55" class (54.6" diag.) sony led hx850 internet tv (40 pages)
Summary of Contents for Sony X930E Series
Page 1
SERVICE MANUAL *Table of contents is on the last page. Please also utilize "Bookmarks“ function / "Find" function on Acrobat PDF data. X930E/940E Series ORIGINAL MANUAL ISSUE DATE: 1/2017 GN3TR CHASSIS KP Segment Version Date Subject 1/2017 Original manual issue. LCD TV 9-888-812-01...
MODEL LIST MODEL COLOR COMMANDER DEST. MODEL COLOR COMMANDER DEST. XBR-55X930E Black RMF-TX200U (UC2) US/CND XBR-65X930E Black RMF-TX200U (UC2) US/CND (LA1) MEXICO XBR-75X940E Black RMF-TX200U ((UC2) US/CND (LA1) MEXICO XBR-55/65X930E, 75X940E...
Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual.
Page 4
Les composants identifi es par une trame et par une marque du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi es dans le present manuel.
Page 5
WARNINGS AND CAUTIONS USE CAUTION WHEN HANDLING THE LCD PANEL When repairing the LCD panel, be sure you are grounded by using a wrist band. When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover. Do not press on the panel or frame edge to avoid the risk of electric shock.
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges. 2.
Page 7
SAFETY CHECK-OUT Leakage Test (To protect electric shock when customer touch the terminal.) Leakage current can be measured by V: Voltmeter or oscilloscope (r.m.s. or peak reading) Stabilized power supply instrument and isolated voltage transformer: Use too much current capacity and isolated voltage transformer does not need to use stabilized power supply equipment Specification of RMS volt meter: Input resistance >...
SELF DIAGNOSIS FUNCTION The units in this manual contain a self-diagnostic function. If an error occurs, the Smart Core Red LED will automatically begin to flash. The number of times the LED flashes translates to a probable source of the problem. A definition of the Smart Core Red LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 9
SELF DIAGNOSIS FUNCTION Error Item Error count [SELF DIAGNOSTIC SCREEN DISPLAY] SELF CHECK Format of error timestamps YYMMDDhhmmss (in UTC) Back << Example: MAIN POWER 000000000000 000000000000 000000000000 120823132523 -> Aug 23 2012 13:25:23 UTC DC ALERT 000000000000 000000000000 000000000000 * Only when time is set, an error timestamp is saved.
ADJUSTMENT HOW TO ENTER SERVICE MODE 1) Turn on the main power switch to place the set in standby condition. 2) Press the buttons on the remote commander as follows, and entering service mode. 3) Service mode display. Service Mode Model Information >>...
Page 11
ADJUSTMENT SOFTWARE VERSION 1) In Service Mode, select “Model Information”, press “Enter” or “→” button to enter Status Information. Main Micro Service Mode SW Version: PKG1.1.0.03.26.1.00.0 Model NVM Version: 0043 CEI Model Information >> Boot Version: V1.00000000 PQ Version: 02000001 Self diagnosis History >>...
Page 12
ADJUSTMENT SERIAL NUMBER EDIT (1) Service Mode 1) In “Service Mode”, select “Model Information” by pressing “↑” or “↓” button then pressing “Enter” or Model Information >> “→” button to enter inside. Self diagnosis History >> Video / Audio >> 2) Select “Serial Number Edit”...
Page 13
ADJUSTMENT SERIAL NUMBER EDIT (2) YES is selected, the input data is saved into EEPROM. Model SERIAL NUMBER EDIT is grayed out and the serial number that has been input is displayed. Status Information >> Operator will not be able to edit anymore.
Page 14
ADJUSTMENT MODEL NUMBER SETTING 1) In “Service Mode”, select “Model Information” by pressing “↑” or “↓” button then pressing “Enter” or “→” button to enter inside. 2) Select “Model Number Setting” by pressing “↑” or “↓” button then pressing “Enter” or “→” button. 3) Press “↑”...
