Page 1
Portable Manual iR1018/1019/1022/1023 Series Sep 22 2006...
Page 3
Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition of this manual.
Page 4
Introduction Symbols Used This documentation uses the following symbols to indicate special information: Symbol Description Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning. Indicates an item requiring care to avoid electric shocks. Indicates an item requiring care to avoid combustion (fire). Indicates an item prohibiting disassembly to avoid electric shocks or problems.
Page 5
Introduction The following rules apply throughout this Service Manual: 1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with refer- ence to the timing of operation. In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol , the arrow indicates the direction of the electric signal.
Page 9
Contents 5.1.4.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)> 5.1.4.10 <042: Horizontal scan start position adjustment (when scanning on a document fed from ADF)> ................................31 5.1.4.11 <043: Horizontal scan end position correction ((copy:scanning on ADF)> ......31 5.1.4.12 <044: Horizontal scan end position correction (superfine:scanning on ADF)>......31 5.1.4.13 <045: Horizontal scan end position correction (fine:scanning on ADF)>........31 5.1.4.14 <046: Horizontal scan end position correction (standard:scanning on ADF)>...
Page 10
Contents 5.1.13.6 Roller cleaning mode ((0) ROLLER CLEAN)................52 Chapter 6 Outline of Components 6.1 Clutch/Solenoid ..............................53 6.1.1List of Clutches/Solenoids/Motors/Fans ....................53 6.2 Sensor................................. 54 6.2.1List of Sensors ............................. 54 6.3 Lamps, Heaters, and Others ........................... 55 6.3.1List of Lamps, Heaters, and Others ......................55 6.4 PCBs ...................................
Chapter 1 Chapter 1 Maintenance and Inspection 1.1 Periodically Replaced Parts 1.1.1 Periodically Replaced Parts 0013-1259 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / The machine does not have parts that require periodical replacement. 1.2 Durables and Consumables 1.2.1 Durables 0013-1260...
Chapter 2 Chapter 2 Standards and Adjustments 2.1 Image Adjustments 2.1.1 Image parallelism adjustment 0014-5881 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / 1) Create a test chart, load it in the ADF, and make a copy of it. Rear Test Sheet 10mm...
Chapter 2 2.2 Scanning System 2.3.2 Actions to Take before All Clearing (Backing up the User Data) 2.2.1 Procedure after Replacing the CS 0013-1271 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / 0013-1269 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / After replacing the contact sensor (CS), go through the following steps to...
Chapter 3 Display Detail Code Main Cause/Symptom Countermeasure Code E719 0000 Erroneous communication with card reader (serial communication) - Disconnection from the card reader has been detected since - Check the connectors of the card reader and image processor communication started after confirmation of normal PCB.
Page 19
Chapter 3 Code Name Sensor No. Description 0008 Document edge sensor SR2002 The document edge sensor does not detect paper when the paper has been fed by the delay jam predetermined distance since reception of a pickup request. 0009 Document edge sensor SR2002 The trailing edge of paper is not detected when the paper has been fed by the stationary jam...
Chapter 4 Chapter 4 User Mode Items 4.1 User Mode Items 4.1.1 COMMON SETTINGS 0013-7737 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / MEMO: User modes of the USA model (Copy + Print + Scan + Fax + ADF + Network + PCL) are described. Menus and defaults may vary depending on the destination. For details, refer to the User's Guide.
Page 23
Chapter 4 T-4-1 Additional Functions Available Settings 1.FAVORITES NAME max. 16 characters BUTTONS TEL NUMBER ENTRY max. 120 digits IMAGEQUALITY FINE, PHOTO, SUPER FINE, ULTRA FINE, STANDARD OPTIONAL SETTING OFF(*), ON (ECM (ON(*), OFF), TX SPEED (33600bps(*), 14400bps, 9600bps, 4800bps), INTERNATIONAL (DOMESTIC(*), LONG DISTANCE 1, LONG DISTANCE 2, LONG DISTANCE 3) E-MAIL NAME...
Chapter 4 Additional Functions Available Settings 3.CODED SPD NAME max. 16 characters DIAL TEL NUMBER ENTRY max. 120 digits IMAGEQUALITY FINE(*), PHOTO, SUPER FINE, ULTRA FINE, STANDARD OPTIONAL SETTING OFF, ON (ECM (ON(*), OFF), TX SPEED (33600bps(*), 14400bps, 9600bps, 4800bps), INTERNATIONAL (DOMESTIC(*), LONG DISTANCE 1, LONG DISTANCE 2, LONG DISTANCE 3) E-MAIL NAME...
