hit counter script
ABB TZID Operating Instructions Manual
  1. Manuals
  2. Brands
  3. ABB Manuals
  4. Valve Positioners
  5. TZID
  6. Operating instructions manual
ABB TZID Operating Instructions Manual

ABB TZID Operating Instructions Manual

Electro-pneumatic positioner
Hide thumbs
Table of Contents

Advertisement

Quick Links

Electro-Pneumatic Positioner
Operating Instructions
TZID
42/18 54 EN
Software Revision 5.07

Advertisement

Table of Contents
loading

Related Manuals for ABB TZID

Summary of Contents for ABB TZID

  • Page 1 Electro-Pneumatic Positioner Operating Instructions TZID 42/18 54 EN Software Revision 5.07...
  • Page 2 Tel: +49 551 905-534 Fax: +49 551 905-555 CCC-support.deapr@de.abb.com © Copyright 2006 by ABB Automation Products GmbH Modifications reserved This document is subject to copyright. It is intended to help the user operate the equipment safely and efficiently. The content may not be copied or reprodcued either in part or in full without the prior consent of the copyright owner.

  • Page 3: Table Of Contents

    Mounting to rotary actuators ................. 16 Pneumatic connection ...................21 3.2.1 Safety instructions ..................21 3.2.2 Making the pneumatic connection ............... 21 Electrical connection....................23 3.3.1 Safety instructions ..................23 3.3.2 General installation instructions..............23 3.3.3 Overview....................... 24 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 4 Checking/replacing the filter regulator..............36 Checking the air filter in the positioner ...............37 Replacing the pneumatic output unit ..............38 6 Technical data ......................39 Basic model......................39 Options ........................43 7 Certificates ........................45 Appendix A: Error codes ....................64 Electro-pneumatic positioner TZID 42/18-54 EN...

  • Page 5: Important Information

    If the information in this document is insufficient in any situation, please contact our service de- partment, who will be happy to help you. Please read this document carefully before installation and commissioning. 42/18-54 EN Electro-pneumatic positioner TZID...

  • Page 6: Safety Summary

    The regulations, standards and directives referred to in this manual are applicable in Ger- many. When using the TZID positioner outside the German jurisdiction, the relevant reg- ulations, standards and directives applicable in the country where the device is used must be observed.

  • Page 7: Device-Specific Safety Instructions

    WARNING • The TZID rotating shaft can only be rotated in the direction of the indi- cating arrow on the shaft. There are no mechanical stops to limit the actuator movement. Improper mounting can damage the device and void warranty.

  • Page 8: Electrical Safety

    (SELV) according to EN 60 950. Electromagnetic interference • Do not lay signal lines close to power lines. Power lines produce inter- ference in their near vicinity, which may affect measured value trans- NOTICE mission on the signal line. Electro-pneumatic positioner TZID 42/18-54 EN...

  • Page 9: Explosion Protection

    Type plates indicating the degree of explosion protection 1.4 Correct use The TZID positioner is an electro-pneumatic positioner for pneumatic final control ele- ments. It is designed for being attached to linear and rotary actuators following the instructions in this manual. The positioner may be used only for the applications listed in these operating instructions or in the data sheet 18-0.20 EN.

  • Page 10: Qualified Personnel

    18-0.20 EN. 2.2 CE compliance information We declare that we are the manufacturer of the TZID positioner and that the product con- forms with the EMC Directive 89/336/CEE as of May 1989 and meets the requirements of the following standards: •...

  • Page 11: Installing And Commissioning

    Installing and commissioning 3.1 Mechanical mounting 3.1.1 General • No further steps are required if the TZID positioner is delivered mounted to an actuator. • These operating instructions describe how to mount the positioner to IMPORTANT linear actuators in accordance with DIN/IEC 534 (lateral attachment to NAMUR) and to rotary actuators in accordance with VDI/VDE 3845.

  • Page 12: Operating Conditions At The Installation Site

    3.1.2 Operating conditions at the installation site Before installing check to ensure that the specifications in terms of safety and control applicable to the TZID positioner will not be exceeded at the installation site of the actuator or final control element.

  • Page 13: Mounting To Linear Actuators

    All other items are part of the mounting kit which has to be ordered separately. The TZID positioner comes with the lever (4) already installed. All other items are deliv- ered in a separate package. The lever is available in two lengths: for 10 to 85 mm strokes (standard version) and for strokes 10 to 150 mm (special version, to be ordered sepa- rately).
  • Page 14 Hand-tighten the nuts evenly. Fig. 5 Mounting to columnar yoke Adjust the height of the positioner at the cast iron yoke or the columnar yoke until the lever is horizontal (at visual check) at half valve stroke. IMPORTANT Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 15 A scale on the lever helps you to determine the valve stroke range. Use the lever scale to set the bolt to the appropriate position. A rough adjustment is suffi- cient. The fine adjustment will be done later in the commissioning phase using the Autostroke function. 42/18-54 EN Electro-pneumatic positioner TZID...