Page 15
ADJUSTMENT WB ADJUSTMENT (If necessary) In “Panel/PQ” service mode. c. To change data, press “←” or “→” button on remote commander. a. Go to “WB Adjustment” category by “↑” or “↓”. Service Mode Back << R WB Gain <[ ]> Model Information >>...
Page 16
ADJUSTMENT 2. In “WB/Mura/CUC data transfer”. WB/MURA/CUC DATA TRANSFER a. Select “WB/Gamma data transfer” by pressing “↑” or “↓” button on remote commander. (Please apply Main board or panel is replaced.) 1. In “Panel/PQ” service mode. b. To change the items, press “←” or “→” button on remote commander and press “Enter” a.
USB UPDATE *Please refer to another manual “Service Procedure for Panel, Board and Software Change / Upgrade(P/N:98881800x)” for details. GN3TR chassis is the same as GN1T chassis basically. 1:Download USB image and unzip file. 2: copy unzip file to USB memory root folder. 3: USB memory insert TV.
TROUBLE SHOOTING TRIAGE Confirm the symptom from the customer. Select that symptom from the chart. Bring all the boards and cables listed for that symptom. Follow the troubleshooting charts in the technical guides to isolate the board. Chart Color Code. RED DOT: Most likely defective part BLUE TRIANGLE: Secondary possible defective part BLACK TEXT: Board that may correct the symptom...
TROUBLE SHOOTING FLOW 1-1. NO POWER WITH G* BOARD No Power Check STBY 3.3V Replace C518 Between G* board to G* board near CN400 B* board Harness on B* board Harness B* board u-Com Failure DDCON/LDO Main Device Failure XBR-55/65X930E, 75X940E...
Page 20
TROUBLE SHOOTING FLOW 1-1. NO POWER WITH AC-ADP No Power (Both side are No power.) AC Adaptor Check POWER_MAIN (Only single side is 19.5V or 24V.) Replace Check C409 Between JK* board to F9000 F9000 near CN400 B* board Harness On JK* board on B* board (Both side are...
Page 21
TROUBLE SHOOTING FLOW 1-2. NO POWER U-COM FAILURE START Check 12V_MON Check +12V_MAIN Line Check VDD Check +3.3V_STBY LIne (C521, CN400 #14pin) R446 Voltage. (G board or JK board). C506 Voltage. And (only for AC-ADP model) Is the voltage >2.6V? Is the voltage >3.0V? 3.3V_DDCON (IC403) (only for AC-ADP model)
Page 22
TROUBLE SHOOTING FLOW 1-2. NO POWER U-COM FAILURE Previous page Check P_ON_#2 CL417 or P-on ucom #pin13 Change IC401 is >3.0V? Check P_ON_HL CL414 or P-on ucom #pin18 Change IC401 is >3.0V? Check ORESETB CL416 or P-on ucom #pin14 Change IC401 Is the voltage >3.0V? Check X_SYSTEM_RST CL412 or P-on ucom #pin20...
Page 23
TROUBLE SHOOTING FLOW 1-3. NO POWER DDCON/LDO DDCONs CHECK ON JK* START Check fuse F9001 Change Fuse Is fuse OK? (Both side are No power.) AC Adaptor Check Vcc voltage Check C9023 F9000 F9000 Is voltage >18V? On JK* board (Only single side is 19.5V or 24V.) (Both side are...
Page 24
TROUBLE SHOOTING FLOW 1-3. NO POWER DDCON/LDO DDCON CHECK START Check IC402 Vcc voltage Check Vcc voltage Check C423 C602 D600 Change D600 Is voltage >12V? Is voltage >3V? Is diode alive? Check +3.3V_STBY. G* board or IC403 Check Vcc voltage Check C602 D601...
