD guide line 4 USB-WSCHUKEI board cable top side connector (CN1553) 5 USB-WSCHUKEI packing (VG2-2) board block 1 screw 1 screw (BVTP3 – – (BVTP3 7 packing (VG2-2) 3 USB-WSCHUKEI board cable rear side 6 screw connector (CN1501)

  • Page 26: Rf Modulator

    HT-MT500/MT501 2-20. RF MODULATOR RF modulator block rear side right side top side WS module cushion guide line 1 WS module cushion modulator front side guide line WS module – – 1 WS module cushion cushion 4 WS holder block...

  • Page 27: Test Mode

    HT-MT500/MT501 SECTION 3 TEST MODE ALL RESET 6. In the state of step 3, touch the [+] button and “VG2_B” (mod- el name) is displayed on the front panel display. (“B” will dis- It can initialize all settings of IFCon and SYSCON.
  • Page 28 HT-MT500/MT501 TOUCH-SENSOR DEBUG AMP TEST It can inspect the sensitivity of the touch key. It can perform the AMP setting and measurement. If the operation in the touch key at the “PANEL TEST” (on page 27) was insecure, check the sensitivity of the touch key in this Procedure: mode.
  • Page 29 HT-MT500/MT501 WIRELESS SOUND COLD RESET SERVICE MODE Note: The operation in this mode must a TV monitor and supplied remote It can initialize various backup information of Subwoofer (SA- commander. WMT500/WMT501). Setting method of the service mode: Preparation: 1. Connect this unit with TV monitor.
  • Page 30 HT-MT500/MT501 2. Menu Tree Service Mode Menu Device Test Diag Service Mode Menu [1] Diag [1] Diag [2] Log [2] Log [3] Factory Initialize [3] Factory Initialize [4] Network [4] Network Video Test [5] Version Up [5] Version Up Not used in this unit...
  • Page 31 HT-MT500/MT501 3. Service Mode Menu (Top Menu) 4. Diag (Device Test) This is the top menu of service mode. This screen is used for test of each devices mounted on the board. Each function is accessed from this screen. Operation:...
  • Page 32 HT-MT500/MT501 7. Diag (Wireless LAN Test) Diag This screen performs wireless LAN/Miracast test. Category: Wireless LAN Test Screen 1: Selects the wireless LAN test category Operation: Diag [B]/[b] Selects the category Category: Wireless LAN Test [v]/[ ] Moves to the selected category...
  • Page 33 HT-MT500/MT501 11. Diag (Bluetooth Device Test) Diag This screen performs Bluetooth device test. Category: Bluetooth Device Test Screen 1: Selects the Bluetooth device test category Operation: Diag [B]/[b] Selects the category Category: Bluetooth Device Test [v]/[ ] Moves to the selected category...
  • Page 34 HT-MT500/MT501 12. Log 17. EMC Test Mode Note: Not used in this unit. Note: Not used for the servicing. 13. Factory Initialize (Factory Settings) 18. Drive Note: Not used in this unit. Return all of the unit setting to their factory defaults (Refer to “RE- SETTING THE SYSTEM”...

  • Page 35: Troubleshooting

    HT-MT500/MT501 SECTION 4 TROUBLESHOOTING 1. “PRTCT”, “PUSH” and “POWER” is displayed on the front panel display after turning the power on “PRTCT”, “PUSH” and “POWER” is alternately displayed on the front panel display after turning the power on. IC6001 on the BAR-AMP board is Replace the IC6001 on the BAR-AMP board.
  • Page 36 HT-MT500/MT501 2. The video and audio of HDMI is not outputted The video and audio of HDMI is not outputted. The voltage of the following is about 3.3 V. The voltage of the following is 1.2 V. MB-1610 board: IC301 pin 5...
  • Page 37 HT-MT500/MT501 3. The sound is not outputted The sound is not outputted. Entering the “DEMO MODE” (touch Check the signal path for being inputted the [ ] button for five seconds), to the IC101 on the MB-1610 board, and and then the “DEMO MODE” sound then replace the defective part, or replace is outputted.