Chapter 4 Additional Functions Available Settings 3. DATE TYPE SELECT DD/MM YYYY, YYYY MM/DD, MM/DD/ YYYY(*) 4. AUTO SLEEP TIME ON (3 - 30 (3(*)) MIN. in one-minute increments), OFF 5. AUTO CLEAR TIME ON (1 - 9 (2(*)) MIN. in one-minute increments), OFF 6.
Page 26
Chapter 4 Additional Functions Available Settings 6. CHECKING THE LOG ON, OFF(*) 7. USE DEVICE USB OFF, ON(*) Additional Functions Available Settings 1. SYS. MANAGER INFO SYS. MANAGER ID, SYSTEM PASSWORD, SYSTEM MANAGER 2. DEVICE INFO DEVICE NAME, LOCATION 3. MANAGE DEPT. ID OFF(*), ON;...
Chapter 5 Chapter 5 Service Mode 5.1 Fax System Service Mode 5.1.1 Service Soft Switch Settings (SSSW) 5.1.1.1 Outline 5.1.1.1.1 Bit Switch Composition 0013-1304 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / The items registered and set by each of these switches comprise 8-bit switches.
Chapter 5 Memo: Any of the following error code may be indicated because of an echo at time of reception ##0005, ##0101, ##0106, ##0107, ##0114, ##0200, ##0201, ##0790 5.1.1.4 SSSW-SW04 5.1.1.4.1 List of Functions 0013-1309 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / T-5-3 Function not used...
Chapter 5 T-5-4 Function not used Conversion from mm to inch (text mode) convert do not convert Conversion from mm to inch (text/photo mode) convert do not convert not used not used not used not used not used 5.1.1.5.2 Detailed Discussions of Bit 1 0013-1316 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text mode.
Chapter 5 T-5-9 Function not used not used Convert "inch" into "mm" when transmitting the received convert do not convert image data not used not used not used not used not used 5.1.1.7.2 Detailed Discussions of Bit 2 0013-1320 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / It converts "inch"...
Chapter 5 5.1.1.9.3 Detailed Discussions of Bit 1 0013-1326 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / Select whether to use the V.8 protocol when called. If NO is selected, the V8 protocol is inhibited when called and the V.21 protocol is used. 5.1.1.9.4 Detailed Discussions of Bit 2 0013-1327 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /...
Chapter 5 Function Not used 5.1.1.11.2 Detailed Discussions of Bit 0 0013-7931 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / You can select whether a waste toner full warning is to be displayed. When "1"...
Chapter 5 5.1.2.7 <No.010 Frequency of the pseudo CI signal> 0013-1339 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / You may select a frequency for the pseudo CI signal. Some types of external telephones do not ring when the fax/tel switch-over function is ON. To sound the ring, change the pseudo CI signal. 5.1.3 Numeric Parameter Settings (NUMERIC Param.) 5.1.3.1 Numerical Parameter Composition 0013-1340...
Chapter 5 5.1.3.5 <010: line connection identification length> 0013-1344 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / Use it to set the time for identifying the line connection. Raise this parameter if errors occur frequently at time of communication because of the condition of the line. Memo: Any of the following error codes may be indicated because of the condition of the line ##0005, ##0018...
Page 37
Chapter 5 300s: print 400s: copy + print 500s: scan 700s: received file print 800s: report pint 900s: transmitted scan Guide to the Table - 1:Count sheets of all sizes by one. - 2:Count sheets of the large size by two. - C:full color - Bk:black mono - L:large size (larger than A4/LTR)
Page 38
Chapter 5 Seri Counter type Print system Bk 1-sided L Bk 1-sided S Bk 2-sided L Bk 2-sided S Local Repo Local Repo Local Repo Local Repo copy print print copy print print copy print print copy print print print print print print...
Chapter 5 Seri Counter type Print system Bk 1-sided L Bk 1-sided S Bk 2-sided L Bk 2-sided S Local Repo Local Repo Local Repo Local Repo copy print print copy print print copy print print copy print print print print print print...
Chapter 5 Function Default Setting range Unit 033: Vertical scan magnification correction 0-32 one unit=0.1% 034: Horizontal scan magnification correction 0-32 one unit=0.1% 035: - 036: Reader motor speed adjustment 037: - 040: Not used 041: Vertical scan start position adjustment (scanning 0-70 one unit=0.1mm on ADF)
Chapter 5 0: LEGAL 1: FOOLSCAP 2: M_OFFICIO 3: A_FOOLSCAP 4: FOLIO 5: G_LEGAL 6: A_OFFICIO 7: B_OFFICIO 5.1.4.19 <194: ADF special standard-sized paper: LTR misidentification-ready> 0013-1374 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTR").