Page 25
TROUBLE SHOOTING FLOW 1-3. NO POWER DDCON/LDO DDCONs CHECK LDOs CHECK START START Check fuse Check +3.3V_DDC_OUT F4xx / F40xx/F6xx Change Fuse Check Vcc voltage DDCON (IC403) Is fuse OK? C4xxx or C6xx Is voltage >3V? +3.3V_STBY (G* board) 1) Check POWER_ON P-on ucom #pin10 Check Vcc voltage (Refer to No Power U-Com Failure) C4xx / C40xx/C6xx...
Page 26
TROUBLE SHOOTING FLOW 2-1. LED BLINKING 2X (MAIN POWER ERROR) LED 2X blinking Check “+12V_MAIN” G board at pin 11/13 of CN400 JK board on B* board, AC Adaptor Voltage > 13.2V ? BMKS / BMKP board XBR-55/65X930E, 75X940E...
Page 27
TROUBLE SHOOTING FLOW 2-2. LED BLINKING 3X (DC ALERT AND AUDIO ERROR) DC_ALERT AUDIO ERROR 3-times blinking 3-times blinking (Audio Error) (DC Alert) Power Off Check Go to No Sound (Power Off Check) Check “POWER_MAIN” Check “+5.0V_VBUS” at pin 17/19 of CN400 on B* board, at C431 on B* board Other flows...
Page 28
TROUBLE SHOOTING FLOW 2-3. LED BLINKING 4X (LED VOLTAGE ERROR AND BCM ERROR) LED VOLTAGE ERROR 4-times blinking (LED Voltage) High Check “LD_ERR_DET” Voltage Replace LD board Panel at CL4458 on BMKP board BMKP board LD board BCM ERROR 4-times blinking (BCM Error) Check “LD_RDY”...
Page 29
TROUBLE SHOOTING FLOW 2-4. LED BLINKING 5X (PANEL ID READ ERROR) 5-times blinking Check Replace “+12.5V_TCON” G/JK board G/JK board at C400 on BMKP Replace the Harness Symptom improve Between G/JK board Harness and BMKP Symptom improve Replace V-By-One FFC the V-By-One FFC Symptom improve Replace...
Page 30
TROUBLE SHOOTING FLOW 2-5. LED BLINKING 6X (BACKLIGHT ERROR) 6-times blinking Harness / Connection Symptom Check Voltage of Check High broken Improvement Replace “BL_ERR_DET” harness/connection Harness harness at CL4459 on BMKP G/LD board to BMKP improvement Symptom Harness / LED driver or G board Improvement Connection OK LD board/G board...
Page 31
TROUBLE SHOOTING FLOW 2-6. LED BLINKING 7X (TEMPERATURE ERROR) 2-7. LED BLINKING 8X (4KBE ERROR) 7-times blinking 8-times blinking Setting circumstance is OK? Set to another improvement Replace Temperature, location, etc. Other flows BMKP board Ventilation, etc. Symptom Improvement Replace BMKS/BMKP board, and Aging a few Panel BMKP board...
Page 32
TROUBLE SHOOTING FLOW 3-1. NO SOUND No Sound Without LED 3x Select [External Inputs] AV receiver is connected [BRAVIA Sync Settings] to HDMI in ? [BRAVIA Sync Control] [off] No sound only Go to Analog RF and Digital RF ? NO SOUND ( TUNER) [Speakers] setting is Change the setting to...
Page 33
TROUBLE SHOOTING FLOW 3-2. NO SOUND (POWER OFF CHECK) 3-3. NO SOUND (POWER ON CHECK) PVDD (POWER_AU) voltage is 240W AC Adaptor model : 24.0V Power On Check Power Off Check 200W AC Adaptor model : 19.5V Power Off Check From LED BLINKING 3X From LED BLINKING 3X Built-in power supply model : 12.5V...
Page 34
TROUBLE SHOOTING FLOW 3-4. NO SOUND (AUDIO HP/AUDIO OUT) 3-5. NO SOUND ( TUNER) No Sound with normal picture No Sound Audio HP/Audio out [Headphone] [Sound] Headphone Volume [Headphone/Audio out] Increase Headphone Volume Only RF tuner input? is set to MIN? is set to ? Replace B* board [Audio Out (Fixed)]...