  • Page 38: Diagrams

    HT-MT500/MT501 SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM - MAIN Section - IC101 (1/3) ARC_SPDIF (Page 39) >001B C24 ARC SIGNAL PATH AMP_D1FL/FR, AMP_D3SW, AMP_BCK, AMP_LRCK AMP_D1FL/FR : AUDIO (ANALOG) >003B AOSDATA0 OPTICAL TV IN : AUDIO (DIGITAL) RECEIVER B23 OPTICAL...

  • Page 39: Block Diagram - Amp/Hdmi Section

    HT-MT500/MT501 5-2. BLOCK DIAGRAM - AMP/HDMI Section - AUDIO CODEC DIGITAL POWER AMP IC6009 IC6001 AMP_D1FL/FR, AMP_D3SW, L6021 AMP_BCK, AMP_LRCK AMP_D1FL/FR >003B SDIN1 PWMOUT1NR 21 INPUT_A OUT_A 39 AMP_D3SW SDIN2 (L-CH) BUFFER (Page 38) AMP_BCK BCKI OUT_A 40 IC6015 AMP_LRCK...

  • Page 40: Block Diagram - Panel/Power Supply Section

    HT-MT500/MT501 5-3. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section - E5.2V SYSTEM CONTROLLER IC5006 (3/3) +3.3V 3.3V REGULATOR REGULATOR +3.3V IC306 IC701 MTKSTB_3.3V REGULATOR NFC BOARD IC305 NFC_SDA 19 NFC_DATA NFC_SCL 20 NFC_CLK PCON_WOL_STB NFC_IRQ 21 NFC_IRQ DC/DC +3.3V DDR1.5V CONVERTER D3.3V...
  • Page 41 HT-MT500/MT501 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location (In addition to this, the necessary note is printed in each block.) WLAN/BT combo card (WIFI1) For Printed Wiring Boards. For Schematic Diagrams. Note: Note: •...

  • Page 42: Printed Wiring Board - Mb-1610 Board (Side A)

    HT-MT500/MT501 5-4. PRINTED WIRING BOARD - MB-1610 Board (Side A) - • See page 41 for Circuit Boards Location. • : Uses unleaded solder. HDMI OUT (100) (WS WIRED CONNECTION) TV (ARC) MB-1610 BOARD (SIDE A) (CHASSIS) R794 CN707 CN602...

  • Page 43: Printed Wiring Board - Mb-1610 Board (Side B)

    HT-MT500/MT501 5-5. PRINTED WIRING BOARD - MB-1610 Board (Side B) - • See page 41 for Circuit Boards Location. • : Uses unleaded solder. TV IN (OPT) MB-1610 BOARD (SIDE B) C527 CN704 IC701 R757 JL603 C710 R818 CL743 C622...

  • Page 44: Printed Wiring Board - Bar-Amp Board (Side A)

    HT-MT500/MT501 5-6. PRINTED WIRING BOARD - BAR-AMP Board (Side A) - • See page 41 for Circuit Boards Location. • : Uses unleaded solder. BAR-AMP BOARD (SIDE A) J6002 ANALOG IN D6013 (IR REPEATER) D6013 C6036 FB6013 R6177 R6178 LN6005...

  • Page 45: Printed Wiring Board - Bar-Amp Board (Side B)

    HT-MT500/MT501 5-7. PRINTED WIRING BOARD - BAR-AMP Board (Side B) - • See page 41 for Circuit Boards Location. • : Uses unleaded solder. BAR-AMP BOARD (SIDE B) J6001 19.5V – JL6017 JL6016 D6005 R6210 R6219 D6006 Q6012 JL6014 Q6013...

  • Page 46: Schematic Diagram - Bar-Amp Board (1/3)

    HT-MT500/MT501 5-8. SCHEMATIC DIAGRAM - BAR-AMP Board (1/3) - • See page 52 for Waveforms. • See page 55 for IC Pin Function Description. BAR-AMP BOARD (1/3) CN6015 JL6017 DEMO JL6016 JL6015 MB-1610 BOARD (1/5) JL6014 C6176 C6208 C6191 C6192...