Page 43
Chapter 5 T-5-16 Function not used not used not used not used not used not used not used priority on recording in sub scanning direction place do not place Detailed Discussions of Bit 7 0013-1380 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / Use it to enable/disable placement of priority on recording in sub scanning direction.
Chapter 5 Select whether the pre-rotation is to be extended. If white streaks appear in the image in the H/H environment, selecting "Set" extends the pre-rotation by five turns. During the extended period, the charge Vpp is increased to prevent white streaks from occurring. 5.1.5.1.3 SSSW-SW15 List of Function 0013-1387...
Page 45
Chapter 5 5.1.5.2.5 <034: Left-end registration adjustment (manual feed tray)> 0013-1397 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / Adjust the left-end registration margin of paper picked from a manual feed tray. The larger the adjustment value, the wider the left-end margin of the image be- comes.
Page 47
Chapter 5 - Counter clear on parts replacement Press the numeric keypad key 0 after displaying the counter for a part just replaced, and the counter will be cleared individually.
Chapter 5 5.1.8 Report Output (REPORT) 5.1.8.1 Report Output 0013-1411 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / The table below lists the kinds of reports that are supported. Item Explanation SERVICE DATA LIST Service mode service soft switch output (SSSW, MENU, NUMERIC Param., SPECIAL, NCU, SCAN, PRINT, SYSTEM, ROM, start date)
Page 49
Chapter 5 F-5-6 *1: TX, number of total pages transmission. *2: Total number of pages transmitted/received according to original size. *3: RX, number of total pages reception. *4: Total number of pages transmitted and received for each modem speed *5: Total number of pages transmitted/received in connection with different modem speeds (Standard, Fine, Super Fine, Ultra Fine). *6: Total number of pages transmitted and received for each coding method *7: Total number of pages transmitted and received in each mode *8: Total number of pages printed/scanned...
Chapter 5 T-5-22 Indication sample ##280 ##280 ##281 ##282 number of errors number of errors number of errors It provides error information on the 3 most recent communications. 2003 09/02 TUE 12:00 #1 LATEST #000 START TIME 09/02 10:00 OTHER PARTY 12345678 MAKER CODE 10001000...
Chapter 5 Error history description (ERR) Item Explanation Error code Error code (4-digit code; for a definition of the code, see the "Error Code" Chapter.) Detail code Detail code of the error code (4-digit code; for a definition of the code, see the "Error Code" Chapter.) Total counter display 5.1.8.6 Spec List...
Chapter 5 [9] Option ROM availability [10] USB memory availability [11] No. 1/No. 2 paper full sensor sensor availability [12] USB serial number [13] MAC address [14] Backup battery availability [15] Anlog purocessor PCB version 5.1.8.7 Service Label 0013-1417 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / Enter the value given in the service label affixed to the rear cover when it has been replaced with a new one.
Chapter 5 5.1.9 Download (DOWNLOAD) 5.1.9.1 Download 0013-1418 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / The following parts of this unit can be upgraded by executing download mode using the service support tool (SST) (for more information, see the "Upgrading" section): Main unit - Flash ROM (system + boot) mounted on the image processor PCB...
Chapter 5 5.1.13 Test Mode (TEST MODE) 5.1.13.1 D-RAM Test<(1) D-RAM TEST> 0013-1421 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / D-RAM Test((1) D-RAM) Press the numeric keypad key 1 on the test mode menu to select the D-DRAM test. Press numeric keypad keys 1 and 2 during the D-DRAM test to carry out the individual tests described below.
Chapter 5 Use it to make sure that the print Use it to make sure that the print pattern does not have white lines pattern does not have contraction/ or uneven image. elongation of an image or dirt/black line.s F-5-12 5.1.13.4 MODEM Test ((4) MODEM TEST) 0013-1425 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /...
Page 57
Chapter 5 use the keypad. Keypad Frequency 462Hz 1100Hz 1300Hz 1500Hz 1650Hz 1850Hz 2100Hz MEMO: The frequency and the output level of individual frequencies are in keeping with the output level set in service mode. G3 Signal Transmission Test A press on '4' on the keypad from the MODEM test menu selects the G3 signal transmission test. In this test, the following G3 signals from the modem are trans- mitted using the telephone line terminal and the speaker.
