hit counter script
Sony XDCAM PDW-HD1200 Installation Manual
Sony XDCAM PDW-HD1200 Installation Manual

Sony XDCAM PDW-HD1200 Installation Manual

Professional disc recorder
Hide thumbs Also See for XDCAM PDW-HD1200:

Advertisement

Quick Links

PROFESSIONAL DISC RECORDER
PDW-HD1200
INSTALLATION MANUAL
1st Edition

Advertisement

Table of Contents
loading

Summary of Contents for Sony XDCAM PDW-HD1200

  • Page 1 PROFESSIONAL DISC RECORDER PDW-HD1200 INSTALLATION MANUAL 1st Edition...
  • Page 2 ! 警告 このマニュアルは,サービス専用です。 お客様が,このマニュアルに記載された設置や保守,点検,修理などを行うと感電や火災, 人身事故につながることがあります。 危険をさけるため,サービストレーニングを受けた技術者のみご使用ください。 ! WARNING This manual is intended for qualifi ed service personnel only. To reduce the risk of electric shock, fi re or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualifi ed to do so. Refer all servicing to qualifi...
  • Page 3 FÖRSIKTIGHET! 注意 Fara för explosion vid felaktigt placerat batteri. 指定以外の電池に交換すると, 破裂する危険があります。 Byt endast mot samma eller likvärdig typ av batteri, 必ず指定の電池に交換してください。 enligt tillverkarens rekommendationer. 使用済みの電池は,国または地域の法令に従って När du kasserar batteriet ska du följa rådande lagar 処理してください。 för regionen eller landet. CAUTION PAS PÅ...
  • Page 4 Laser Diode Properties Wavelength : 400 to 410 nm GEFAHR Emission duration : Continuous Laser output power : 135 mW (max. of pulse peak.) Bei geöffnetem Laufwerk und beschädigter oder 65 mW (max. of CW) deaktivierter Verriegelung tritt ein unsichtbarer Standard : IEC60825-1 (2001) Laserstrahl aus.
  • Page 5: Table Of Contents

    Table of Contents Manual Structure Purpose of this manual ............3 (E) Related manuals ..............3 (E) Trademarks ................3 (E) 1. Installation 1-1. Installation Procedure ..........1-1 (E) 1-2. Supplied Accessories ..........1-1 (E) 1-3. Operating Conditions ..........1-2 (E) 1-4. Power Supply ............1-3 (E) 1-5.
  • Page 7: Manual Structure

    For obtaining, contact your local Sony Sales Offi ce/Service Center. . Maintenance Manual volume 2 (Available on request) This manual describes detailed parts list, block diagrams, schematic diagrams, and board layouts required for parts-level service.
  • Page 9: Installation

    Section 1 Installation 1-1. Installation Procedure Installation procedure of this unit is shown on the following fl owchart. Refer to each section about detail of each fl ow. The operation manual is also required to do *-marked fl ow. Start 1-3.
  • Page 10: Operating Conditions

    1-3. Operating Conditions Do not block an air vent. If ventilation is not enough, the unit may be damaged due to increase of the internal temperature of the unit. . Do not shove the unit into a cramped place with poor ventilation. .
  • Page 11: Power Supply

    1-4. Power Supply The unit works with three types of power supply: AC, DC, and a battery. When repairing or checking the unit, using AC power is recommended. Power voltage: 100 to 240 V AC 11 to 17 V DC Power consumption: AC: 65 W DC: 55 W When using the battery, check the remaining amount with the indicator on the side of the battery.
  • Page 12: Installation Space

    1-5. Installation Space 1-5-1. Outside Dimensions 373.3 396.4 Unit : mm 1-4 (E) PDW-HD1200...
  • Page 13: Notes On Installation

    1-5-2. Notes on Installation To avoid an injury, do not install the unit on rickety table. Ventilation and Installation Space for Servicing . Do not block the air exhaust sections (rear panel) and the air vent (bottom of front side and both the right and left sides).
  • Page 14: Rack Mounting

    1-5-3. Rack Mounting Notes on Rack Mounting . A rise in temperature inside the rack due to a residual heat by neighboring units will bad effects on the unit. Check that the temperature inside the rack is within the range of specifi ed operating temperature of the unit.
  • Page 15: Connectors/Cables

    1-6. Connectors/Cables When external cables are connected to the connectors of this unit, the hardware listed below (or equiva- lents) must be used: Panel indication Connection connector (Sony P/N) Connection cable (Sony P/N) Plug, BNC, 75 Z REF. VIDEO INPUT...
  • Page 16: Signal Inputs And Outputs

    1-7. Signal Inputs and Outputs ANALOG AUDIO INPUT ANALOG AUDIO OUTPUT AUDIO MONITOR SD/HDSDI COMPOSITE OUTPUT REF . VIDEO INPUT HDSDI OUTPUT SDSDI OUTPU INPUT TIME CODE Communications connectors D-SUB 9P connector x1 (RS-422A interface) REMOTE (9P) Remote control S400 (i.LINK) 6P, Conform to IEEE1394, Correspond to S400 RJ-45 8P modular jack (NETWORK)
  • Page 17 Output connectors BNC x1 SDSDI OUTPUT 1 Component digital (270 Mbits/s) SMPTE 259M/ITU-R BT.656 BNC x1 (Character superimpose enabled) SDSDI OUTPUT 2 (SUPER) Component digital (270 Mbits/s) SMPTE 259M/ITU-R BT.656 BNC x1 COMPOSITE OUTPUT 1 Analog composite video 1.0 V p-p, 75 Z, negative sync BNC x1 (Character superimpose enabled) COMPOSITE OUTPUT 2 (SUPER)
  • Page 18 9 REMOTE (9P) : 9-pin (female) !- ANALOG AUDIO INPUT : 3-pin (female) ![ ANALOG AUDIO OUTPUT : 3-pin (male) !] AUDIO MONITOR OUTPUT : 3-pin (male) Male Female (External View) Pin No. Signal RM TX (_) (Output) (External View) (External View) RM RX (+) (Input) Pin No.
  • Page 19: Settings After Installation

    1-8. Settings after Installation 8 MAINTENANCE For the settings after installation, refer to the operation manual. (External View) Pin No. Signal USB1_VBUS USB1_D_ USB1_D+ USB2_VBUS USB2_D_ USB2_D+ !\ S400 (i.LINK) : (6-pin) 2 4 6 1 3 5 (External View) Pin No.
  • Page 21 : The material contained in this manual consists of Check the metal trim, “metallized” knobs, information that is the property of Sony Corporation. screws, and all other exposed metal parts for AC Sony Corporation expressly prohibits the duplication leakage.
  • Page 22 PDW-HD1200 (CN) Printed in Japan Sony Corporation PDW-HD1200 (SY) J, E 2012. 6 08 4-427-660-01 ©2012...

Table of Contents