Advertisement
Available languages
Available languages
Quick Links
3-276-523-11(1)
RM-V210
Remote Commander
Operating Instructions
Manual de instrucciones (parte posterior)
© 2007 Sony Corporation
Printed in China
English
Installing the Batteries
For the customers in the U.S.A.
Before replacing the batteries, have new ones ready beforehand.
WARNING
Slide open the battery compartment and insert two size AA (R6)
This equipment has been tested and found to comply with the limits
batteries (not supplied).
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Be sure to line up the + and – on the batteries with the + and – on the
These limits are designed to provide reasonable protection against
battery compartment.
harmful interference in a residential installation. This equipment
1
2
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
When to replace the batteries
• Increase the separation between the equipment and receiver.
Under normal conditions, batteries will last up to one year. If the
• Connect the equipment into an outlet on a circuit different from
Commander does not operate properly, the batteries might be worn
that to which the receiver is connected.
out. Replace the batteries with new ones.
• Consult the dealer or an experienced radio/TV technician for help.
Notes
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
• Replace both batteries with new ones.
equipment.
• Do not take more than 3 minutes to replace the batteries; otherwise,
your setting of the code numbers will be erased.
Setting Up the Remote Commander
Notes on Batteries
• Do not mix old batteries with new ones or mix different types of
About Presetting the Commander
batteries together.
The Commander is preset at the factory to operate Sony brand
• If the electrolyte inside the battery should leak, wipe the
components.
contaminated area of the battery compartment with a cloth and
If you're using the Commander with a Sony component, you won't
replace the old batteries with new ones. To prevent the electrolyte
need to preset the Commander before you start using it.
from leaking, remove the batteries when you plan not to use the
To set up the Commander to use with other (non-Sony)
Commander for a long period of time.
manufacturers' components, or to use with a component that is not
preset at the factory, you'll need to follow the instructions in this
manual to preset the Commander with the correct code number for
your components. (See the supplied "Component Code Numbers"
also).
Component that can be preset
Button
Factory setting
TV
TV
Sony TV
VCR/Cable box/Digital satellite
VCR
Sony VHS VCR
receiver/DVD/TV/Digital video
CBL
Sony Cable box
recorder/DVD Home Theater
DVD
Sony DVD player
Notes
• The Commander can be set up to operate only one component per
button – unless their code numbers happen to be the same. For
example, you cannot set up the Commander to operate a Sony TV
and a Panasonic TV simultaneously (because they use different
code numbers).
• You may not be able to operate even a Sony brand component with
the factory presetting. In such a case, follow the procedure in
"Setting the Code."
Setting the Code
Searching for the Correct Code
Follow the steps 1 and 2 below for each component you plan to use
You can find a code number available for a
with the Commander.
1
component that doesn't have one in the
3
supplied "Component code numbers."
SET
POWER
2
Step 1: Entering the Code Number
TV
VCR
CBL
DVD
Before starting the Search function
1
2
3
2
1 See the supplied "Component code
Set each component to the following status so
4
5
6
SET
POWER
that the Search function works effectively.
7
8
9
numbers", and find the four-digit code
3
0
4
TV
VCR
CBL
DVD
TV, DVD Home Theater: Power-on
ENTER
number for the desired component.
VOL
CH
INPUT
1
2
3
Other components: Power-off
If more than one code number is listed, use
4
5
6
4
PIP
3
the number that's listed first.
7
8
9
* If any of these components are assigned to any
SLEEP
For example, if you're setting up a Sony
5
INFO
0
ENTER
of the Component Select buttons, you can set a
MUTING
RECALL
TV, you would use the code number 8201.
VOL
INPUT
CH
component code using the Search function.
If your component isn't listed, see
PIP
1 Press SET more than two seconds. The SET indicator lights up.
"Searching for the Correct Code."
SLEEP
INFO
2 Press the Component Select button for the desired component.
MUTING
RECALL
The SET indicator lights up.
2 Press SET more than two
seconds.
SET
SET
3 Press CH + or CH – and POWER in turn until the component
The SET indicator lights up.
reacts as follows:
3 Press the button of the
TV, DVD Home Theater: Powers off
component that you want to
Other components: Powers on
SET
set up.
TV
VCR
CBL
DVD
The SET indicator lights up.
Press CH + to go to the next code number.
4 Press the Number buttons to enter the four-digit
Press CH – to go back to the previous code number.
component code number.
The SET indicator flashes once after the numbers have turned one
cycle.