  • Page 16: Mounting To Rotary Actuators

    Fig. 7 Mounting to rotary actuators The TZID positioner is mounted to the rotary actuator using a mounting bracket (7), which has to be ordered separately. At the positioner’s back you can find four threaded holes M6 arranged on a 50 mm circle diameter, into which the mounting bracket’s fasten- ing screws (1) are screwed.
  • Page 17 - The TZID rotating shaft can only be rotated in the direction of the indicat- ing arrow on the shaft. There are no mechanical stops to limit the actua- tor movement. Improper mounting can damage the device and void warranty.
  • Page 18 Mounting TZID shifted by 90° to an actuator turning counterclockwise • Undo the setscrews on the shaft adapter. • Shift the adapter by 90°, as Setscrew with shown in Fig. 10. flat point • Re-fasten the setscrews. Setscrew with cone point Fig.
  • Page 19 Mounting TZID in parallel with an actuator turning clockwise • Undo the setscrews on the shaft adapter. • Shift the adapter by 90°, as Setscrew with shown in Fig. 12. flat point • Re-fasten the setscrews. Setscrew with cone point Fig.
  • Page 20 Mounting TZID shifted by 90° to an actuator turning clockwise The TZID positioner is prepared for this type of mounting when it is delivered. No adapter settings are required. Setscrew with cone point Setscrew with flat point Fig. 14 Adapter position (factory setting) •...

  • Page 21: Pneumatic Connection

    The amount of supply pressure has to be matched to the working pressure necessary for the actuation. The positioner's operating range is between 1.4 and 6 bar. 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 22 A pressure gauge block is available for indicating the supply air pressure and output pressure. Fasten the pressure gauge block to the side of the TZID positioner. Make sure that the O-ring seals are positioned properly to ensure tight fitting.

  • Page 23: Electrical Connection

    Electromagnetic interference • Do not lay signal lines close to power lines. Power lines produce inter- ference in their near vicinity, which may affect measured value trans- mission on the signal line. 42/18-54 EN Electro-pneumatic positioner TZID...

  • Page 24: Overview

    Two threaded bore holes 1/2 - 14 NPT or M20 x 1.5 are available on the right-hand side as the cable entry into the case. One is equipped with a cable gland and in the other a pipe plug is mounted. In its standard version the TZID positioner is delivered with the cable gland already installed.
  • Page 25 L= <1mA; H= >2mA feedback 5 … 11V DC 4...20 mA Analog feedback 10 V ...30 V SW 1 Digital feedback SW 2 24 V DC Analog 4...20 mA input Fig. 20 Terminal assignment 42/18-54 EN Electro-pneumatic positioner TZID...

  • Page 26: Commissioning

    Any adjustment that goes beyond this scope requires the method described below. Commissioning the positioner remotely via a PC with special TZID software Commissioning through the PC is done via the communication port and a special adapter.

  • Page 27: Adjusting The Tolerance Band

    3.4.4 Setting parameters for current operation Normally, “Controlling adaptive“ at operating level 1 is selected for current operation. It is only necessary to select “Controlling fixed“ if the positioner is working unstable in adap- tive mode. 42/18-54 EN Electro-pneumatic positioner TZID...

  • Page 28: Adjusting Low And High Alarm Limits (Supplementary Modules For Digital Feedback)

    Control lug within proximity switch -> state 1 (control current > 3 mA) The TZID positioner has two screws for alarm limit adjustment (see Fig. 21). The screws are protected against unwanted turning. To adjust the alarm limits, push in the adjust- ment screws with a screw driver to enable snapping in.

  • Page 29: Restoring The Factory Setting

    Determine and save the deadband (smallest possible value). Determine and save PD control parameters for rapid control of deviations > deadband. 50 -120 Determine and save PID control parameters for fine adjustment of control deviations < deadband. Autostroke completed. 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 30 This list applies to a full Autostroke. When using a PC with TZID software, you can also execute a partial Autostroke, as listed below: • Stops only (steps 10 to 32/200) • Parameters only (steps 40 to 120/200) • Zero only (refer to the list below for the steps and their meaning...