Page 35
TROUBLE SHOOTING FLOW 3-6. NO SOUND (HDMI) No Sound Check the picture Refer to NO PICTURE (HDMI) Does this model have Check the mode Connect Stereo minijack cable between Source and the TV, Analog Audio In And Change “HDMI/DVI Audio Source” to Auto or Analog Audio In. of Source equipment (Stereo minijack)? HDMI...
Page 36
TROUBLE SHOOTING FLOW 4-1. NO PICTURE No Picture BL_ON (L or H): IC401 #7pin (for 4K BMKS/BMKP board) BL_ON:H Check Smart Core Check Replace Got Any Normal Replace LCD Panel Behavior BL_ON the V by One FFC Display? The B board (T-CON) (5x Blinking) on the B board...
Page 37
TROUBLE SHOOTING FLOW 4-2. NO PICTURE (VIDEO 1/VIDEO 2/COMPONENT) VIDEO 1 No Picture Video 1 No Picture Check J2601 Check if input OSD NG (Vpp: 0V) Connection, is GRAY OUT VIDEO_DET OK if it is highlighted At R2631 OK (Vpp: 3.3 V) Detailed check all NG (Vpp: 0V) parts at VIDEO2_DET...
Page 38
TROUBLE SHOOTING FLOW 4-2. NO PICTURE (VIDEO 1/VIDEO 2/COMPONENT) COMPONENT / VIDEO 2 No Picture Component Video 2 No Picture No Picture Check if input OSD NG (Vpp: 0 V) Check J2600 Con Check J2600 Check if input OSD is GRAY OUT NG (Vpp: 0 V) Connection, VIDEO_DET at R2626,...
Page 39
TROUBLE SHOOTING FLOW 4-3. NO PICTURE (TUNER) RF input no picture / noisy picture Notes: I2C I2C line for all tuners except Japan_SKP - Parts for I2C SDA line: R2800, C2803. Check RF source cable Change RF cable and antenna - Parts for I2C SCL line : R2801, C2804.
Page 40
TROUBLE SHOOTING FLOW 4-4. NO PICTURE (TUNER) FOR ANALOG TUNING Analog Tuning For LA-ISDB(BR/AR), LA-T2(COL) and TW only For Other destination Notes: Confirm ANT or Cable connection - Parts for IFOUT_N line : FB2801, C2807, C2826 - Parts for IFOUT_P line : FB2802, C2808, C2825 - Parts for IFAGC line : R2838, C2827 : Insert correct signal in correct terminal.
Page 41
TROUBLE SHOOTING FLOW 4-4. NO PICTURE (TUNER) FOR DIGITAL TUNING 1 Digital Tuning 1 For TW/LA-ISDB-T Notes: - Parts for IFOUT_N line : FB2801, C2807, C2826 - Parts for IFOUT_P line : FB2802, C2808, C2825 - Parts for IFAGC line : R2838, C2827 For NA-ATSC(MX/UC) Confirm ANT or Cable connection...
Page 42
TROUBLE SHOOTING FLOW 4-5. NO PICTURE (HDMI) HDMI1 No Picture Check the below point at All lines Connector side are NG Other Input is OK Check other - Check +5V line Replace HDMI input - Check HPD line CN3603 - Check DDC lines - Check TMDS lines All Inputs are NG TMDS lines...
Page 43
TROUBLE SHOOTING FLOW 4-5. NO PICTURE (HDMI) HDMI2 No Picture Check the below point at All lines Connector side are NG Other Input is OK Check other - Check +5V line Replace - Check HPD line HDMI input CN3600 - Check DDC lines All Inputs are - Check TMDS lines Other TV set...
Page 44
TROUBLE SHOOTING FLOW 4-5. NO PICTURE (HDMI) HDMI3 No Picture Check the below point at All lines Connector side Other Input is OK are NG Check other - Check +5V line Replace HDMI input - Check HPD line CN3601 - Check DDC lines All Inputs - Check TMDS lines are NG...