ENTER
5 Press ENTER. The SET indicator turns off. If the SET
One cycle means, for example, that the commander finishes
indicator flashes five times before lighting up, it
searching all the component code numbers allocated to the
means that the setup is incomplete. Confirm the
component.
component code number and start over from Step 4.
4 Press ENTER.
If the code setting is not finished properly
The SET indicator and the Component button turn off.
If you do not input anything into the Commander within 20 seconds
If the SET indicator flashes five times before turning off, it means
between each step, or if you press SET while setting the component
that the setup is incomplete. Start over from Step 3.
code, the setup procedure will be canceled.
If the component does not operate properly, repeat steps 1 to 4 and
Start over from Step 2.
search for another code.
If you still cannot get the Commander to work properly, see
Step 2: Checking if the Code Number Works
"Troubleshooting."
1 Power on the component you want to set up.
2 Aim the Remote Commander at the component and press a button
Operating a Component
to check if that button works.
For example, press the POWER button to see if it works on your
1 Press the button of the desired component on the Commander.
component .
3 Check that the other buttons of the Commander is operating the
TV
VCR
CBL
DVD
corresponding functions of the component.
2 Point the Commander directly at the component.
3 Press the button for the function you want to use.
You can write down the code number on the label inside the
battery compartment lid.
See "Remote Button Descriptions" for complete descriptions of the
buttons on the Commander.
If the Commander Doesn't Seem to Be Working...
Notes on Using the Remote Commander
• First, try repeating these setup procedures using the other codes
listed for your component (see the supplied "Component Code
Basically, use this Commander in the same way as the Commanders
Numbers").
supplied with your components.
• Using this Commander will not increase the functions of your
• If – after trying all the codes listed for your component – you still
components. The functions of the Commander are limited to the
cannot get the Commander to work properly, try the search
functions of the components themselves. For example, if your TV
method described in "Searching for the Correct Code."
does not have a MUTING function, MUTING on this Commander
will not function with your TV.
• Some functions of the component may not work with this
Commander.
• If your cable box can control volume, be sure to set its volume
switch to a medium position. If the volume on the cable box is
turned down completely, you will not be able to adjust your TV's
volume with the Commander.
Operating a DVR (Digital video recorder)
Remote Button Descriptions
2 To change the input mode.
ws D: (*Live TV)
3 and qd
To bring up Master Guide.
To change the channel.
A: (*REPLAY)
SET indicator
General
For example, to change to
To replay.
SET
POWER
1 To set up the Commander,
channel 5, press 0 and 5 (or,
Or to go into REC/REVIEW
TV
VCR
CBL
DVD
press SET more than two
press 5 and ENTER).
mode during play. (After about
1
2
3
8 To turn on the display.
5-second rewind, replay
seconds.
4
5
6
9 To bring up Master Guide.
begins.)
6 Volume up: +
7
8
9
q; To clear the setting.
wd PAGE+ : (*THUMBS+)
Volume down: –
0
ENTER
To exit the setting menu.
To select the desired recorded
VOL
CH
7 To mute the volume on a TV
INPUT
qg CH+: Channel up .
program.
PIP
or a DVD Home Theater.
(*PAGE+) Page up.
(It is necessary to have
SLEEP
qa To turn on and off the power
CH–: Channel down.
recorded the desired program.)
INFO
of the selected component.
MUTING
RECALL
(*PAGE–) Page down.
PAGE– : (*THUMBS–)
A
B
C
D
qs Component select buttons.
qh To operate JUMP or
To select the desired recorded
PAGE
GUIDE
MENU
Press to select a component to
CHANNEL RETURN
program.
operate.
LIST
FAV
qj To call up "Tivo" menu.
(It is necessary to have
OK
qk To call up the MENU display.
recorded the desired program.)
EXIT
TOOLS
ql To move the cursor upward,
wf (*LIST)
downward, to the left, to the
To call up the title of the
right or to enter the selection.
recorded program.
wa N:
To play.
m:
To rewind.
M:
To fast-forward.
zREC: To record, press N
while pressing zREC.
x:
To stop.
X:
To pause.
About tactile dots
.: To proceed to the
The number 5 button, the N button and CH+ each have a tactile dot for
previous location.
convenient use.
>:
To proceed to the next
Note on the VOL+/- and MUTING buttons
location.
The Commander controls or mutes the TV's volume when you select a visual
:
To operate " Flash –."
component. The Commander outputs the signals to control or to mute a TV or
:
To operate " Flash +."