  • Page 47: Schematic Diagram - Bar-Amp Board (2/3)

    HT-MT500/MT501 5-9. SCHEMATIC DIAGRAM - BAR-AMP Board (2/3) - • See page 53 for IC Block Diagrams. BAR-AMP BOARD (2/3) R6160 0.01 JL6008 R6093 C6087 C6045 R6001 C6046 C6035 IC6001 R6161 0.01 0.01 DIGITAL POWER AMP R6094 Q6004 IC6001 2PC4081R-115...

  • Page 48: Schematic Diagram - Bar-Amp Board (3/3)

    HT-MT500/MT501 5-10. SCHEMATIC DIAGRAM - BAR-AMP Board (3/3) - • See page 52 for Waveforms. • See page 53 for IC Block Diagrams. BAR-AMP BOARD (3/3) L6015 2.2uH L6016 R6251 L6012 R6260 10uH 10uH C6227 JL6049 >003S BAR-AMP BOARD IC6011...

  • Page 49: Printed Wiring Board - Usb-Wschukei Board

    HT-MT500/MT501 5-11. PRINTED WIRING BOARD - USB-WSCHUKEI Board - • See page 41 for Circuit Boards Location. • : Uses unleaded solder. USB-WSCHUKEI BOARD (COMPONENT SIDE) MB-1610 BOARD (Page 42) >05P CN503 USB-WSCHUKEI BOARD (CONDUCTOR SIDE) W1501 R1552 (CHASSIS) CN1553...

  • Page 50: Printed Wiring Board - Display Board

    HT-MT500/MT501 5-13. PRINTED WIRING BOARD - DISPLAY Board - • See page 41 for Circuit Boards Location. • : Uses unleaded solder. DISPLAY BOARD (SIDE A) C1420 JL1406 D1404 CL1453 CL1456 CL1410 CL1424 CL1425 JL1405 CL1426 CL1427 C1422 D1406 CL1440...

  • Page 51: Printed Wiring Board - Btw Board

    HT-MT500/MT501 5-15. PRINTED WIRING BOARD - BTW Board - • See page 41 for Circuit Boards Location. • : Uses unleaded solder. BTW BOARD (SIDE A) J2401 ANT1 PATTERN ANTENNA (FOR BLUETOOTH) (11) 1-980-574- WIFI1 WLAN/BT >02P COMBO BTW BOARD...
  • Page 52 HT-MT500/MT501 • Waveforms – BAR-AMP Board – – USB-WSCHUKEI Board – IC6009 qa (XTI) IC1502 qf 4.4 Vp-p 1.9 Vp-p 20.8 s 21 ns 1 V/DIV, 20 ns/DIV 2 V/DIV, 20 s/DIV IC6015 qh IC1502 qh 4.3 Vp-p 4.8 Vp-p...
  • Page 53 HT-MT500/MT501 • IC Block Diagrams – BAR-AMP Board – IC6001 TAS5624ADDVR-S GVDD_AB 1 BST_A BST_B VDD 2 OC_ADJ 3 RESET 4 OUT_A ANALOG PWM & TIMING GATE- LOOP FILTER CONTROL DRIVE INPUT_A 5 – OUT_A RECEIVER PVDD_AB PVDD_AB PVDD_AB INPUT_B 6 ANALOG PWM &...
  • Page 54 HT-MT500/MT501 IC6011 ‒ 6013 TPS54334DDAR BOOT 1 8 PGOOD BOOT THERMAL 7 EN CHARGE HICCUP SHUTDOWN VIN 2 HICCUP SHUTDOWN UVLO ENABLE COMPARATOR LOGIC SHUTDOWN ENABLE THRESHOLD LOGIC VOLTAGE MINIMUM REFERENCE CURRENT CLAMP SENSE PULSE SKIP 6 COMP BOOT UVLO –...
  • Page 55 HT-MT500/MT501 • IC Pin Function Description BAR-AMP BOARD IC6009 CXD3776ER-T9 (AUDIO CODEC) Pin No. Pin Name Description 1, 2 SDIN1, SDIN2 Audio signal input from the SoC LRCKO L/R sampling clock signal input/output terminal Not used BCKO Bit clock signal input/output terminal...