Page 45
TROUBLE SHOOTING FLOW 4-5. NO PICTURE (HDMI) HDMI4 No Picture Check the below point at All lines are Connector side Other Input is OK - Check +5V line Replace Check other HDMI input - Check HPD line CN3602 - Check DDC lines All Inputs - Check TMDS lines are NG...
Page 46
TROUBLE SHOOTING FLOW 5. KEY SWITCH BUTTONS ERROR Side key buttons error Check harness connection between B*board and switch Harness connection issue module Resistor value [BMKS] Change harness between B* B* board to switch module harness R1108 : 0 [ohm] board to switch module R1049 : 47k [ohm] issue...
Page 47
TROUBLE SHOOTING FLOW 6. IR REMOTE COMMANDER ERROR IR remote commander does not respond Center white LED blinks when Battery of remote commander pushing buttons of remote could be weak. commander at close to IR Change battery. sensor. Check harness connection Harness connection between B*board and Smart issue...
Page 48
TROUBLE SHOOTING FLOW 7. LIGHT SENSOR ERROR Backlight level does not change when ambient light changed Setting is “ON” Check UI setting and make Check harness connection Battery of remote commander sure light sensor setting is between B*board and Smart could be weak.
Page 49
TROUBLE SHOOTING FLOW 8. NETWORK MALFUNCTION ETHERNET (WIRED) [Network Set-up] >[Wired Set-up] on the TV Connection Results Connection Results Connection Results B* board Cable Connection Local Access Internet Access Failed Failed Failed Auto Check Wired Set-up Check cable B* board Proxy setting Local router IP address setting...
Page 50
TROUBLE SHOOTING FLOW 9. NETWORK MALFUNCTION INTERNAL WIRELESS NETWORK MALFUNCTION Wireless Network on the TV Is the Wi-Fi radio Error message or no scan result appear in strength too weak B* board the network setting? or even No signal? Check with another Wi-Fi Access Point Hardware defect suspected module...
Page 51
TROUBLE SHOOTING FLOW 10. BLUETOOTH MALFUNCTION Voice Remote doesn’t work 3D-glasses (Active) doesn’t work Bluetooth Speaker/Headphone/Headset doesn’t work Please refer Voice Remote manual Check BT antenna Home > Settings > 3D-glasses (Active) manual Connection is OK Bluetooth Settings Can read Bluetooth Speaker/Headphone/Headset operation manual Near discoverable Bluetooth Device...
BLOCK DIAGRAMS * depend on destinations. Some control lines are left out. BMKP board * IR In Center Key RGBW LEDs Video signal * CAS/CI DDCs Audio signal L/R Keys Light Sens. Control Bus IR Rx Power * RF Micro Component/ (STM8S103F2U6) LD board...
Page 59
WIRE DRESSING *This page is only the information which shows each rough location. XBR-55X930E XBR-65X930E VA Tape Harness Tie x5 Slide Clamp x0 VA Tape Harness Tie x3 Slide Clamp x0 ・Fix wire • Fix wire • Hold wires ・Fix wire •...
Page 60
PANEL HANDLING ON WORKING TABLE Caution: • Put soft & clean sheet on the table, when you put the Panel. • Be careful there is nothing on the table such as dust, scrap, screw and so on. (Risk of scratches on aluminum frame or screen surface while moving the module.) •...
Page 61
PANEL HANDLING LIFTING UP BOTTOM Shift the panel to hold Bottom side Hold Bottom side (Don’t slip the panel) Lift up Top side BOTTOM Flip up to vertical position Prohibited holding position (Refer to following pages for detail) XBR-55/65X930E, 75X940E...
Page 62
PANEL HANDLING PROHIBITED HOLDING POSITION (55”/65”) <Detail B> Should not grip hole area. Except in case of taking in & taking out panel from packing. <Detail A> In these case, there are space for handling on cushion and they are same position as support rib in hole. Operator definitely can grip only their position in these case.
