ICD-ST25 TABLE OF CONTENTS 1. GENERAL Notes on chip component replacement ·········································································· 3 • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be dam- 2. DISASSEMBLY aged by heat. 2-1. Case Block Assy ··························································· 4 2-2.
ICD-ST25 SECTION 1 GENERAL This section is extracted from instruction manual. Index to Parts and Controls Refer to the pages indicated in parentheses for details. Rear Front 1 Built-in microphone (12, 14) 0 Speaker K zREC (record) /REC 2 Built-in microphone (12, 14)
ICD-ST25 SECTION 2 DISASSEMBLY Note : Disassemble the unit in the order as shown below. 2-1. CASE BLOCK ASSY (Page 4) 2-3. 2-2. MAIN BOARD F-SW BOARD (Page 5) (Page 5) 2-4. S-SW BOARD, MICROPHONE BLOCK ASSY (Page 6) 2-5.
ICD-ST25 2-5. MICROPHONE UNIT 7 microphone cover 8 microphone cushion Microphone part is turned in the direction of arrow and it removes in the direction of arrow 9 microphone unit 0 microphone case screw hole part 6 pan tapping screw 2 click plate (M1.4 ×...
ICD-ST25 2-6. THE CAUTIONS AT THE TIME OF A MICROPHONE BLOCK ASSY microphone unit microphone cover flexible board It inserts in a microphone base. screw hole part microphone cushion microphone unit microphone case microphone base It turns in the direction of an arrow.
ICD-ST25 SECTION 3 TEST MODE [Setting Method of the Test Mode] [Operation in the Test Mode] To enter the test mode, turn on the HOLD . switch while pressing After entering the test mode, you can move within the test menu by the x key and VOL+ key at the same time with the power on.
Page 10
ICD-ST25 3. Sleep test 7. Battery remaining power and DC IN test • Pressing the x•B key causes the set to enter the sleep state. • The detected A/D value (hexadecimal) of the battery remaining • When the HOLD . switch is ON, the LCD is turned off.
Page 11
ICD-ST25 11. Key durable test • Pressing the x•B key makes the count to "------" and sets test standby status. Once more pressing the x•B key makes the count to "000000" and sets the key durable test. In this mode any key input and slide switch operation are counted and the number is displayed.
ICD-ST25 SECTION 4 DIAGRAMS Note on Schematic Diagrams: Note on Printed Wiring Boards: • Y : parts extracted from the conductor side. • All capacitors are in µF unless otherwise noted. pF: µµF • b : Pattern from the side which enables seeing.
ICD-ST25 4-2. PRINTED WIRING BOARD – MAIN BOARD (SIDE A) – • : Uses unleaded solder. (SIDE A) MAIN BOARD J5001 C5012 R5012 J3002 C1008 CSP(Chip Size Package) C6002 C2009 J3001 m P L U G I N P O W E R...
ICD-ST25 4-4. PRINTED WIRING BOARD – F-SW BOARD – • : Uses unleaded solder. (SIDE A) (SIDE B) F-SW BOARD F-SW BOARD O P R E R A S E V O I C E U P D P C O N / O F F...
ICD-ST25 4-10. SCHEMATIC DIAGRAM – MAIN BOARD (5/5) – • See page 32 for IC Pin Function Description. (Page 21) (Page 20) Q7004 UN9214J-(K8).SO R7027 100k R7028 D7004 1SS352 R7030 Q7005 UN9214J-(K8).SO (Page 20) C7017 X7001 4.096MHz R7041 S7001 HOLD...
Page 25
ICD-ST25 • IC BLOCK DIAGRAMS IC3001 LA7473V-TLM-E (MAIN BOARD) INT MIC OUTPUT AMP R AMP R AMP R EXT MIC AMP R EXT MIC BIAS EXT MIC AMP L OUTPUT RIPPLE INT MIC AMP L AMP L FILTER AMP L...
ICD-ST25 4-11. IC PIN FUNCTION DESCRIPTIONS • IC6001 uPD77213F1-101-DA2 (DSP) (MAIN BOARD) Pin No. Pin Name Description 1 to 3 — Not used EVDD — I/O power supply (3.1V) XADACS AD/DA chip select (Not used) (fixed at “L”) ADACCLK AD/DA clock (Not used) (fixed at “L”) ADACDTI AD/DA data input (Not used) (fixed at “L”)
Page 30
ICD-ST25 Pin No. Pin Name Description Memory address bus 0 (Not used) — Ground terminal IVDD — Core power supply (1.6 V) Memory address bus 2 (Not used) Memory address bus 4 (Not used) — Ground terminal Memory address bus 3 (Not used)
ICD-ST25 Pin No. Pin Name Description Memory data bus (Not used) MD14 Memory data bus (Not used) — Ground terminal MD15 Memory data bus (Not used) MD12 Memory data bus (Not used) TICE Test ICE Test mode selection EVDD —...
Page 32
ICD-ST25 • IC7003 MB91F233 (CPU) (MAIN BOARD) Pin No. Pin Name Description DSPSCK Serial clock output for DSP FLMCLE Command latch enable signal output for FLASH 3 to 10 DATA0 to 7 Data input/output to FLASH and USB XFLMCS0 Chip enable signal output for FLASH...
ICD-ST25 SECTION 5 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number have some differences from the original one. in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service.
ICD-ST25 SECTION 6 ELECTRICAL PARTS LIST F-SW MAIN NOTE: • Due to standardization, replacements in the • CAPACITORS: • SEMICONDUCTORS parts list may be different from the parts uF: µF In each case, u: µ, for example: specified in the diagrams or the components •...
Page 42
ICD-ST25 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2004.03...