  • Page 56: Exploded Views

    HT-MT500/MT501 SECTION 6 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • The mechanical parts with no reference The components identifi ed by mark 9 con- they may have some difference from the number in the exploded views are not sup- tain confi...

  • Page 57: Top Panel Section

    HT-MT500/MT501 6-2. TOP PANEL SECTION front side speaker section not supplied left side not supplied FFC5 not supplied (6P) right side top side Note 1: As for WIRE KIT (FFC/SA-MT500), all fl exible fl at cables Note 2: When the complete NFC board (Ref. No. 57) is replaced, refer (Ref.

  • Page 58: Speaker Section

    HT-MT500/MT501 6-3. SPEAKER SECTION left side front side not supplied FFC3 (22P) not supplied OLED1 not supplied not supplied not supplied supplied not supplied not supplied (DISPLAY board) FFC4 not supplied not supplied (12P) not supplied right side not supplied...

  • Page 59: Bar-Amp Board Section

    HT-MT500/MT501 6-4. BAR-AMP BOARD SECTION not supplied not supplied not supplied not supplied not supplied not supplied supplied MB-1610 board section Note: When the complete BAR-AMP board (Ref. No. 151) is re- placed, refer to “BOND FIXED POSITION OF ELECTRICAL PARTS”...

  • Page 60: Mb-1610 Board Section

    HT-MT500/MT501 6-5. MB-1610 BOARD SECTION not supplied FFC1 not supplied (26P) supplied not supplied not supplied not supplied not supplied bottom panel section Note 1: As for WIRE KIT (FFC/SA-MT500), all fl exible fl at cables Note 2: When the complete MB-1610 board (Ref. No. 202) is re- (Ref.

  • Page 61: Bottom Panel Section

    HT-MT500/MT501 6-6. BOTTOM PANEL SECTION not supplied WIFI1 not supplied not supplied not supplied supplied not supplied not supplied (BTW board) not supplied not supplied supplied supplied not supplied supplied supplied FFC2 supplied (26P) Note 1: As for WIRE KIT (FFC/SA-MT500), all fl exible fl at cables Note 2: When the WLAN/BT combo card (Ref.

  • Page 62: Electrical Parts List

    HT-MT500/MT501 SECTION 7 BAR-AMP ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS The components identifi ed by mark 9 con- the parts list may be different from the uF: μF tain confi dential information. parts specifi ed in the diagrams or the com- •...
  • Page 63 HT-MT500/MT501 DISPLAY MB-1610 TOUCH USB-WSCHUKEI Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark DISPLAY BOARD < IC > ************* * IC1502 6-722-068-01 IC 74LCX541FT < CONNECTOR > ************************************************************* CN1400 1-843-407-31 FPC CONNECTOR (ZIF) (11PIN) MISCELLANEOUS CN1406...
  • Page 64 HT-MT500/MT501 Ref. No. Part No. Description Remark ACCESSORIES ************ 4-687-808-32 STARTUP GUIDE (ENGLISH) (UK) 4-687-808-42 STARTUP GUIDE (FRENCH, SPANISH) (AEP) 4-687-808-52 STARTUP GUIDE (GERMAN, DUTCH) (AEP) 4-687-808-62 STARTUP GUIDE (ITALIAN, POLISH) (AEP) 4-687-810-32 MANUAL, INSTRUCTION (Operating Instructions) (ENGLISH) (UK) 4-687-810-42...
  • Page 65 HT-MT500/MT501 MEMO...
  • Page 66 HT-MT500/MT501 REVISION HISTORY Ver. Date Description of Revision 2017.02 How to search for a contact point of signal lines or the like in DIAGRAMS SECTION If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use the PDF fi...

This manual is also suitable for:

Ht-mt501Sa-mt500Sa-mt501

Table of Contents