Page 63
PANEL HANDLING PROHIBITED HOLDING POSITION (75”) <Detail B> <Detail A> Should not grip corner area Should not grip hole area except for center area of hole. Should not grip hole area XBR-55/65X930E, 75X940E...
Page 64
PANEL HANDLING HOLDING ON HORIZONTAL POSITION (55”/65”) Holding Left/Right Edge Pushing FFC (Harness) * Only for 55inch XBR-55/65X930E, 75X940E...
Page 65
PANEL HANDLING HOLDING ON HORIZONTAL POSITION (75”) Should not holding only Left/Right Edge (Both hands) Should not holding around Corner To prevent PANEL deformation To prevent corner gap/step effect risk XBR-55/65X930E, 75X940E...
Page 66
PANEL HANDLING HOLDING ON VERTICAL POSITION & MOVING Moving at Horizontal Condition Moving with Stand Holding only Left/Right Edge Catching Frame by Finger Pushing Display by Finger Move the Panel at Vertical Condition Not-pushing Display by Finger Pushing Display by Finger XBR-55/65X930E, 75X940E...
Page 67
DISASSEMBLY • There are clutch in the yellow frame[ ]. Therefore please be careful in the case of the disassembly or assembly of parts. • [ ] indicates the part to disconnect or remove from the connectors or clampers. 1. XBR-55X930E 1-1.
Page 68
DISASSEMBLY 1. XBR-55X930E 1-2. XBR LOGO NO3.5 (PUC) XBR LOGO NO3.5 (PUC) P/N: 4-692-705-01 1-3. CLAMPER, CABLE S (PUC) CLAMPER, CABLE S (PUC) XBR-55/65X930E, 75X940E...
Page 75
DISASSEMBLY 1. XBR-55X930E 1-10. COVER CENTER TOP(L PUC) COVER CENTER TOP(L PUC) XBR-55/65X930E, 75X940E...
Page 76
DISASSEMBLY 1. XBR-55X930E 1-11. COVER SIDE TOP (L PUC) Screw (SCREW +BVTP 3X10 TYPE2 IT-3) P/N: 7-685-647-79 COVER SIDE TOP (L PUC) XBR-55/65X930E, 75X940E...
Page 77
DISASSEMBLY 1. XBR-55X930E 1-12. LABEL, DC IN (GNT) AND LABEL, UNDER TERMINAL (PUC) AND LABEL, SIDE TERMINAL (PUC) LABEL, SIDE TERMINAL (PUC) LABEL, UNDER TERMINAL (PUC) LABEL, DC IN (GNT) XBR-55/65X930E, 75X940E...
Page 106
DISASSEMBLY 1. XBR-55X930E 1-41. BRACKET, UNDER (PUC) BRACKET, UNDER (PUC) XBR-55/65X930E, 75X940E...
Page 107
DISASSEMBLY 1. XBR-55X930E 1-42. BRACKET, SIDE (PUC) BRACKET, SIDE (PUC) XBR-55/65X930E, 75X940E...
Page 108
DISASSEMBLY 1. XBR-55X930E 1-43. BRACKET, IR IN AND IR Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-55/65X930E, 75X940E...
Page 109
DISASSEMBLY 1. XBR-55X930E 1-43. BRACKET, IR IN AND IR NOTE: BRACKET, IR IN Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-55/65X930E, 75X940E...
DISASSEMBLY 2. XBR-65X930E 2-1. STAND NECK (R) (2L PUC) A AND STAND NECK (L) (2L PUC) A AND STAND BASE (2L PUC) A 4 screws (SCREW, +PSW M5X16) P/N: 2-580-608-01 STAND,NECK (R) (2L PUC) A STAND,NECK (L) (2L PUC) A STAND, BASE (2L PUC) A 4 screws ( SCREW, STAND (SBT)) P/N: 4-692-700-01 XBR-55/65X930E, 75X940E...