DVD Home Theater's own volume when you have set one of these
components.
*
This key corresponds to Tivo service or the replay service. Refer to its
instruction manual for details.
Operating a TV
Operating a cable box
2 To change the input mode.
w; To call up the option menu.
3, 4 and qd
wa To select TV input source.
2 To change the input mode.
wa N:
To play.
To change the channel. For
ws A: VIDEO 1
3, 4 and qd
m:
To rewind.
example, to change to channel
B: VIDEO 2
To change the channel
M:
To fast-forward.
5, press 0 and 5 (or press 5 and
C: VIDEO 3
(for example, to change to
zREC: To record, press N
ENTER).
D: VIDEO 4
channel 5, press 0 and 5, or
while pressing zREC.
8 To display the current channel
.: VIDEO 5
press 5 and ENTER).
x:
To stop.
:
VIDEO 6
on TV.
8 To turn on the display.
X:
To pause.
:
VIDEO 7
9 To bring up Master Guide.
.: To proceed to the
9 To switch the EPG display to
>:
VIDEO 8
q; To exit the menu.
previous location.
on/off.
m:
HDMI select
qf To operate the Picture-in-
>:
To proceed to the next
q; To exit the setting menu.
N:
HDMI 1
Picture function.
qg CH+: Channel up.
location.
M:
HDMI 2
qg CH+: Channel up.
CH–: Channel down.
ws A: To operate "A" button.
CH–: Channel down.
zREC: Component video
qh To toggle the current /previous
B: To operate "B" button.
qh To operate JUMP, FLASHBACK
connection select
channel.
C: To operate "C" button.
or CHANNEL RETURN function
x:
Component video
qk To call up the MENU display.
wd PAGE+: Page up.
on the TV.
connection 1
ql To move the cursor upward,
PAGE-: Page down.
qj To operate SLEEP function on
X:
Component video
downward, to the left, to the
wf To call up the title of the
the TV.
connection 2
right, or to enter the selection.
recorded program.
qk To call up the MENU display.
wg To use the "FAVORITE"
wg To use the "FAVORITE"
function.
ql To move the cursor upward,
function.
downward, to the left, to the
right, or to enter the selection.
Notes
• There may be cases you may turn on/off the cable box by pressing CH+ or
Operating a VCR
CH– on the Commander.
• If your cable box can control volume, be sure to set its volume control to a
2 To change the input mode.
medium position. If the volume on the cable box is turned down completely,
8 To expose the on-screen
you will not be able to adjust your TV's volume with the Commander.
display.
qf To switch the antenna output.
qg CH+: Channel up
CH–: Channel down
qh To select a deck.
wa N:
To play.
x:
To stop.
m:
To rewind.
M:
To fast-forward.
zREC: To record, press N
while pressing zREC.
X:
To pause.
Operating a digital satellite receiver
Operating a DVD Home Theater
2 To switch the output of the
2 To change the input mode.
wa N:
To play.
wa N:
To play.
digital satellite receiver to the
m:
To rewind.
3 and qd
m:
To rewind.
TV. (When you connect a TV
M:
To fast-forward.
Number buttons: To set items
M:
To fast-forward.
cable or antenna to the receiver,
zREC: To record, press N
selected on the screen.
zREC: To record, press N
the output switches between a
while pressing zREC.
4 To select numbers 10 and
while pressing zREC.
TV and SAT program.)
x:
To stop.
above.
x:
To stop.
3, 4 and qd
X:
To pause.
6 VOL+: AMP volume up
X:
To pause.
To change the channel. For
.: To proceed to the
VOL–: AMP volume down
.: To proceed to the
example, to change to channel
previous location.
7 AMP volume muting
previous location.
5, press 0 and 5 (or press 5 and
>:
To proceed to the next
8 To show the current play status
>:
To proceed to the next
ENTER).
location.
on the screen.
location.
8 To turn on the display.
:
Replay
9 To change the sound.
:
To operate " Flash –."
9 To bring up the Master Guide.
:
Advance
q; To return to the previous
:
To operate " Flash +."
q; To exit the mode.
ws A: RED button
screen.
ws B: open/ close
qf To call up the DISH menu.
B: GREEN button
qf To switch the subtitle.
A: To call up the setup menu.
qg Channel up: +
C: YELLOW button
qg CH+: Tuner +
C: Disc skip
Channel down: –
D: BLUE button
CH–: Tuner –
D: To display the Top Menu.
qh To tune to the last tuned
wd PAGE+: Page up.
qk To call up the MENU.
wg To call up MEMORY.
station.
