Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Wear eye
refer to
Protection
instruction
manual
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the sharpener is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable
Appliance test) tested.
1.1.1.
electrical safety information, it is important that the following information is read and understood. ensure that the insulation on all
cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
1.1.3.
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 5 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
B) Connect the BROWN live wire to the live terminal 'L'.
C) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician
GENERAL SAFETY
1.2.
disconnect the sharpener from the mains power before changing accessories, servicing or performing any maintenance.
1.2.1.
maintain aluminium oxide wet stone and cow hide honing wheel in good condition. check moving parts and alignment. if necessary use
an authorised service agent.
1.2.2.
replace or repair damaged parts. Use genuine parts only. Unapproved parts may be dangerous and will invalidate the warranty.
1.2.3.
the sharpening wheel must only be changed by persons holding an appropriate grinding wheel certificate.
1.2.4.
Wear approved safety goggles.
1.2.5.
remove ill fitting clothing. remove ties, watches, rings, and other loose jewellery, and contain long hair.
1.2.6.
use sharpener in a suitable work area, keep area clean, tidy and free from unrelated materials, and ensure adequate lighting.
1.2.7.
maintain correct balance and footing. DO NOT over-reach and ensure the floor is not slippery. Wear non slip shoes.
1.2.8.
use only approved stone, never use the side of the stone.
1.2.9.
Check sharpening stone/honing wheel to ensure they are not split, cracked or damaged in anyway, if in doubt DO NOT use.
1.2.10.
sharpening stone/ honing wheel must be securely attached before use, but not over tightened.
1.2.11.
Keep non essential persons away from the working area.
DO NOT operate the sharpener if any parts are missing or the sharpener is damaged.
8
DO NOT use the sharpener for a task it was not designed to perform.
8
DO NOT operate sharpener where there are flammable liquids or gasses.
8
WARNING! DO NOT sharpen any materials containing asbestos.
‰
© Jack sealey limited
instructions for
SHARPENER Ø200mm with HONING WHEEL.
model no:
ELECTRICAL SAFETY
AL
Original Language Version
SMS2101
recommended fuse rating
5 Amp
sMS2101 | Issue 1
10/03/16
Advertisement
Related Manuals for Sealey SMS2101
Summary of Contents for Sealey SMS2101
- Page 1 SMS2101 model no: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Model No: ........SMS2101...
- Page 3 Fig.2 Fig.4 Fig.3 Fig.5 Fig.6 Original Language Version sMS2101 | Issue 1 10/03/16 © Jack sealey limited...
- Page 4 Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500. Environmental Protection recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.