Page 120
DISASSEMBLY 2. XBR-65X930E 2-2. XBR LOGO NO3.5 (PUC) XBR LOGO NO3.5 (PUC) P/N: 4-692-705-01 2-3. CLAMPER, CABLE S (PUC) CLAMPER, CABLE S (PUC) XBR-55/65X930E, 75X940E...
Page 121
DISASSEMBLY 2. XBR-65X930E 2-4. CLAMPER, CABLE L (PUC) CLAMPER, CABLE L (PUC) CLAMPER, CABLE L (PUC) XBR-55/65X930E, 75X940E...
Page 122
DISASSEMBLY 2. XBR-65X930E 2-5. COVER SCREW (2L PUC) AND COVER SP L (2L PUC) COVER SCREW (2L PUC) COVER SP L (2L PUC) XBR-55/65X930E, 75X940E...
Page 126
DISASSEMBLY 2. XBR-65X930E 2-9. COVER SIDE TOP (2L PUC) Screw (SCREW +BVTP 3X10 TYPE2 IT-3) P/N: 7-685-647-79 COVER SIDE TOP (2L PUC) XBR-55/65X930E, 75X940E...
Page 127
DISASSEMBLY 2. XBR-65X930E 2-10. LABEL, SIDE TERMINAL (PUC) AND LABEL, UNDER TERMINAL (PUC) LABEL, SIDE TERMINAL (PUC) LABEL, UNDER TERMINAL (PUC) XBR-55/65X930E, 75X940E...
Page 157
DISASSEMBLY 2. XBR-65X930E 2-40. BRACKET, UNDER (PUC) BRACKET, UNDER (PUC) XBR-55/65X930E, 75X940E...
Page 158
DISASSEMBLY 2. XBR-65X930E 2-41. BRACKET, SIDE (PUC) BRACKET, SIDE (PUC) XBR-55/65X930E, 75X940E...
Page 159
DISASSEMBLY 2. XBR-65X930E 2-42. BRACKET, IR IN AND IR Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-55/65X930E, 75X940E...
Page 160
DISASSEMBLY 2. XBR-65X930E 2-42. BRACKET, IR IN AND IR NOTE: BRACKET, IR IN Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-55/65X930E, 75X940E...
DISASSEMBLY 3. XBR-75X940E 3-1. STAND NECK (R) (3L PUC) A AND STAND NECK (L) (3L PUC) A AND STAND BASE (3L PUC) A 4 screws (SCREW, +PSW M5X16) P/N: 2-580-608-01 STAND,NECK (R) (3L PUC) A STAND,NECK (L) (3L PUC) A STAND, BASE (3L PUC) A 4 screws ( SCREW, STAND (SBT)) P/N: 4-692-700-01 XBR-55/65X930E, 75X940E...
Page 170
DISASSEMBLY 3. XBR-75X940E 3-2. XBR LOGO NO3.5 (PUC) XBR LOGO NO3.5 (PUC) P/N: 4-692-705-01 3-3. CLAMPER, CABLE S (PUC) CLAMPER, CABLE S (PUC) XBR-55/65X930E, 75X940E...
Page 171
DISASSEMBLY 3. XBR-75X940E 3-4. CLAMPER, CABLE L (PUC) CLAMPER, CABLE L (PUC) CLAMPER, CABLE L (PUC) XBR-55/65X930E, 75X940E...
Page 173
DISASSEMBLY 3. XBR-75X940E 3-6. COVER SIDE TOP (3L PUC) Screw (SCREW +BVTP 3X10 TYPE2 IT-3) P/N: 7-685-647-79 COVER SIDE TOP (3L PUC) XBR-55/65X930E, 75X940E...
Page 174
DISASSEMBLY 3. XBR-75X940E 3-7. LABEL, SIDE TERMINAL (PUC) AND LABEL, UNDER TERMINAL (PUC) LABEL, SIDE TERMINAL (PUC) LABEL, UNDER TERMINAL (PUC) XBR-55/65X930E, 75X940E...