Chapter 5 Left/right arrow key Transmission speed 4800bps 7200bps 9600bps < 12000bps 14400bps 16800bps 19200bps 21600bps > 24000bps 26400bps 28800bps 31200bps 33600bps 5.1.13.5 FUNCTION TEST <(6) FUNCTION TEST> 0013-1426 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / Function test ((6) FUNCTION TEST) Press the numeric keypad key 6 on the test mode menu to select the function test.
Page 59
Chapter 5 6-3:SENOR [1] - [8] Press numeric keypad key 1. Press numeric keypad key 0. Press numeric keypad key 0. SENSOR CHECK SENSOR NORMAL CAS 0 REG 0 0:NORMAL 1:LATCH [0] - [2] DEL 0 0 MULTI 0 Select a sensor mode. CAS:Cassette paper sensor (SR9): 0/Document presence, 1/Document absence 0: NORMAL REG:Registration sensor (SR11): 0/Document presence, 1/Document absence...
Page 60
Chapter 5 Press numeric keypad key 4. REF xxx ANT xxx |ANT - LEF| xxx REF: Toner reference voltage (A/D value) ANT: Toner antenna voltage (A/D value) ANT - LEF: Differential voltage (A/D value) Press numeric keypad key 5. BSCT on BDOC[A3 ] BDSS3-0 [of of of of] BSCT: Not used...
Page 61
Chapter 5 - LCD test Start the OPERATION PANEL test by pressing the start key. The LCD test is carried out first, displaying all-H characters. Press the start key once again to produce a total black display. - LED lamp test Press the start key after the LCD test to select the LCD lamp test, turning on all lamps on the operation panel.
Chapter 5 6 - 7 : O P E R A T I O N P A N E L LCD test Press the start key. All-H character display Press the start key. All-black display Press the start key. All-LED illumination LED lamp test Press the start key.
Chapter 7 Chapter 7 System Construction 7.1 Construction 7.1.1 Functional Construction 0013-1074 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF / The machine may be divided into the following 7 functional blocks. Printer communication Fax communication system...
Chapter 7 The image processor comes in different ROM types/sizes and RAM sizes according to models. The firmware stored in the flash ROM may be either SYSTEM or BOOT. Using the service support tool, the following 3 types of firmware may be upgraded: SYSTEM and BOOT stored in the flash ROM and the firmware stored ion PCL ROM.
Chapter 7 Toner Level Detection Mechanism While the machine is in wait state, the toner level detection signal (ADDTNR; based on the comparison of the developing bias output and the antenna output inside the cartridge) occurring when the developing AC bias is detected during normal rotation to monitor the toner level inside the cartridge. 7.1.5 Analog Processor PCB 0013-1078 / / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /...
Page 73
Chapter 7 F-7-4 MPU (IC1) Processes JBIG coding/decoding, controls combinations over lines, and controls SDRAM. PATCH (IC40) controls the various boards (NCU, speaker). SDRAM Controls coding/decoding of image data for transmission/reception, and stores data for the MPU work area and transmission/reception data. MODEM IC (IC1) For transmission, modulates data received from MPU according to ITU-T V.17, V21, V27ter, V29, or V.34;...
Chapter 7 Image margin (trailing edge) 5.0 -/+2.0 mm Image margin (left/right) left: 2.5 -/+2.0 mm right: 0.5mm or more Image mode Yes (text, text/photo, photo) Auto power off Energy save mode yes (manually ON/OFF; auto OFF after specific time, auto ON after fax reception/print data reception) Operating environment 15 to 30 deg C...
Chapter 7 Type Single-sided Two-sided Cassette feed Manual feed Cassette feed Manual feed Envelopes, postcard Monarch 6(4,3,2) COM10 6(4,3,2) ISO-B5 6(4,3,2) ISO-C5 6(4,3,2) 6(4,3,2) Post card 6(4,3,2) Supplement: - (): The speed may change by the state of a fixing unit. - The above copy speed does not change if magnification is changed.
Page 81
Chapter 7 Cassette Manual feed tray Duplex Paper type Plain paper (80 g/m2) Recycled paper Colored paper Heavy paper 1 Heavy paper 2 Heavy paper 3 Bond 3hole punch paper Transparency Labels Envelopes...
Chapter 8 Chapter 8 Upgrading 8.1 Upgrading 8.1.1 Overview of Upgrade 0013-1286 iR1018 This machine and options can be upgraded by downloading system software programs from the personal computer (hereafter called as the PC) in which a service support tool (hereafter called SST) has been loaded. System software programs and upgrade tools are listed in the following table: T-8-1 Type...