PAGE-: Page down.
ql To move the cursor upward,
qj To call up the PVR menu.
wf To call up the title of the
downward, to the left, to the
qk To call up the MENU display.
recorded program.
right, or to enter the selection.
ql To move the cursor upward,
wg To use the "FAVORITE"
w; AMP menu
downward, to the left, to the
function.
right, or to enter the selection.
w; To bring up the Station Index.
Specifications
Operating a DVD
Operable distance
Approx. 7 m (23 ft) (varies depending of the
component of each manufacturer)
2 To change the input mode.
ql To move the cursor upward,
Power requirements
Two size AA (R6) batteries (not supplied)
3 and qd
downward, to the left, to the
Battery life
Approx. 1 year (varies depending on frequency of
Number buttons : To set items
right, or to enter the selection.
button use - up to approx. 300 times per day.)
Dimensions
Approx. 53
220 29 mm (w/h/d)
selected from the screen.
w; To call up the "TOOLS" menu.
(2
1
/
8
3
/
1
3
/
in.)
4 To select numbers 10 and
wa N:
To play.
8
4
16
Mass
Approx. 108 g (3.8 oz.) (not including batteries)
above.
m:
To rewind.
8 To show the current play status
M:
To fast-forward.
Design and specifications are subject to change without notice.
on the screen.
zREC: To record, press N
9 To bring up the Master Guide.
while pressing zREC.
q; To return to the previous
x:
To stop.
The validity of the CE marking is restricted to only those countries
screen.
X:
To pause.
where it is legally enforced, mainly in the countries EEA (European
qd To enter the setting. To set
.: To proceed to the
Economic Area).
items selected from the screen.
previous location.
qf To switch the subtitle.
>:
To proceed to the next
qg CH+: Channel up.
location.
CH–: Channel down.
:
To operate " Flash –."
Troubleshooting
qh To select a deck.
:
To operate " Flash +."
qj To switch the subtitle.
ws B: open/ close
If you have problems setting up or using the Commander:
qk To display the DVD menu.
D: To display the Top Menu.
• When setting up the Commander, carefully go through the procedures
A: To call up the setup menu.
described in "Setting the Code." If the code that's listed first for your
wd PAGE+: To select DVD deck.
component doesn't work, try all the codes for your component - in the order
PAGE-: To select HDD deck.
in which they're listed. If all the codes fail to work (or if your component is
wf To display the title menu.
not listed in this manual), try using the procedures in "Searching for the
Correct Code."
• Check that you're aiming the Commander directly at the component, and that
there are no obstructions between the Commander and the component.
• Make sure the batteries you're using are not worn out, and that they're
inserted correctly.
• Check that the button of the TV, VCR, CBL, or DVD is pressed to choose your
desired component.
• Check that the component has infrared remote capability. For example, if
your component didn't come with a remote commander, it probably isn't
capable of being controlled by a remote commander.
• Should any problem persist, reset the Commander to the factory setting by
pressing the POWER, INPUT and VOL– buttons simultaneously.
For the customers in the U.S.A.
Customer Support Information
If – after you've read through this manual – you still cannot get the
Remote Commander to work properly, call the Sony Customer
Support Helpline at 1-800-822-2217.
DVR (Digital Video Recorder)/
Component code numbers /
DVR (Videograbadora digital)
Números de código de componentes
Tivo
ReplayTV
English
Brand
Code No.
Code No.
DVR (digital video recorder), SAT (digital satellite receiver),
Sony
3201, 3205, 3206
—
Cable box, TV, DVD Home Theater, DVD and VCR
Humax
3202, 0413
—
The following tables show brand names and their corresponding code numbers.
Panasonic
—
3203
Español
Philips
3202, 0412
—
Pioneer
0413
—
DVR (Videograbadora digital), SAT (Sintonizador de recepción vía satélite
ReplayTV
—
3203, 3204
digital), adaptador para cablevisión, Televisor, Sistema de cine doméstico en
Tivo
3201, 3202
—
DVD, DVD (reproductor de discos DVD) y Videograbadora
Toshiba
0413
—
Las tablas que se presentan a continuación muestran las marcas y los números de código
correspondientes.