Page 207
DISASSEMBLY 3. XBR-75X940E 3-39. BRACKET, UNDER (PUC) BRACKET, UNDER (PUC) XBR-55/65X930E, 75X940E...
Page 208
DISASSEMBLY 3. XBR-75X940E 3-40. BRACKET, SIDE (PUC) BRACKET, SIDE (PUC) XBR-55/65X930E, 75X940E...
Page 209
DISASSEMBLY 3. XBR-75X940E 3-41. BRACKET, IR IN AND IR Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-55/65X930E, 75X940E...
Page 210
DISASSEMBLY 3. XBR-75X940E 3-41. BRACKET, IR IN AND IR NOTE: BRACKET, IR IN Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-55/65X930E, 75X940E...
Page 227
EXPLODED VIEWS • Items with no part number and no description are not stocked because they are seldom required for routine service. • The construction parts of an assembled part are indicated with a collation number in the remark column. •...
Page 245
EXPLODED VIEWS 4. SMART CORE (P) REF. No. PART No. DESCRIPTION MARK 4-686-121-02 COVER, TOP (PUC) 4-686-118-01 PANEL, ORNAMENT (PUC) 4-686-119-01 GUIDE, LIGHT (PUC) A-2166-258-A HS5 MOUNT 4-686-120-02 CASE, BOTTOM (PUC) XBR-55/65X930E, 75X940E...
Page 246
EXPLODED VIEWS 5. OTHER PART ACCESSORIES REMOTE COMMANDER (RMF-TX200U) STAND, BASE (L PUC) A STAND,NECK (L) (L PUC) A P/N: 1-493-127-31 P/N: 4-599-940-01 4-599-943-01 STAND, BASE (2L PUC) A STAND,NECK (L) (2L PUC) A P/N: 4-599-941-01 4-599-944-01 STAND,NECK (L) (3L PUC) A STAND, BASE (3L PUC) A 4-599-945-01 P/N: 4-599-942-01...
APPENDIX-1 Voice Remote Control • This remote has the following functions: • Key “MIC” key: Bluetooth • Voice search • Key codes (except “MIC” key) are sent by IR code. You can control all TVs without pairing. • “MIC” key code and voice data are sent by Bluetooth. Voice search function could be used with only the paired TV.
APPENDIX-1 Setting Voice Remote Control To register the Voice Remote Control to the TV 1. Press the HOME button, select [Settings] [Voice Remote Control] [Activate the button] then, follow the on-screen instruction. 2. Prepare Voice Remote Control. 3. Press and hold down the Volume-down key. 4.
APPENDIX-2 Reset vs. Factory Reset Reset: Press and hold down the power button (approx. 5 seconds) on the remote commander until the message “Power off” appears on the TV screen The TV will turn off, and then restart automatically Try a reset when Android TV doesn’t behave properly (e.g., the TV is unresponsive or is stuck on a black screen). Note if you unplug and plug in the power cable, it may have the same effect as a reset.
APPENDIX-3 (KP55) Add cushion to the H frame (6 points) The cushion size 18X11mm h=8mm (CUSHION RC(L PUC) P/N:4-696-018-01) DATAM DATAM The center of the cushion and the positioning boss are the same location. Aline spine and a cushion end. (6 points same) DATAM DATAM DATAM...
APPENDIX-3 (KP65) Add cushion to the H frame (7 points) The cushion size 11X8mm h=8mm (CUSHION RC S(2L PUC) P/N:4-696-015-01) Aline Metal frame and cushions XBR-55/65X930E, 75X940E...
Table of contents F COVER APPENDIX-1 MODEL LIST Voice Remote Control WARNINGS AND CAUTIONS How to use voice search function SAFETY CHECK-OUT Setting Voice Remote Control SELF DIAGNOSIS FUNCTION APPENDIX-2 ADJUSTMENT Reset vs. Factory Reset USB UPDATE APPENDIX-3 TROUBLE SHOOTING (KP55) Add cushion to the H frame (6 points) TRIAGE (KP65) Add cushion to the H frame (7 points)