Related Manuals for AEG 88101
Summary of Contents for AEG 88101
- Page 1 SERVICE MANUAL HOBS Repair-Instruction Publ.-Nr. for induction hobs 599 519 523 DGS-TDS-N Ausgabe: 04.08 DGS-TDS-N 21.04.08...
-
Page 2: General Information
599 519 523 EN 1 General Information These instructions serve the repairing of autarkic cooking hobs and cooking hobs in combination with an oven with 3 or 4 inductions cooking zones respectively of the type E.G.O.. Also includes hobs with 2 induction zones (Domino, Mixed, Mixed gas) and the Frontline appliance series. - Page 3 599 519 523 EN 1.3 Block Diagram/Hob elements Coils incl. Temperature sensors. Touch control w. carrier Cover plate Coil carrier Cooling fan Induction module w. plastic housing incl. mains terminal Filter pcb Power mod. Left PowerMod. Right DGS-TDS 21.04.08...
- Page 4 599 519 523 EN 2 Alarm Symptoms 2.1 Appliance not functioning at all, cannot be switched on References e.g. (1) refer to the illustrations in Chapter 2.8 Alarm Symptom Cooking Possible Alarm Alarm Remedying Cause Display House fuse triggered None Incorrect connection at (1) Test the pin assignment and the power connection...
- Page 5 599 519 523 EN 2.2 Individual cooking zones do not work (partially) or work incorrectly or cannot be used Alarm Symptom Cooking Possible Alarm Alarm Remedying Cause Display Pan does not heat Normal Pan in the border Use different pot or this pot on a smaller cooking area of the pan hob.
- Page 6 599 519 523 EN 2.3 Alarm message "E“ When the appliance is switched on, "E“ / „xx“ Alarm Number is displayed in the timer display. With Frontline the display of the front zone indicates the error number when switching on. The affected zones are subsequently displayed with an "E"...
- Page 7 599 519 523 EN Alarm Display Possible Alarm Alarm Remedying in the Symptom Causes Cooking Field Timer Alarm display in the "E5“ 1 phase missing 1) Check the house fuse. Touch Control 2) Check the pin assignment, (1) test L1 against N (4), test L2 against N (5) 3) If ok, see Chapter 3.
- Page 8 599 519 523 EN 2.4 Other alarm symptoms Alarm Display Possible Alarm Alarm Remedying symptoms Cause Buzzer defect Touch control Replace Touch Control. defect. Individual display Defective display Replace Touch Control. elements do not elements illuminate or do not do so continuously. Penetrating aromas Coils subjected to a The aroma is non-toxic.
- Page 9 599 519 523 EN 2.5.1 Electric heating element relay instructions • Refer to the wiring diagram xxx. The electric heating element is pulsed on relay board HOC2000 in the cooker. • Phase commutation with the cooker/hob combination, refer to Chapter 2.6, special error images for the cooker/hob combination.
- Page 10 599 519 523 EN 2.6.1 No display or error display on the cooking zone display on the cooker Alarm symptoms Display Possible Alarm Cause Alarm Remedying Error display "E". "E" if the Errors in the cooking zone display in the cooker concern the hob. I.e. the display same error number is displayed as in exists.
- Page 11 599 519 523 EN 2.6.2 Cooking zone at the cooker okay, no display at the hob or no output. Alarm symptoms Display Possible Alarm Cause Alarm Remedying The diplay in the hob does None. Output connector not Check the connector (10) and not illuminate when voltage is inserted..
- Page 12 599 519 523 EN (10) (11) (13) (12) (14) Display in the hob 4 hobs dep. In comb. With cooker (14) external user Interface 2.7 Unknown display For details, refer to the cooking field instruction manual Symbol Comment Intermediate cooking levels („4.“) „...
- Page 13 599 519 523 EN 2.8 Control Point Illustrations Terminal Pin 1, 3 Air - Min. 5 mm inlet Min. 20mm Oven Remark: if there is no ventilation gap in the front it’s still possible to operate the hob. Only with longer useage ( >15 min. ) the performance will drop.
- Page 14 599 519 523 EN 2.9 Images control point for 2 zones / Mixed Induction Attention: mains connection for Domino is directly on filter pcb. (1) Domino DGS-TDS 21.04.08...
- Page 15 599 519 523 EN 3 Testing Power Component 1. When alarm messages and disabled zones exist ("E“ in cooking phase display), please make a note of the power component which is affected. 2. (7) Check whether the lead from the filter board is connected, also check the bus lines (6) µprocessors filter to power component.
- Page 16 599 519 523 EN 4 Pot Detection Information Suitable pot materials: • Steel enamel • Stainless steel (with magnet. bottom) • Aluminium (with magnet. bottom) • Cast iron Unsuitable materials: • Aluminium ( too much power) • Copper • Stainless steel (not magnetic) •...
- Page 17 599 519 523 EN 5 Touch Control Autarkic Cooking Hobs Information • The Touch Control works on the basis of the infrared principle, i.e. a signal is transmitted with a transmitter which is then reflected by the finger and received once more. 5.1 Instructions on the operation / possible operation errors if the buttons do not function: •...
- Page 18 599 519 523 EN 5.2 Demo mode / Self test (Service mode) / Alarm Menu To enter the self-test/Demo mode, the following sequence of buttons must be pressed: 1. Hob is off. Press main switch continuously until display is going off (without beep). 2.
- Page 19 599 519 523 EN 5.3.2 Error appliance can not be operated, display indicates "0" This error has been disappeared after a reset. For that there were 2 fault reasons in the hardware and software, this was removed by SW Vers. 4.2 from Dec.
- Page 20 599 519 523 EN Assembly of band cable (30) (31) Open locking (black bar) Put band cable (silver contacts visible) Close locking in arrow direction (32) Turn down the electronic with displays onto the glass side, press the carrier flatly to the glass lower side and let it lock in.
- Page 21 599 519 523 EN 3. Then automatically the software version of the user interface is displayed, for example „2“ „8“ = version 28 and all LEDs / Displays are ON for 10 Sec. There is no alarm history mode available. 4.