To set a Component Code (see the instruction manual for details)
Cable box/Adaptadores para cablevisión
Para introducir un código de componente (consulte los detalles en el manual
de instrucciones)
Brand
Code No.
c
c
c
Sony
3101
SET
TV
VCR
CBL
DVD
Code No.
ENTER
ABC
9405
Adelphia
3107, 3110
Advanced Newhouse
3107
Altrio
3107
Americast
3105
Atlantic Broadband
3107
SAT(Digital satellite receiver)/
Bell South
3105
SAT(Sintonizador de recepción vía satélite digital)
Blue Ridge
3107
Brigth House
3107
DirecTV
Dish Network
Digital TV Tuner
Cablevision
3107
Brand
Code No.
Code No.
Code No.
Charter
3107
Comcast
3107
Sony
3001,3011,3012
—
—
Cox
3107
DirecTV
3013, 3017, 3018,
—
—
3019, 3023, 3024
General Instrument
3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,
Dish Network
—
3010, 3014, 3025
—
9022, 9043, 9044
General Electric
3019
—
—
Gnc
3105
Hamlin
9022, 9023, 9024, 9025, 9026
Hitachi
3005
—
—
Illico
3107
Hughes
3004
—
—
Humax
3402
—
—
Jerrold
3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,
9022, 9043, 9044
JVC
—
3010, 3014
—
Memorex
3106
Magnavox
3018
—
—
Motorola
3103, 3110, 3111
Panasonic
3003
—
—
NET
9042
Philips
3018
—
—
Oak
9027, 9028, 9029
Proscan
3002, 3007, 3019
—
—
Pace
3107
RCA
3002, 3007, 3019,
—
—
Panasonic
9019, 9020, 9021
3021
Paragon
3106
Samsung
3017, 3022
—
3404
Sylvania
—
—
3403
Philips
3104
Toshiba
3006
—
—
Pioneer
3107, 9014, 9015
Pulsar
3106
Usdigital
—
—
3401
Regal
9022, 9023, 9024, 9025, 9026
Rodgers
3107
Runco
3106
DVD
Scientific Atlanta
3102, 3107, 3108, 3109, 9009, 9010, 9045, 9046
Seren
3107
Brand
Code No.
Sigecom
3107
Sony
0201, 0202, 0203, 0024, 0030, 0211
Susquehanna
3107
Time Warner
3107
Advent
0048
Tocom
9016, 9017, 9043
Aiwa
0015
Toshiba
3106
Apex
0047
Broksonic
0214
Videotron
3107
Wideopenwest
3105, 3107
Cyber Home
0034, 0035, 0226
Zenith
3105, 3106, 9013
Daewoo
0029
Denon
0002, 0017, 0205
Emerson
0040, 0228
Funai
0220
DVD Home Theater (DVD/Receiver combo)/
GO VIDEO
0042, 0212, 0233
Gpx
0046, 0049
Sistema de cine doméstico en DVD
Humax
0232
(combo de receptor de DVD)
ILO
0227, 0230
Insignia
0042, 0215
Brand
Code No.
JVC
0007, 0208
Kenwood
0050, 0051
Sony
4501, 4502, 4503, 4504, 4505
Bose
4512
LG
0218
Insignia
4515
Magnavox
0225
Marantz
0012
JVC
4507
Panasonic
0205, 0213, 0002
LG
4514, 4516
Nexxtech
4515
Philips
0012, 0221, 0231
Onkyo
4509
Pioneer
0004, 0019, 0021, 0204
Samsung
0014, 0212, 0229
Panasonic
4506
Sharp
4510
Sansui
0214
Yamaha
4511
Sharp
0219
Zenith
4513
Sylvania
0215, 0220
Symphonic
0040, 0041
Terapin
0036
Toshiba
0209
Yamaha
0205
Zenith
0218
Continued on reverse side / Continúa en el reverso
Advertisement
Related Manuals for Sony RM RM-V210T
Summary of Contents for Sony RM RM-V210T
- Page 1 Commander to operate a Sony TV and a Panasonic TV simultaneously (because they use different code numbers). • You may not be able to operate even a Sony brand component with the factory presetting. In such a case, follow the procedure in “Setting the Code.”...
- Page 2 Olympic 1011 Para ajustar el control remoto a fin de utilizarlo con componentes de Minutz 8107 Optimus 1027 otros fabricantes (no Sony), o para usarlo con un componente que no Mitsubishi 8211, 8066 Panasonic 1009, 1011, 1060 Motorola 8104 Pentax 1007, 1008 haya sido preajustado en fábrica, tendrá...