  • Page 31: Display And Operator Panel

    Display and operator panel The TZID positioner’s display and operator panel is accommodated in the hinged cover (siehe Fig. 22), requiring that the case is opened for operation. Operating mode Display Controlling, adaptive Controlling, fixed Manual control up/down Setting of switches...

  • Page 32: Operating Level 1

    4.1 Operating level 1 When an input signal > 3.6 mA is applied, the positioner starts up at operating level 1. Four operating modes can be selected through manual control. TZID has a rotary switch with positions 0, 1, 2 and 3.

  • Page 33: Operating Level 2

    The arrow indicates that a change-over to operating level 2 is in progress. If the positioner was working in the mode “Controlling adaptive”, the newly deter- mined values are saved. This is indicated by the characters “EE” shown on the dis- play. 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 34 IMPORTANT - If unpermissible values are determined, the Autostroke is automatically aborted and an error code is shown by the display (see Appendix) When this mode is called up, “2.0” is shown in the display. Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 35 “no save”. Selecting “save non-volatile will save all parameters permanently, even if the settings have been made in differ- IMPORTANT ent modes. If, however, you choose “no save”, none of the parameter settings made will be saved. 42/18-54 EN Electro-pneumatic positioner TZID...

  • Page 36: Maintenance

    If you should modify or manipulate the electronics of a positioner without explosion protection, the positioner's warranty will expire immediately. IMPORTANT The TZID positioner is virtually maintenance-free. We recommend to check the control position periodically for conformity with the toler- ance limit.

  • Page 37: Checking The Air Filter In The Positioner

    3. Remove the filter element using tweezers and check the degree of pollution. Replace the filter element if required. Spare filter elements can be ordered from ABB under catalog number 7942511. 4. Insert the filter. 5. Fasten the screw plug again.

  • Page 38: Replacing The Pneumatic Output Unit

    5. Re-insert the Torx-head screws and torque them to 350 Ncm (31 in-lbs). 6. Connect the plug. Make sure that the plug snaps in properly. The connector is protected against polarity reversal. 7. Switch on compressed air supply. Electro-pneumatic positioner TZID 42/18-54 EN...

  • Page 39: Technical Data

    Can be adjusted separately for each direction as a 0...200 second ramp Time-out monitoring Range 0...200 sec (monitoring parameter for control until the deviation reaches the tolerance band) Travel limit Min. and max. limits, freely configurable within 0...100 % of total travel 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 40 Meets the requirements of the EMC Directive 89/336/EEC as of May 1989 CE Mark Meets the EC regulation for the CE conformity mark Communication port Connector for LKS (local communication interface) adapter (standard) FSK module for frequency-modulated tapping (optional) Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 41 CL I, Div. 1, Grp. A-B-C-D CL II, Div. 1, Grp. E-F-G CL III, Div. 1 Non-incendive; Enclosure 4X, max. 85°C CL I, Div. 2, Grp. A-B-C-D CL II, Div. 2, Grp. E-F-G CL III 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 42 NOTICE: Do not expose the terminals to strain! Cable entry: Threades holes (depending on model and order) 1/2-14 NPT or M20 x 1,5 TZID is delivered with the cable gland already installed. Pneumatic connections Threaded holes G 1/4 or 1/4-18 NPT Weight 2.9 kg (TZID with aluminum case)

  • Page 43: Options

    SJ2-SN (NC) SJ2-S1N (NO) When using proximity switch type SJ2-S1N (NO) the TZIDC positioner may be exposed to an ambient temperature of -25 °C ... +85 °C, only. CAUTION 1. ATEX EEx ia IIC T1...T6 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 44 0...10 bar/0...140 psi Output pressure range 0...10 bar/0...140 psi 0..4 bar/0..60 psi With connection block and attachment material for TZID Connection block made of aluminum varnished black or of stainless steel. Filter regulator with attachment material All-metal version, brass, varnished black Bronze filter element, 40 µm, with condensate drain...

  • Page 45: Certificates

    Certificates 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 46 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 47 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 48 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 49 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 50 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 51 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 52 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 53 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 54 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 55 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 56 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 57 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 58 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 59 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 60 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 61 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 62 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 63 42/18-54 EN Electro-pneumatic positioner TZID...

  • Page 64: Appendix A: Error Codes

    Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 65 42/18-54 EN Electro-pneumatic positioner TZID...
  • Page 66 Electro-pneumatic positioner TZID 42/18-54 EN...
  • Page 67 ABB. improvement and the right is reserved to modify the information contained herein without notice. ABB has Sales & Customer Support expertise in over 100 countries worldwide. Printed in the Fed. Rep. of Germany (03.06) www.abb.com ©...

Table of Contents