hit counter script
Download Print this page
Brother HL-2220 Quick Setup Manual
Brother HL-2220 Quick Setup Manual

Brother HL-2220 Quick Setup Manual

Hide thumbs Also See for HL-2220:

Advertisement

Quick Links

1

Start Here

WARNING indicates a potentially
hazardous situation which, if not avoided,
could result in death or serious injuries.
CAUTION
CAUTION indicates a potentially
hazardous situation which, if not avoided,
may result in minor or moderate injuries.
2
Remove the packing material from the machine
IMPORTANT
DO NOT connect the AC power cord yet.
a.
Remove the packing tape from the outside of the machine and
the silica gel pack from the face-down output tray.
CAUTION
CAUTION
DO NOT eat the Silica Pack. Discard immediately.
b.
Open the front cover.
3
Load paper in the paper tray
a.
Pull the paper tray completely out of the machine.
b.
While pressing the green paper-guide release lever,
slide the paper guides to fit the paper size you are
loading in the tray. Make sure that the guides are
firmly in the slots.
Note
For Legal or Folio size paper, press the release button in the
bottom of the paper tray and then pull out the back of the paper
tray. (Legal or Folio size paper are not available in some regions.)
4
Print a test page
a.
Connect the AC power cord to the machine and then
connect it to an AC power outlet.
Before using this machine for the first time, read this Quick Setup
Guide to setup and install your machine.
To view the Quick Setup Guide in other languages, please visit
http://solutions.brother.com/.
TWN-ENG
Version A
Unpack the machine and check the components
Note
We recommend that you save the original packaging.
The components included in the box may differ depending on your country.
If for any reason you must ship your machine, carefully repack the machine in the original packaging to avoid any damage during transit.
The machine should be adequately insured with the carrier. How to repack the machine, see Packing and shipping the machine in the
User's Guide.
To ensure safe operation the supplied plug must be inserted only into a standard power outlet that is properly grounded through the
standard electrical wiring. Non grounded equipment may cause an electrical shock hazard, and may cause excessive electrical noise
radiation.
USB cable
It is recommended to use a USB 2.0 cable (Type A/B) that is no more than 2 meters (6 feet) long.
c.
Lift the elastic band off the drum.
d.
Pull the paper strip to remove the protective
material as shown in the illustration.
e.
Take out the drum unit and toner cartridge
assembly.
c.
Fan the stack of paper well to avoid paper jams and
misfeeds.
d.
Put paper in the tray and make sure:
The paper is below the maximum paper mark (
Over filling the paper tray will cause paper jams.
The side to be printed on must be face down.
The paper guides touch the sides of the paper so it will
feed properly.
b.
d.
Turn on the machine power switch.
c.
After the machine has finished warming up, the
Ready LED stops blinking and stays green.
CD-ROM (including
Documentation)
AC Power Cord
Drum Unit and Toner Cartridge Assembly
f.
Gently shake it from side to side several times to
distribute the toner evenly inside the assembly.
g.
Put the drum unit and toner cartridge assembly
back in the machine.
h.
Close the front cover of the machine.
e.
Put the paper tray firmly back in the machine. Make
sure that it is completely inserted into the machine.
b b b).
Press
Go. The machine will print a test page. Check that the test
page has printed correctly.
Note
This function will not be available after the first print job you send from
your computer.
Now go to
Turn the sheet over to install the printer driver.
Quick Setup Guide
WARNING
Plastic bags are used in the packaging of your machine. Plastic bags are not toys.
To avoid danger of suffocation, please keep these bags away from babies and
Quick Setup Guide
Safety and Legal
children and dispose of them properly.
Booklet
Note
Keep a minimum gap around the machine as shown in the illustration.
100mm
(4 in.)
USB Interface Cable
(pre-installed)
Printer LED Indications
Blinking:
or
or
Printer LED
OFF
SLEEP
DEEP SLEEP
Toner
Drum
Error
Ready
Dimmed
Printer LED
TONER LOW
REPLACE
3
TONER
Toner
Drum
Error
Ready
Chapter 4
Chapter 4
User's Guide
Printer LED
COVER OPEN
NO PAPER
PAPER JAM
2
Toner
Drum
Error
Ready
Chapter 5
Chapter 5
User's Guide
The LED will blink ON and OFF at 1 second intervals.
1
2
The LED will blink ON and OFF at 0.5 second intervals.
The yellow LED will blink in a pattern of ON for 2 seconds and then OFF for 3 seconds.
3
You can change the toner setting to the continue mode. Press Go seven times (all the LED flashes
4
twice, and then the Ready LED is on).
The machine continues printing until the LED indicates the toner ended message.
HL-2220
HL-2240D
100mm(20.1 in.)
100mm
(4 in.)
120mm
(4.72 in.)
ON:
or
or
OFF:
WARMING UP
READY
RECEIVING DATA
COOLING DOWN
1
DATA REMAINING
2
TONER
DRUM END
REPLACE
4
ENDED
SOON
3
DRUM
Chapter 4
Chapter 4
Chapter 4
DRUM
DRUM STOP
Service call
ERROR
error
2
2
Chapter 4
Chapter 4
Chapter 3

Advertisement

loading

Summary of Contents for Brother HL-2220

  • Page 1: Start Here

    Before using this machine for the first time, read this Quick Setup Guide to setup and install your machine. To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/. HL-2220 TWN-ENG Version A HL-2240D Unpack the machine and check the components...
  • Page 2: Mac Os X

    • If there are any programs running, close them. If the Brother screen does not appear automatically, go to My • The screens may differ depending on your operating system. Computer (Computer), double-click the CD-ROM icon, and then double-click start.exe.

This manual is also suitable for:

Hl2240d